Dell Switches
PowerConnect 6224 VLAN Routing, unable to connect out of VLAN but able to connect by entering.
To set up a new VIRTUAL local network to separate the common workstation network and obtain new DHCP scope, I had a few questions and found advice in the post of http://en.community.dell.com/support-forums/network-switches/f/866/t/19370806.aspx?PageI
Not able to go online, all at once via powerconnect L3 switch
Hello We have dell sonic firewall and then switch 6248P, all of sudden, we can't go online, however we can always connect to our site-to-site VPN When we plugged directly after the firewall, can go online, but via the switch. Please suggest. Thanks i
6224 does not get to the internet on vlan-111
Unable to get to the internet, ran tracert, and when it does respond it shows 192.168.98.254 as next hop. not good. On switch port 8 is vlan-1 management port 192.168.2.0/24 on switch port 5 is vlan-111 end-users 192.168.111.0/24 on switch port 21 is
Definition of VLAN ACL blocks all traffic inside of the vlan
Hello I test a 7024 PowerConnect switch, do some VLAN and want to test the traffic between 2 PC connection to the vlan by default. So I put a PC on Port 1 and the other on Port 2. I am applying only a permit ICMP any any rule on this vlan. This impli
Force10 MXL - stack or do not stack
Hi guys,. If the availability is the most important thing, trunk or battery MXL rocking? I like simplified management, ability to balance the load on several links but I am concerned about uptime during the upgrade firmware (5-10 minutes?) and the po
Port mirroring for the uplink of 10 GB of PowerConnect 6224
I need to take a copy of the traffic over a 10G fiber link. The amount of traffic on this link is less than 1 Gbps. I am considering using the mirror port on a PowerConnect 6224 for this function. However, I don't know if port mirroring also works on
5324 disable vlan 1
Hello I would like to disable the vlan 1. I read in the manual of the cli on command vlan by default disable. But in my 5324 is not so option. I've updated to the new firmware, but still do not have this command. This device recognizes this command?
For a client WIFI VLAN access control list
I am getting my 70 VLAN (GUESTWIFI) access only to the Internet and to deny access to the local network. I set up the ACL below but I can't road on through my firewall (it has 2 interfaces, 1 is a subinterface) Can someone tell what I am doing wrong
Disable the tree cover on 2724?
We are a Cisco shop but we commonly use 2724 switches when we need a low-cost switch GB pre-installed. This is useful when you have a large group of servers on the same VLAN. We disable BPDU guard on the port of Cisco, since there are very few chance
Buffer size of package on PowerConnect 6224
Unfortunately I have been unable to find data about the size of packet buffer size for the switch. Someone has this secret knowledge? :-)Thanks in advance.
installation confusion 6224
I'm trying to configure a 6224. I have reset to factory settings so much times again now and I am very frustrated. This is my first time up to a layer 3 switch setting. My config running can be started on easy enough if someone could possibly help
6248P TROLLING MAX FRAME SIZE Question
Just curious, if there is no performance gain by increasing the size of the frame of the ports in a GAP between two switches (both are 6248P)? If Yes, what size would be best?
Help design 6224 Vlan stack config
Hi all I'm looking for help for what I feel should be a simple configuration. I have 2 6224 switches in what will be a stacked config. I need to put in place the following VLANs VLAN Database 5,6,7,8,9,90,100-254 VLAN 6,7,8,9 should be isolated from
PowerConnect 8132 routed Port
Good morning/afternoon everyone, I come from a world of Cisco, but we decided to buy Dell PowerConnect 8132 because they were cheaper. In Cisco, I can easily make a port on the router, for example: interface GigabitEthernet0/2 no switchport ip addres
GraphingTX/RX on Vlan can connect 5424
Hello We recently started using Observium as a networkgraphing and he uses SNMP to retrieve transferdata for physical ports, but it fails for VLANs, it is even possible in the firmware to do? The data for large physical ports work and I just want to
PowerConnect 2824: Can't access web management using VLAN TAG 1?
Let's say I have port 20, which is a member with LABEL of VLAN 1, 10 and 20. If I try to access web management to help interface VLAN 1 TAG, it is not accessible. However, if I remove the tag VLAN (and the default PVID value of 1), then it works fin
STD + Cisco 8024f
Hello I am trying to install SwA (cisco WS-C3560G-24PS) SWB (cisco WS-C3560G-24PS) CFC (8024f) SWD (8042f) I stacked CFC & swd (such as CFCS). My links are so SWC 1/0/1 & 1/0/2 stacked related swc2/0/1 & 2/0/2. These are my stackable ports! SwA gi0/1
Problem with the Dell powerconnect 5424
Hi all!! I got 2 switch dell powerconnect 5424. I set them up with an IP and everything goes well (for now). But when I connect a switch on the network I have this message: 1 January 2000 00:01:07 % STP-W-PORTSTATUS: g21: STP Forwarding State1 Januar
Install the new switch
I am replacing an old switch with a 5424, which is, "to connect to a console running terminal emulation software" it... can someone help me get started here, I have no idea what the quick start guide tells me to do... Thank you...
3024 can connect and new servers
We bought a Powerconnect 3024 switch, years before I started and we are again moving servers with a new internal IP address range. Will I need to configure the Powerconnect switch to the new range as well, or will it continue to work.