Dell Switches

I am very new to these switches. Just bought a pair of 8132 PowerConnect switches to 5.1.0.1 Firmware, and I'm trying to disable some ports on them through the web INTERFACE. There is a parameter called "Admin status", which I can put on Disable, but

Hello! I have question about the Ports protected on Dell Powerconnect 6248. What I want to achieve - two devices, one connected to the port39 and the other at 40 cannot talk to each other. I assumed that this can be done forwards with function "prote

Guys, No idea why the tftp operation will only copy the 3.3.5.5 firmware to one of the two 6248 s in the stack? Thank you TVB

Hi, we have a stack of 2 x 7048 s who are (is?) configured as a default gateway for a number of VLAN from some Dell blade chassis. I won't go into too much detail because it's more of a conceptual thing I need to know 8 x VLANS, which are all x.x.x.2

Hello. I have a Dell Powerconnect 6248. This used to be a secondary switch in a stacked configuration (total of 2 switches). However, the captain then descended down we unplugged and it became the master of the battery. It is always configured in a c

Hi people, First of all, I am 100% new to the Dell model of switching. Secondly, I have only with this company a month and have been putting out fires more than any individual in that my age should have! My last 3 alarm fire, it's that I'm VERY diffe

We have two blade m1000e, each with 2 switches m8024-k chassis.  We use this document (see link below) to connect to four cisco 5 k http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20065722/download.aspx We chose to use the scenario 3 (p

Back again with a new question... I recently inherited our network in a small college private boarding school preparation.  The network has been set up by an outside company, several years before my arrival.  There is little documentation (as I know)

I have create a pile between two switches Dell PowerConnect 8164.But I want to know if I could change the time it takes for converges converges moment between them, I want to say... I have remove all the stacking cables (so no connection between no s

I need to connect two powerconnect M6220 to LAN infrastructure existing. The switch of two are configured in the stack. Which is the best way to uplink the new switch to the other two powerconnect 5548. The old switch are not stacked and bound togeth

HIII am setting up a test lab to the office and found 2 switches PowerConnect (a 3524 & a 3548)I know he can do stack by ports G3/G4, but I can't make it work... hope someone can enlighten me. ~ Here is what I have tried/fact:Connect the right port 3

Hey guys,. I have a basic > intermediate understanding of networking. I recently loaded the research in what seems at first sight be an STP issue on our corporate network. Without going into too much detail, I think I found the cause of the problem.

Hello first of all, I hope that a good place to ask question re Force10 devices - if not please forgive & point me to the right place I have following two stacked devices: Type of system: S50NReference Dell Force10 operating system Version: 1.0Refere

Hello!I want to copy running config/start switch 8164 to the TFTP server config. On the desktop, I use Cisco TFTP's that works very well for the copy of the files beetwen cisco devices. but I don't know what good command of switches dell.It is said t

Hello I need to split my 5224 into 2 VLANS. I created a second VLAN (222) and configure the ports for it (11-16) However, I can not then remove these ports in vlan 1. The web interface won't let me mark it as white They must be completely separated f

Dear friends, I have 2 switches powerconnect 6224 interconnected using optical fiber and XFP ports on the rear panel of the switch. There is no configuration of the battery between them. The distance between the two switches is 500 metres and they bo

Hello I just upgraded a PowerConnect 6248 3.3.5.5 at 3.3.7.2 switch and took the panic over the serial console stack trace. I've now returned to the 3.3.5.5 and want to submit the stack trace. Email support is not available for me. Where should I sen

I hope this is the right forum for this... I have a 3448P Powerconnect who today began to stop without reason apparent (none which has yet been determined).  I unplug the unit and plug it in again, it comes back to life, but then stops again. To my k

PC 3548p Could not find orders for frames / mtu setting? want to set overall n switch?

In the coming months we will replace our network equipment.  I was able to get their hands on the new gear at the beginning, and if I'm not traditionally a guy from the network, the project has been given to me and I started playing.  The first thing