NI Hardware

Hello I use an acquisition card NI PCI 1405, camera watec 902 b (RS170 standard). When I purchase, I have horizontal stripes of noise on the image. These bands are make from the bottom to the top of the image during acquisition. In this case, if I us

I was able to find a Port.flx of e/s from reading that allows me to read all 8 bits at a time. I can't find a Port.flx VI e/s writing. How can I write all 8 bits at a time?

Hello I'musing a stepper motor which connected to a NI 9512 drive and I have a forwardlimit and the buttons of the aft limit. I placed a block of line movement in a while loop and logged the error on the error in the registry to offset. Unmanaged whe

Hello I have a problem with the MXI-4 kit / PCI-8331 -C' is a clean install of MAX, using the default installation option. -Win XP 32. The PCI-8331 is the only PCI site in PC With the GUI of MAX does not, plug-and-play detects the jury. If I reboot,

Recently, I was unable to read an analog signal. I use a TBX-68 block attached to a card PCI-MIO-16XE-50.  The signal will be max to everything I put the maximum voltage reading when I hang anything to her.  It will read zero volts with noise when th

Hello I use Simulation Interface Toolkit to target a controller built in Simulink on a PXI target. I used the SIT connection manager to generate the driver screws I had to make some changes in the screw driver specifically Read.vi IO. I made the chan

I'm trying to find the solution of borrowed SMU chassis to the PXI-1 chassis. As I see it in the forums, NI PXI-PCI8332 + PCIe - 8372 OR can make the connection. I wonder another configuration: "PCIe-8362 + PXI8360 + SMU-8360" will work or not? " Ins

Hello I'm sure that this issue has a very simple answer, I can't find what it is.  I'm trying to implement a process of data acquisition on a PXI system.  I use a vi on the host PC to control the DAQ vi on the PXI target.  How to cause the host vi to

Hello I use a PXI-1000 b with two cards DAQ, PXI-6133 and I need to measure the difference in phase between a reference sinusoid, acquired on a map and an acquis of the sinusoid measured on the other card.  So far, my idea is simply to acquire sample

I have a PXI-7358 Controller card and I am looking for a Mini40 of ATI force/torque sensor (Manual: http://www.ati-ia.com/app_content/documents/9610-05-1017%20DAQ.pdf). Force sensor manual said I need to use a data OR M or E-series series capture car

NI PXI-8145 connectivity has suddenly disappeared.  I tried to reset the IP address using the switch NORM/IPRST, but it is still impossible to detect the device.  MAX cannot detect it even if the workstation (PC) detects a network.  Also, USER1 light

That is the problem. I have connected to Umi-7764 and a scientific P70360 drive of the Pacific, the wiring is as follows: UMI-7764-> p70360 J4 terminal screw control IO 26 female pin inhin1 (bar above)-> fault-(PIN 8) inhout1 (top bar)-> enable-(6-pi

Hello I'm relatively new to the use of labview and trying to create an application that reads and writes data in a counter via rs232. I use reading series VISA and VI to write to it. The problem I have is the message that I've read is 6bytes in lengt

I need help to understand how VISA reads from GPIB. By using LabView 8.6, I'm applying to communicate with a customized by using GPIB controller. He is currently working, but I'm not sure of how to use the Enable property of termination. I read of GP

Hello I'm trying to read data from a device connected to the serial port. The instrument makes a row of data, last updated CR LF at pre-set intervals (0.2 seconds, 0.5 sec., etc.). I want to read the most recent line to an interval of time different

I need to read a Gentec electricity meter, the TPM-300. They do not offer a Labview driver for him so I do it myself and I find that the documentation is lacking. I'm trying to communicate via RS - 232 from a computer running XP and Labview 8.6. This

The President complied, I m MA to do my Masters in Karnatak University Dharwad, currently I am working on interfacing with devices using the version of Labview 5.1. In this, I created VI for Micro ohmmeter my Motwane that I m help for interface as we

Hello I used a tilt. Agilent DSO 80404 B, I would like to acquire the trace as represented on l tilt (see figure of the first file oscilloDSO 80404B as an attachment). Pour CELA j use under labview 8.0. Specifications 8000 series labview drivers offe

I use 8 Labview for acquiring data card PXI-5122 (512 MB RAM). Samples using 100Ms rate... Now, I need to acquire samples of 50 M. It takes 400MB size of the file when recording... When I begin to acquire its gives Me the error "Memory full" and site

Hello I just got a 6062E card, and I have a problem with the output analog flaking after that the application runs for awhile. The problem seems to be related to temperature, although 2 AO all channels are only the engine a little less 2 my RMS, 5 sp