Linksys Switches

Hello I have a linksys SGE2010P and when I configure and save works well, but after a power off the settings are default return. someone an idea? Rensk,

May switches service nets under different? I work with a company that uses a kit EZXS16W switch 16-port workgroup to which all nodes are connected. I put in a server in a company where I want to isolate 6 of 16 employees who are connected to this swi

Dear all, I was working with my linksys Srw2008p switch and I changed the IP address of the management vlan and somehow, I can't access the web console. I tried to use the new and the old IP. Also, I don't give a name of user and password on my own.

Hi all! I'm having some trouble network at the office and cannot keep close internet for all the world just try a new mode of connection of the cables. We recently received a notice on five new static ip addresses for the office, we did turn on DHCP

I try to upload my switch via Telnet or SSH interface configuration data, but cannot make it work. I have confirmed my server TFTP OK works. The switch is running v1.04 firmware. If I leave the field empty file name I get a response of "unknown error

I have a wired LAN House that needs to be expanded.  I have a Linksys BEFSR41 Cable/DSL router that is currently full.  I need to add more than 2 devices.  I recently bought a workgroup EZXS88W switch.  What I had thought to do running cable line fro

I recently bought a SD2008 (2008/11/28) to replace an older Linksys 10/100 switch for my home network. This switch connects to an ASA 5505 to go to the internet. I have improved since most of my pc have 10/100/1000 and the new NAS I purchased also co

I have a Linksys SLM2008 switch and I am trying to accomplish the following. I want trunk port 1 and do be VLAN 1 but handle traffic for all networks VIRTUAL, ports 2 to 5 shall be allocated to the VLAN104 and only handle traffic VLAN104, 6 to 8 port

As long as I log the LAN port will the company network is there any reason to believe that this model of switch or something like that could cause havoc with a corporate network? Also, is it possible to connect Http in this switch (is there something

Dear Sir. Please tell me how I can bind IP specific with particular port so another ip address cannot work on this port. Please tell me solution for the same as soon as POSSIBLE. Thanks and greetings Chandra Prakash 09829590021

Hello I need to know is there any option to get the ports which some vlan is added with snmp?  I found this oid 17.7.1.4.5.1.1 with snmpwalk. gives information on identifying port and vlan So far so good, but it's the way to see only untagged VLAN on

I try to understand what I have to buy an easy to implement the cable LAN.  Specifily more I'm looking for a router, switch, or hub.  I will be putting this LAN up aboard a commercial ship so it must be wired (too much metal for an efficeint wireless

Hello I would like to know how to send sge2000p log to a file on a win 2003 server. Do I need a software or something else

Hello I have 2 connected sge2000p and create on an aggregation of links. Should I create a lag on the second switch too? Thank you

I have a SLM2008 (SW01) and a SRW2008MP (SW02), these are inter connected both on port g1. G8 SW01 port is connected to the HDSL modem my ISP (off-grid). Connected G2is inside an ASA5505, offering my inside of network port. G7 and g8 SW02 port is con

I have a gigaswitch SR2016 16 port, which has been badly now and again for the past two months. Earlier, I had to reset (pulling on the plug and back in), and then he could run for a while yet. But the last two days, it has been malfunctioning much m

We have sold dozens or even hundreds of SRW2016 16 port switches and a few SRW2048 units.  For the money, they seem like a lot of things, but from a reliability point of view, we are at our wit's end. We're constantly visits on-site to see that all n

Hi, which means '4 slots SFP (miniGBIC) shared"? The slots is itself can be used for a connection at any time? Thank you. Best regards, Daniel Alex

Hi, I'm a new user and struggling for the next step... I have 2 switches SRW224G4P and SRW248G4P. I created VLAN1 and VLAN2 on both switches. In each single switch, VLAN work correctly. But how 2 switch can announce their ports VLAN1 and VLAN2 and wo