NI Products

Cannot install Elvismx on 64-bit windows.

Hi all Have a bit of a crisis. I bought a mydaq for a college project, and can't get elvismx to install. I use a laptop Sony Vaio of 64-bit win 8 and every time elvis tent to install I get the error "32-bit only" and the installation program quits. I

Bouba Analyzer: How to control the number of points per decade?

Total newbie here. I can't control the number of points per decade in the Bode VI. It's always 5 points per decade. Don't know even how to get the Version of Elvis #, but it is at a minimum 4.1, because Elvis installer will install 4.1 (said the curr

How much it might cost to fix an NI Elvis II

Nevermind, I ordered an NI Elvis II + on eBay without power and when I got the power supply (today), the eddd Board does not work.  Well, the best thing I could do was to contact the vendor for the return but the seller did not allow that so I opened

Replacement power supply for NI ELVIS II +.

My diet for NOR Elvis II + has been lost.  I wonder if someone can provide the part number? It will be appreciated. I tried to look in the manual, but I can't find the part number of the power supply or the plug. Anyway, it will be acceptable to use

The use of attenuators with myDAQ

So I try to use an Attenuator (from mini-circuits, BNC 50 ohm) output on the myDAQ for tensions in the microvolt range.  However, rather than mitigate it, the signal of clips instead. I tried a unity gain buffer, but the signal still clips. I used ju

Corriente de Salida en NOR myDAQ

What TR dá sucede an engine has the voltaje fuente of + 15V that requiere mas corriente that only el DAQ you can submit. Puedo danar el device, o only no esa corriente entrega?

Maximum frequency for digital counter input

Hello world to measure the speed of a rotating wheel, US 36 in a disc holes and detect with an optical sensor of rotation. Which means that the maximum speed of the wheel or our optical sensor will output a TTL Signal with a frequency of 3200 Hz. (32

How to get mydaq recognize px309 pressure transducer % 3F

It has only 3 wires instead of the usual 4. They are black, red and white and negative excitement, positive excitement and signal respectively. I plugged the black wires and red to an external power supply, the white wire to the myDAQ HAVE. Then I we

How can I see Elvis II boardID

'NOR ELVIS II pinout description' I know everything"BoardID- these eight lines mean the unique ID of each type of card prototyping by short-circuiting the VCC or GROUND."In my own Council, I connect 5 volts for pinout boardID, but I don't know how I

MyDAQ - generation of a digital signal and display on an analog waveform graph

Hello I use the MyDAQ OR generate a digital waveform with a Frequency adjustable. This is implemented in a program, I already wrote it, which generates a TTL 'like' impulse out of the sound card. I display the result on a graph of analog wave form, a

How to use the kit sensor Bioinstrumentation Vernier with NI ELVIS II and LABview on a CPU?

So I have the NI ELVIS II + and a box full of Bioinstrumentation sensor, including Kit sensors: Analog Proto board connector (s), pressure sensor, hand dynamometer, hand grip monitor heart rate, EKG sensors, Surface temperature probe, among others. I

Error-200022 occurred at DAQmx start Task.vi

Hello I have peripheral cDAQ and 3 modules that nor-9234 connected. My program (see attachment) works correctly with only 2 modules, but does not work with 3 modules. With 3 modules I have this error: "error-200022 occurred at Task.vi DAQmx Start.»  

Cannot combine channels HAVE in a four lanes of two myDAQs

Hello I used the MAX Explorer to add two channels analog input (AI) of myDAQ in a task. It works very well for this. For now I need application of analog input a four lanes, so I get two myDAQs for this. I add both of two channels of the two myDAQs A

diagnostic command set Auto popup error

Hello Anyone know how to prevent ordering of diagnostic auto value error or warning message windows popup? Thank you. M.C.

Read the serial number in LabVIEW of USB-8476 LIN Module

Is it possible to read the serial number of a USB-8476 module in LabVIEW. I am building a system that will use 10 of these modules in a single system and I want to be able to verify this LINX = serial No.: ABC. I'm afraid that a 'user' will disconnec

Associated CCP: cannot read in the 'normal way' a2l file a certain variable while others can I

Hello If it has been validated in someother place please excuse me. Here's my problem. I have an a2l file where I read some variables (characteristics). I use the VI found on measurement and ECU calibration instrument. The used VI is "MC Characterist

NEITHER LS CAN map with SJA1000

Hello I use card PCMCIA 2 of the series low speed CAN with SJA1000 transceiver to communicate with a SHIELD with a transceiver MCP2551. But when I try to communicate with the ECU using CAN Api in LabVIEW it says there is error of the transceiver. Wha

Change in the ID of arbitration with the help of usb-8473

Hello everyone, IAM using USB 8473 Receive messages on CAN Bus. For what Iam using CAN Receive.vi and Net Interface Logging.vi. IAM receiving messages correctly, but I have a problem in arbitration received IDS. If the current arbitration ID is 0 x 1

ORing the arbitration in a cluster to write Net Multi ID

I use image API CAN and want to write several posts on my device.  The pain I feel is my ID of arbitration, it must be of 29 bits instead of 11.  I know that I OR he, but how do you go about it when it is in a cluster.  Please feel free to look at my
« Prev 1 2 3 4 5 6 7 ... 10 Next »