PS4 - Analog controllers sticks question

Similar Questions

• On the NI PCI-6221 fast sampling rate question

  Hi I was wondering if someone can answer a question of sampling rate on this card to PCI-6221 (http://sine.ni.com/nips/cds/view/p/lang/en/nid/14132).

  Especially if I wanted to transmit simultaneously (analog output) and data acquisition (analog input), what is the sample rate max I could use. Kind regards.

  Since the 6221 is multiplexing the analog input, your question for I / simultaneous ao is possible for one channel of the only. If your "simlutaneously" can include delays (e.g., 100us), you may be able to work with several AI channels as well...

  HAVE the multiplexes, workable sample rate given that the total sample (250 kHz) frequency divided by the number of channels that you use. AO is faster than HAVE it, so it does not reduce this number.

  hope this helps,

  Norbert

• Satellite A110-195: network + pci card missing card controller driver

  I installed all the drivers of "http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU", and in the materiel management area, the above controllers have question marks in front of them.

  I also tried to set up a network and failed, probably due to the absence of the network controller. My network card appear to be installed.

  Satellite A110-195 PSAB0

  Hello

  I have a question; How have you installed the drivers Toshiba?
  Did you follow the lines in the installation instructions document that has been also on the page of the Toshiba driver?

  As far as I know that some problems might arise if the drivers are installed in the correct order.
  I recommend you to choose the right drivers and then follow the line guide recommended in the document of Toshiba.

• GGE909 back analog joystick right stick not working not

  I finally got Xpadder to work, right? I can configure the analog sticks and because God knows why, Xpadder does not read my left/right movements with my analog stick right. If anyone can help me solve this problem, it will be very appreciated. PS I tried to calibrate my controller and which failed. :(

  Hi Gavin,

  I suggest you to send the request on Xpadder support forums. They would help you better.

  www.Xpadder.com/Forum4/index.php

  Feel free to get back to us if you have questions about Windows.

• Question about multi analog outputs voltage outfit

  I am programming my NI USB-6008 with V ++.

  Now, I have a question. The unit has 2 analog outputs.

  When I put the "ao0" channel to a certain tension, then stop this task. Start another task, then the string value "ao1" some tension. When I do the second task, ao0 held the voltage set in the first task?

  Thank you.

  Hi Lowsfer-

  Yes, the analog output of AO1 status will remain in the last State it was before the task is stopped.  As long as the device is not reset or the computer is not turned off, the analogue output will maintain the last tension that you specified, regardless of what did the other Ao channel.

  I hope this helps.  Good luck with your application!

• Questions about the synchronization between output and analog input

  Hi all

  I now have a simple task which head a signal voltage (from PXI ao0) on a circuit and then your comments a voltage at the terminals of a component, for example, that one of the resistors in the circuit, through ai0 on PXI. So in this case, the synchronization between analog input and analog output must be made to avoid error of phase shift.

  I tried to build my VI by learning this example: https://decibel.ni.com/content/docs/DOC-3882

  However I have a few questions.

  1. I noticed that there is a merged error fed the "start task" sub VI for the analog output.  What is the point of fusion to mistake?

  2. I enclose my VI (also shown below) for the output voltage. I put my writing of DAQmx Subvi in the while loop so that I can change the voltage while the VI is running.

  

  However, in the example, the author has been reading outside of the loop and before even the start task. What difference will it make?

  3. I have also attached my synchronized VI. I always put the wavegeneration and the DAQmxwrite in the loop. A bulging guard error saying about samples is not available and needs to a higher sampling rate or a longer wait time. What causes this?

  I appreciate that these problems can be solved. Thanks to you all.

  (1) first you need start the task of acquiring, he'll wait for trigger here. And then you start the build task that provides this trigger. If acquisition could trigger and never start.

  (3) you must first write something in the buffer (writing DAQmx), then only you can generate it (Daqmx Start).

  Check Cont Gen tension Wfm - Int Clk - no Regeneration.vi in the help-> examples for example.

• Stupid question? OK to mix 4 GB RAM sticks with 8 GB Ram sticks?

  So, here's the deal. I recently bought a new 8900 XPS.  I was on the HARD drive of 1 TB for a 500 GB SSD.

  Now, I want to increase the RAM. It came with 8 GB (2 x 4 GB sticks). To be absolutely sure that I myself compatible sticks - I bought some sticks of 2 x 8 GB from Dell.  My machine has 4 slots, so I can have 4 sticks...

  My Question is: can I use all 4 sticks (2 x 4 GB) and 2 x 8 GB, or a mixture of weight will screw something?

  Thanks for all the advice!

  Yes make sure you keep the corresponding paired sticks of correspondence between slot machines. or in other words, put two 4GB sticks in slots of whites and the two 8 GB sticks in the black sites. (or vice versa).

  You can consider diagnostics from built-in running after installing memory memory.

• Question of law activation key sticker.

  Okay, so I have a unique problem. The company I work for asked me with the redesign of several computers. All of these computers are distributed by a company called Nexlink, which is no longer, we do business with. Many of these computers in XP, but despite this, they have Windows activation code stickers on the case for other versions of Windows (some Vista and W7 a few). I have no idea why it's that way.

  My question is, is it legal for me to use these codes if they work? These computers are specced for W7 and XP end support, it would make my job a lot easier if they were running a more modern operating system.

