Animated objects does not move until the final destination.

Similar Questions

• My ink carriage does not move to the way to replace the ink cartridges. I think I put the ink in the wrong office

  My ink carriage does not move to the way to replace the ink cartridges. I think I put ink in bad officejet 3830

  Hello! Welcome to the community @Tammy111 HP

  I read your post about the ink carriage being stuck in your Officejet 3830, and I wanted to respond to troubleshoot. Try these steps and if the transport is not yet move to order so that you can access the ink, then your best bet would be to call phone support to see if they can replace the unit for you. I'll leave their details below.

  HP OfficeJet 3830, DeskJet 3830, 5730 printers - an error 'Transport Jam'

  Click on the thumb to below testify my help!

  Click on the "accept as Solution" if I'm you guide to a solution!

  Contact HP:

  Step 1. Open the link: www.hp.com/contacthp/

  Step 2. Enter the product number or select Auto detection

  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.

  Step 4. Scroll down and click on: contact HP options - click Get phone number

  File number and phone number appear

• Save for precedent: the "Attachment" object does not exist in the previous version

  I'm trying to save a very simple VI from LabVIEW 2013 SP1 to LabVIEW 2009 but I get this strange error.  The VI contains only basic ex that are available in all versions of LabVIEW (shift logical AND Select,<=, u8). ="" when="" i="" try="" to="" save="" it="" for="" labview="" 2009,="" it="" gives="" me="" the="" following="">

  Missing object.  The "Attachment" object does not exist in the previous version.

  I thought first of all it had to do with being possessed by a lvclass, but even after that I removed the class (and unplugged from the lvclass) it always gives me this warning.

  When I try to open it with 2009, it will fail to load the schema-block (error 6).

  The next thing I tried was to copy the block diagram for a new VI and re - create the connector pane, but that doesn't change anything.

  Any ideas?

  Maybe "attachment" made reference to an attached comment (the arrow of a free label for an object on the diagram). I don't expect the presence of attached comments to cause a SFPed VI to not open, but it's the only thing I can think of. Try to remove any comment attached to your diagram and SFPing and see if that solved the problem.

• Player media to Smartphones blackBerry does not move to the next song

  I have a few playlists and when I listen to when a song ends he goes to the next song without me clicking next.  The "Auto stop media player when idle" is set to off.  The other thing is the counter which indicates how long the songs are and counties up and down does not move as the song is played.  Verizon did not know and only they me transferred to support RIMM.  She gave me some BS get me the phone is off and I'm in the same place I was supposed to start.  Playlists have been imported into Itunes device using Desktop Manager.  Any suggestion would be appreciated.

  This happened to me the other day... don't know why.

  I did a battery pull and it seemed to fix.

• Case Structure sequence does not move to the next iteration

  Hello

  I am trying to create a multifunction data acquisition and control of a laboratory instrument. As shown in the attached VI, I finally 3 different modes: simple, door double door and GC, each with their own functionality. So far, I worked only on the Mode of the door, so that the rest are empty. However, trying to make the system to wait for the interactions of the user, if the key 'only start door mode', it moves in this case without problem, and if there is no hurry, he waits, bike to the tab control like I want it. However, after execution of the VI with the pressed button, it will not return to the 'Wait' case, he freezes in "aquire" and refuses to return to the case "wait." I'm sorry if this is confusing, I think it will be clear when running highlight is used, it freezes just after the correct number of iterations in the loop for. thank you for your help,.

  <><>

  Normal 0 false false false fr X-NONE X-NONE / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  Hi Eric,.

  I think the sequence works as you want.  When I run it on my computer on my computer he is turned down for the case of waiting as you want.  I don't have to open the VI called single door Pulser.vi and manually, click on the button to stop inside the VI but after doing that it moves to the cae of waiting.  Also, I noticed that you have a constant wired up to the judgment of the outside loop while. This isn't really a good idea because it forces you to use the button abandon.  The button abandon does not stop correctly the VI and could cause other problems.  I suggest you to have a stop button on the front panel somewhere to allow the judgment of the user of VI.

