Dell Switches

Hello is - anyone idea, if possible to use frames only for ports specific it s? After enable JumboFrames, it will create a problem of common computers network traffic? I intended to create a VIRTUAL LAN to connect to the storage and r.620 (under XenS

I switched 10gig Dell Powerconnect 8024F. "One of them is to have events NOTICE in the newspapers:" DHCPCLIEN Unable to acquire an IP address on intIfNum - 274; DHCP server has failed. " It is infinitely loop on each of them.

Hi Im new switches Dell but, so far, Ive been going good and syntax very familiar I used of. I have a question where I have multiple VLANs and I try to create an Ip address for the interface VLAN 1 but he won't come. My other interfaces vlan come but

Hello I recently put one of our old clusters online it's a server poweredge 1855. I work at 5 knots, and there a PowerConnect 5316 M switch on the back. 5316M has only 1 cable connecting the switch to uplink. Each blade has 2 NIC one of them is a NIC

Hello We are seeing packet loss on our voice network which causes the phone sometimes sounds without interruption.  This could be the result of oversized packets (more details below).  On a separate note, if I transfer images using Windows Deployment

Hello Just a question.  A Dell Powerconnect 5448 switch will act as a home if its interfaces are configured with 1 interface connection to a primary switch that has the interface is 'access to the interface mode' by default with a vlan?  It will work

I currently Powerconnect 6248 and 6224 switches via my network.  On a floor 48 port switch is full and I need to add another, my thought is to add an another 6248 and stack them, but told me that I should get the 5548 and use sfp + 10 gig connection

Hi support them Is it possible to access the use of memory and processing power charge connect 6224 via SNMP? If possible, should the mib I use? Thanks in advance Rogerio

Hello When I check the temperature of the PowerConnect 8132F I can see the PHY and MAC temperatures. What do these? Thanks for any response. Kind regards Martins

I have several switches Dell powerconnect 3548 and 5548 deployed on my network to install multi that I'm managing their individual DNS names.  now, I've added a voip phone system that works on my network, but to a range of ip addresses completely dif

Hello. We have a strange problem. Because we are not networking gurus, we use the web interface of the switches to manage them (instead of using the CLI). The problem is that when connect us to the web interface of WS2012, the browser (IE) freezes. W

Hi guys,.im a Sysadmin Linux\VMware that starts with networking, sorry for my stupid question newbie and thanks for the support. It's my scenario: 2 X PowerConnect 5448 2 X PowerEdge 2950 3 X PowerEdge 1950 1 X PowerVault MD3220i VLAN: VLAN 1 Product

Hello everybody, I got a Dell PowerConnect 5324 switch and I try to manage it. I connect it to a computer with a null modem cable and I run PuTTY 0.62. I set options to : Connection: serial Speed: 9600 Data bits: 8 Stop bits: 1 Parity: None Flow cont

Hello! I use 'Authentication Port' on my PowerConnect 2848 switch, the RADIUS server is Windows Server 2008 R2. Workstations authenticated correctly and everything works well. For my devices VoIP which does not support the RADIUS, I would add the MAC

I'm pretty green when I just went and routing configurations please bear with me.  I'm available what I want to achieve and what I could do until now (although it may be completely wrong). I have an office where we run low on IP addresses for our loc

Hello I inherited two switches 6248P outgoing Manager (I arrived after his departure) and would like to know if the switch can add a port for a 10GBASE-SR fiber connection.  One of the switches is in place and in the course of execution attached to a

Hi all I need to extend the desktop LAN by connecting a battery of CISCO 3750 existing a new pile of DELL 6248. I intend to use the fiber/combo harbour in DELL 6248 to connect to the CISCO uplink port. I want to use DELL port 48 but I saw there was 1

In the user Web interface for my stack of switches 5548p, if I go into the settings of local network VIRTUAL port, click on edit, select a port and change the mode of access on the trunk port, the changes are saved, but then the button apply disappea

I read the Protocol VRRP implementation documents, and it seems pretty simple. The question I have is this: The switch updates the configuration of the backup/slave switch automatically when changes register to the startup-config? I basically just wa

I noticed, under system, advanced settings, General settings, there is an entry of stackable port with the ability to select the copper Ports or fiber. 35xx switches can now use fiber for stacking ports? Someone at - it tested?