Dell Switches

Have this question about 2748 mode managed connection, I just bought. 2008-05-19 After the initial 'admin' connection unit by default, the page of ' restore saved Configuration.  I can't go past this page to enter my network settings. Only the button

So, I probably just forgot somewhere, but now that I've spent some time looking and did not find, I thought that I would just ask. We are planning to use a 6224 as a border router in an OSPF environment heavy (~ ~ thousand prefixes).  This seems like

Nice day I bought two layer 3 PC 6248 switches. When I try to assign an IP address by default VLAN 1, it displays an error 'failed to remove management VLAN - ID ".  These predisposees are already preconfigured with the IP address 192.168.0.1 for VLA

I have a stack of 4 PC 3448 of the switch with 20 3424 switch is related to them. I was thinking of setting up some for the redundancy of the LAG / speed for all 3424 switches. 8 GAL with 8 ports per LAG limitation applies to each switch or the batte

OK, here is what I am wanting to try: PC6248 > Cisco 2800 router Cisco 2800 router > PC6224 I have 4 VLANS which would go through this link: 8 100 102 and 103. And that's how I think I will need to configure the VLAN: 6248: switchport mode trunk swit

One 2724 PowerConnect -Managed -IP: 192.168.10.42 -No LAG -No VLAN From a computer, I can another computer and receive the following: everything is fast. Reply from 192.168.10.105: bytes = 32 time Reply from 192.168.10.105: bytes = 32 time Reply from

Hello, all. I have a LAG of 4-way connecting two 5448 switches I attempt to isolate the VLAN 1000.  Here's my config, which currently does not seem to work: on switch A database of VLAN VLAN 1000 output int range eth g(1-4) switchport access vlan 100

I just bought a Dell powerconnect 3024 on ebay that apparently has been decommissioned corporate. Based on the serial number, warranty or service with Dell expired? Or the seller or the company, that he came remembers the password so the only alterna

Hi all. Just got a switch configuration quad for our infrastructure EqualLogic SAN using PowerConnect 5448 s.  One thing I never did before her configuration of aggregation of links. If I wanted to set up an aggregate of 4-port connection between two

2 questions about the PowerConnect 6024- 1-how to start the Setup Wizard once the switch has been set up?  I tried to remove the startup-config and reload but that does not seem to start the installation wizard. 2 - the main reason I ask question 1 i

Hello world I hope someone can help me with that. I have a pc 6248 as the core of our network and 4 pc 3448 than edge. I installed a 5 (printers) vlan with the subnet 172.10.10.0 24 on all switches 172.10.10.10 - pc 6248 172.10.10.12 - switch 1 (pc 3

We run on optical fiber with Embarq on their ethernet point to point service. On the 6224 I MTU normally the default value of 1518, Embarq sets the MTU in their Cisco 3400 to 1546. When they do, we have major problems with traffic, not to complete an

Hello. I need for firmware (and boot code) updated over 40 switches PowerConnect (mainly 5324). What is the best practice on that? I tried to download and install Dell OpenManage Network Manager, but it seems like an application of 'disorder' for som

I just upgraded PC6248 pile of 1.0.0.27 at 2.0.0.12 update went well, without any problems. Stack consists of two 6248 switches. There is only one problem (but big enough), I can't save my configuration: --- pc6248 #copy running-config startup-config

Hi, I have now successfully configured my PowerConnect 6224, host and road between the 4 VLANS, I have access to the internet and can ping I have, is all great work. The next thing on my list is to set up my router L2 netgear to work with the port ba

I got successfully my inter vlan routing and DHCP work. I also had access to the Internet since the 192.168.2.0 subnet. My router is a netgear FVS124 IP 192.168.2.201, this router is connected to port 1/g24. When I try to connect to the internet, or

I'm trying to upgrade a PowerConnect 5324 sw 1.0.0.47(boot ver 1.0.0.21) to sw rev 2.0.0.40(boot ver 1.0.0.2) rev. I have download the new code to the switch and boot images has changed. After booting on the new firmware image, I see the message "Arc

Hello I just the 6248. VLAN 1: 10.0.1.1/24 VLAN 300: 10.254.0.1/24 Gateway: 10.254.0.10 //residing on VLAN 300 I can ping to the gateway of the VLAN 1, I can ping hosts on VLAN 1 from VLAN 300, but I can't access internet from VLAN 1.  VLAN 300 has n

I have a 6224 with some VLANs set up. I have addresses assigned to most of VLANs (i.e. "configuration, interfaces, vlan 20, ip 192.168.20.254 address '). I can't seem to find a way to have the switch shows that vlan interfaces have this ip assigned,

I really need your help on a 2724 switch. My new job, there is an existing PowerConnect 2724 and he is currently in managed Mode 2 VLANS. I have Do not have the IP settings or passwords. I put my settings TCPIP 192.168.2.2 and my MASK of 255.255.255.