• Dynamic object does not appear at the time specified in the slide.

  @

  Here's my problem: when I insert a bubble in the slide, set it to appear after 5.0 seconds and the display for the rest of the slide, it does not appear at the specified time. HOWEVER, if I move the speech bubble to appear from the BEGINNING of the slide, then it pops up. I thought that maybe I needed to add an effect to make it work, so I chose the thought bubble, and then add an effect of "fly in" and set the time. It will not always appear at a specified time - that if I put it at the beginning of the slide.

  Here's my question: why the smart object (bubble) does not appear at a specific time, but it will appear if I put the time "appear after" at 0 seconds? I also have tried to move this on the timeline and it still shows only at the beginning of the slide.

  
  

  
  

  Thanks much for any help.

  Hello

  I notice that you have a couple of what appear to be objects Button. I have highlighted them in the image below:

  

  Click on each of them and look at their properties. Change the "Timing" the break after is more than 8 seconds.

  See you soon... Rick

• PCI-7730 does not move in the order of driving different directions?

  I have a 7330 motion control card that I'm driving a shaft on both (so never 1 d moves). I need to be able to move in both directions, which is fairly easy to do using a change (modified to include the limits and home) example VI (I think it was the example of 1 d linear motion). To effectively run my stepper motor for my application, in step/direction mode, when moving to the direction of stage negative (for me it is the 'Blue' in my dye laser) I need to overshoot and then come back so that the engine always ends with a movement from the red. I tried several solutions to this problem, including:

  1. in a VI copy/paste on the screws under necessary motion in order, but specify a 'number of steps to move' for the second piece

  2. call the same Subvi sequentially (so rather than a long VI a VI with calls to conduct main proposal sub - VI) with various implementations of delays and sequencing

  The problems I encounter are:

  When using a single move VI (then go one direction up to the complete removal), I can almost always move properly, be it positive or negative direction. Occasionally, and especially when you try to go in a different direction than the previous move, the engine is not. I can watch it on my oscilloscope monitoring steps returned by the engine. The stages of start-up, but about 4 pulses in the VI closes with no error reported (and with the release of that word because, it seems that the program thinks that the move is successful). However, when you use the VI that he calls one way and then the other, I can * never * get the second move (the opposite of the direction) to happen. In 20 years, I even put delays between them in a structure of flat sequence without result. However, I can move one direction, and then immediately the same direction successfully with the same code.

  I can't find a 'free channel' or the ability to set regardless of the behavior of management (for example, direction set out to a negative displacement before the negative move, then reset for a positive move before the move is necessary in fact). It is quite possible, Miss me a crucial part in my VI main motion, but then I think that the repeated movements of single direction would fail more frequently.

  Is there a way to define the direction prior to a move? Or has anyone else encountered this problem and found a solution more "elegant"?

  Thank you!

  A. Berke

  Note: in order to generate enough current to power my motor (it has optically entered remote), I added my own resistance to the stage and the wiring of the direction as they head towards the engine.

  I solved this in case someone else has a similar problem. It turns out that he should be careful with the card ID. It can only be called once (so multiple calls to secondary screws using the same ID Board in a "main" program does not work unless the ID is passed to higher level) in a program.

• ccSvcHst.exe inhibits the CPU at 100% on XP Media Center 2002 (Service Pack 3). PC does not respond until the end of ccSvcHst.exe there domination of 30 to 90 minutes.

  ccSvcHst.exe consumes CPU: (XP Media Center 2002 w/Service Pack 3)

  • PC does not respond, until ccSvcHst.exe completes his domination of CPU from 30 to 90 minutes.
  • Completely consumes 100% CPU AMD Athlon 64 4000 + (4 GB RAM).
  • Has always been a problem with Microsoft Media Center o/s, which has worstened and occurs more frequently.
  • The PC makes it completely useless.
  • Unable to complete the process or decrease its priority.
  • If hardbooted, the ccSvcHst.exe process usually will continue during the restart.
  • Running Norton 360.
  • Please indicate if you need additional information?
  • Thank you in advance with the help of solution (s).  Your help is greatly appreciated!

