Cisco Wireless

Hi, I would like to know if it is possible to make comments of web authentication to the single autonomous access point? I've done web authentication for comments on the WLC with lwapp AP successfully. Please notify Sent by Cisco Support technique iP

All, I have a 881W integrated services router that has a built-in 801 access point.  I want to upgrade the software on the 801AP for a newer version.  Here's what it is running: -------------------- PC - PA #sh wormSoftware Cisco IOS, AP801 Software

Hey everybody, I hope someone can help with a few questions.  First of all, I had a customer ask if there's sort of a device, for example an IPad or smartphone, fingerprints and automatically reduce bandwidth bandwidth, similar to a role or a QoS pro

We deploy more devices Apple to serve hand records/check points that connect to the LAN via the wireless. So far, we discovered that the same ssid running on 2.4 & 5 ghz makes very unfortunate Apple. Would like to know if anyone has the "best practic

Hello I plugged WLC on the main switch on concert 5/5, Mac address table is lower to -. kernel #sh mac-address-table Unicast entriesport of protocols VLAN mac address type 4001 8843.e131.1983 dynamic ip GigabitEthernet5/54001 8843.e131.198b dynamic i

I have a 1242 that has been configured for LWAPP and reset to the factory settings. I'm curious to know if returned in standalone mode? Thanks in advance

Hello I don't see the rcb of the order part.  Other thoughts? Thank you Tim 1140 #debug lwapp customer? debugs CC Call Control associated with LWAPP Client Config Messages config Customer LWAPP Error Messages error event Client LWAPP debug event LWAP

Hello you want to know AP1230s how much I needed to take charge 150 customers in a large conference room.  Until someone started on me, these are the only available APs.    Customers will be a mix of the laptops using a variety of different adapters.

Hello world I have a couple of these nine APs but apparently through the CLI (serial connection) I can not put the command "configure." I access mode privilege with the password, but after that I can't do anything. Most I've seen on the cisco site th

Hello I have cisco AP 1242 AG with 2.4 ghz and 5 GHz in frequency. Can someone tell me what the difference is and also let me know if we can use the 5 GHz frequency according to Indian regulations of RF.

Hello We install many AP on my desk. I have to write a rules that establish the minimum required signal before installing a second access point or a Repeater at the same place.  Can someone tell me what is the minimum signal strength is acceptable be

Just out of the box. Set the IP address, security and turned on the radio. When I checked the gigabit interface, it indicates: Software status - enabled State of the material - down Is this an indication that the AP has a hardware problem and I can s

We have a Cisco 4402-25 running the 7.0.98 software version and we are interested in getting a new controller of 5508.  My question is can I load balance between these two or an act as a master and the other a slave?  Thank you

Is the new 5500 WLC supported several Web Auth login pages? I want to consolidate my WLCs in a central place and maybe just a controller. I have several different comments for different departments wireless networks, and each has a custom login Auth

Hello I have two 1300 an AP configured as one other bridge as a bridge mode no root. Right now I have it set to a subnet and it works. Now, I have to add a subnet more in my network, for that I need to configure the SSID? My topology is sort of this

Hi all The AIR-LAP1142N-E-K is completely compatible with AIR-WLC2106-K9?

Hello. Can someone point me to a reference guide for the meanings and reasons for the LEDs on a lightweight access point 1242 please.  I'm sure that this information was available, but I am unable to find it. Thanks in advance. Robin

Hi all appreciate your support for a problem I started to deal with today. I have a Cisco WLC 4402 running the 7.0.116.0 version and it's great to work with 25 Cisco 1252 access points. We received a new 20 Cisco 1041N APs today and I installed one i

I have configured our Ap 1141 with two ssid. One is the ssid of comments and the other is marked for advertising in the SSIDl IE.  I see that the guest in the broadcast mode ssid.  I can connect at once if I manually configure the client to connect t

Hello can you recommend a good place to train you wireless at the coast is (New York/New Jersey area) Thank you Tony