  ccSvcHst.exe consumes CPU: (XP Media Center 2002 w/Service Pack 3)

  • PC does not respond, until ccSvcHst.exe completes his domination of CPU from 30 to 90 minutes.
  • Completely consumes 100% CPU AMD Athlon 64 4000 + (4 GB RAM).
  • Has always been a problem with Microsoft Media Center o/s, which has worstened and occurs more frequently.
  • The PC makes it completely useless.
  • Unable to complete the process or decrease its priority.
  • If hardbooted, the ccSvcHst.exe process usually will continue during the restart.
  • Running Norton 360.
  • Please indicate if you need additional information?
  • Thank you in advance with the help of solution (s).  Your help is greatly appreciated!

  The list file you most often is a process associated with Norton 360. However, malware is sometimes assumed the names of the legitimate files in order to deceive the end user. Norton is a Devourer of known system and as a result, I wouldn't be surprised to learn that he is a legitimate file in your case. However, I recommend you download, to update and scan with Malwarebytes and Superantispyware, just to be sure. If the scans do not detect the file and the problem persists I would contact Norton or remove Norton making sure to use the tool to uninstall do.

  Malwarebytes.org

  SUPERAntiSpyware.com | Remove malware | Remove spyware - AntiMalware, AntiSpyware, adware!

  Sometimes to decide what battles to fight the toughest battle of all... Visit my forum @ http://repairbotsonline.forumotion.com/forum.htm

• NULL does not move with the tracking data

  I created a track in Mocha AE and copied to the Clipboard.
  Then, I created a Null value in AE and pasted the follow-up data on it.

  However, Null value does not move.
  Any ideas?

  PS I have watch it during the follow-up process, and grooving of X, I created did move/track.

  you have a composition of 54 Minutes here. you are going to restore all 54 minutes with the 54 minutes of elements trained using data from mocha in sequels? I guess that the answer is no. first thing you have to do is on the duration of the shot you want to make your composition. so only you take to mocha and follow your footage.

  so in your example, I guess you should take about 30 seconds, or maybe more? Set the workspace accordingly:

  

  then cut the timespan to duration:

  

  then you should have this:

  

  Ahhh MUCH better. only the length you need. now use the rail in Mocha Ae option. in case of mocha, you will again see the duration of your huge video file:

  

  to keep things organized you can zoom timeline in the / points so that you can see just the graven images and will not get confused by 53.5 minutes of video you don't need. Press here:

  

  now, you will see this - just your images carved

  

  track data, export and when you paste data - make sure that you are on the first image.

  

  Good luck!

• Content does not move with the work plan

  Kind of a matter of newbie, but for some reason any when I try to rearrange work plans most of the content does not move with it.

  How can I change the content to associate with a specific work plan?

  Oh, layers shouldn't matter, unless they are maybe locked.

  Make sure you click on the "Move art with work plan" option when the artboard tool is selected.

  

• When I click to open thunderbird but the e-mail window does not appear until the icon shows the app closed, how to fix this?

  To start thunderbird, I click on the quick start on my toolbar icon, it highlights that if beginner, then a few seconds later, returns to the closed state. No e-mail window never appears on the screen. When I check the Task Manager, thunderbird does not appear in the list of running applications, but one or two processes show running on the Details tab (one first process by clicking on the icon, and then another if I right click and try to open one of the windows in option). I am running Windows 8.1. It worked well earlier in the day, so I have no idea what happened past. Restart the PC does not help the issue. How can I get the windows thunderbird appears on the screen again? If I can't, please send the instructions to backup all the associated email and address profile information so I did not lose anything... then uninstall and reinstall thunderbird and restore all the info related to my current profile. Thank you.

  Thanks for the reply... still not sure what happened, but I ended up uninstalling and reinstalling bird t. Everything is back to normal after that. So your solution can work, but I don't have the chance to try it. My solution, but is not ideal, was effective and the problem was solved.

• pointer does not move in the games full screen

  My pointer do not move in the games when they are full screen on windows 7. In windowed mode, it works but it do not fit with all the games because I can't scroll.

  I've updated all my drivers...

  It's a well known problem with Windows Vista, but it had an impact on many users... seemed random.  Microsoft produced a patch for Vista.

  http://support.Microsoft.com/default.aspx/KB/932653/en-us

  Windows 7 can get a similar fix in time.  In the meantime, it is possible to download the Vista fix & install it via a right click on the Setup file, clicking on properties, then the Compatibility tab and it runs as an application in Vista.

  Nu WinBreak.com - video game Fanblogging

• 17940049 patch does not work until the end.

  DB platform - s390 - Linux - SLES11 - SP2

  APP Tier - Linux x86_64 - SLES11 - SP2

  I applied the patch above but adpatch do not go until the end. The session of adpatch abandoned at the command prompt to step to "generate reports". All the world did this experiment with this specific fix. I met a similar behavior with a patch of PRC ORS - which has then been superceeded by a later version of the patch ORS.

  Thank you

  I wanted to tell rerun adpatch since the beginning (i.e., do not continue with the previous session adpatch).

  Thank you

  Hussein

• play movie clip symbol at the end of the animation, but does not appear in the timeline

  Work in Adobe Flash CS5

  When I play my movie in the Flash file, the animation stops at the end of the timeline, as it should. But when I test the movie, or export it to any film format, it will play an instance of a movie clip symbol that I used in the animation. There is no extra frame in the timeline panel beyond which must be considered to be the last image. Y at - it a setting or something I forgot that could cause this instance of the symbol to play at the end of the animation, without air in the main timeline? This can be corrected?

  your movieclip (or a parent) who plays on the main timeline or is loaded by your swf.  If you load this movieclip (published as a swf file), you can be sure that your movieclip (or a parent) is the culprit.

  Use the movie Explorer to find all instances of your movieclip using the library for this movieclip name.  If that does not reveal the culprit, you have either made a mistake in your search or if you have a movieclip in doubles.

• Mask does not move with the keyframes set

  Hello world

  Although I have been using this forum a couple of years now, I've never felt the need to ask a question, until now that is. First of all, I would like to take this opportunity to thank many of you for giving me the answers so solve my problem until I had to ask. Especially people like Bill Hunt and harm come to mind. Thank you!

  Now to my question. In my project have a key of track matte on top a video with a mask on top of it. A bit like that: '24 Kiefer Sutherland - type' edition. It worked fine for me in other projects. However, in this particular case, I set motion keyframes on the mask but it only begins to move somewhere else later key frames are defined. Pushing forward keyframes as workaround does not give a nice result. No idea what could be the problem here? I'm editting a project of 1920 x 1080 and the mask has the same dimensions. The update for first mentions something on Facebook that I don't care so I don't think a bug is removed with this upgrade and I'm afraid of updates will slow down my work flow (as was the case with the last update of Lightroom for me...)

  I hope that makes sense to any of you.

  Thanks in advance for your help.

  Kind regards

  Sébastien

  PS. If someone wants a screenshot, please explain to me how to do this, because I can't cut and paste here, it seems, and I don't know how Safe a screenshot on my hard drive (without using Powerpoint... awkward...)

  Surprise: I'm also Dutch. And it's a shame.

  But unfortunately we have English.

  You cannot adjust the video in the mask without either skew (which you did by changing the height and width) image or cropping. And the latter is your best option IMO.

  So nest the two clips with the transition.

  Draw a rectangular white in the Titler the same size when the video is supposed to go.

  The value hidden by approach the sequence embedded in the main timeline to track 2

  Add the wanted poster for track 3.

  In the nested sequence itself reduce you the video and the still picture (probably up to 50-60%) but do not uncheck the uniform scale and set the position.

  To get this just the mask on the video down and drop the opacity so you can see what you do, when done to remove or push the eyeball.

  Fact.

  Let me know if it will work for you.