  Okay, so I have a unique problem. The company I work for asked me with the redesign of several computers. All of these computers are distributed by a company called Nexlink, which is no longer, we do business with. Many of these computers in XP, but despite this, they have Windows activation code stickers on the case for other versions of Windows (some Vista and W7 a few). I have no idea why it's that way.

  My question is, is it legal for me to use these codes if they work? These computers are specced for W7 and XP end support, it would make my job a lot easier if they were running a more modern operating system.

  Your company likely took the demotion available with these systems right. If the COA sticker list Windows Vista Enterprise or Windows 7 Professional, they can be downgraded to Windows XP Professional for compatibility or standardization on an image of the company to facilitate their deployment.

  If you have access to reinstall media of Windows Vista Business or Windows 7 Professional, Yes, you can use the product key to upgrade to the edition in question appearing on the certificate of authenticity.

• 2 questions: why are there no "forum" for Ad Premiere ELEMENTS? And: HOW to EXPORT (with Prem 13,00) to COMPUTER VIDEOMATERIAL WITHOUT ANY LOSS OF the ORIGINAL DV or ANALOG VIDEO-QUALITY (inasmuch as I get - to start - an endresult SMALLER!)

  2 questions: why are there no "forum" for Ad Premiere ELEMENTS? And: HOW to EXPORT (with Prem 13,00) FOR COMPUTER VIDEOMATERIAL WITHOUT LOSS OF the ORIGINAL DV or ANALOG VIDEO-QUALITY (inasmuch as I get - to start - an endresult SMALLER!)

  Thank you, Ann. I'll move it.

  Kind regards

  Kevin

• Satellite A300-20n - memory stick pro duo question

  Help people!

  When I put the memory stick sony pro duo in 5 in 1 reader and try to upload photos, I get the message:
  The disk in drive F is not formatted. Want to format it now? Yes / No...

  Nothing happens if I press Yes or no... any body has any experience?

  Thanx

  Hello

  As far as I know the card reader supports Memory Stick Pro, but it does not support the MS Pro Duo cards.

  Please see the user manual.
  You will find an info what cards are supported.

  You can use the maps:
  SD, SDHC, MS, MS Pro, MMC and xD

• Question related to the entrance with pci 6221 and SCC 68 analog

  I use 6221 PCI and SCC 68 analog read of voltage between the terminals of the drain and the source of a transistor. The drain is at 0 Volt and source is connected to 5 volts via a 100 k resistor. The transistor is used as a follower of the source, and therefore the output is measured at the source of the Terminal. When I measure the voltage by using oscilloscope, I see clearly the change of output as a result of change of voltage of the door. But, when I try to acquire the same by using labview, I see nothing. I tried to change the signal to the CSR, NRSE, but nothing works. Seems to be that something related to differences in impedance. Can you please advice me on this issue? Thanks in advance

  Hi rsd111,

  I understand that you measure a circuit similar to this ( http://en.wikipedia.org/wiki/Common_drain)

  I also get that you use an external power supply with GND connected to the Drain and - 5V connected to the Source with a 100 k resistor.

  You should be able to measure the tension between D and S setup a differential measurement and connection Ai0 + D and Ai0 - s, in fact you can youse Ain you prefer.

  You should be able to do the same measure also at configuration NRSE linking Ai0 AiSense at the Source and drain.

  The Board's input impedance is greater than 10GOhm, it must behave as the oscilloscope in pairing mode high-impedance DC.

  6221 specifications: http://digital.ni.com/manuals.nsf/websearch/8117DF4C5A29C95C862573020061023B

  Nice day.

• NI USB - 6259 BNC DAQ: analog input signal cross on the question

  Hello

  I use the NI USB-6259 BNC DAQ unit to acquire a four-channel analog signal, and I'm having a problem with a signal that affect others. The circuit, I am running is:

  I have a wire connected to a battery (two AA batteries at ~1.5V), which then feeds the signal cable to a BNC cable, which feeds an analog BNC of data acquisition channel. The field of NBC feeds to another wire, which is attached to a conductive plate.  The idea is this: when I touch the wire connected to the battery for the metal plate, I complete the circuit and thus get a binary not anything at all about 3V.  When I tested with an osciloscope using two channels (each earth connection to the metal plate) I get independent steps whenever I touch any of the sons of the respective batteries to the metal plate (i.e. it works as expected).  However, when I use it with data acquisition, whenever I touch a wire, I get a response in all other channels (3 others), even if their respective sons does not touch the metal plate.

  No one knows why this happens, and how I might be able to stop this 'cross-talk '?

  Thank you

  Veritas

  I see, and you're right.  This request will have trouble with crosstalk.  Luckily the ground channel thing should help you.

  Configure your DAQ to collect twice as many channels as you need.  Connect your wires in the odd channels and short circuit (ground) the entries of those even.

  Now when you scan the channels it will always technically crosstalk, but it will come from a channel to the ground so that there will be nothing to interfere with your measurements.

  At least that's the theory.

• get the question mark yellow by raid controllers and audio multimedia

  i ' am receives no sound media player

  Hi gerard 880,.
   
  -Remember to make changes to your computer once you have stopped receiving sounds?
   
  Download and install the latest drivers for the audio device from the manufacturer site to solve this problem.
   
  Device Manager displays a list of all devices that are installed on a Windows XP computer. When you view device information in Device Manager, you may see a device listed as unknown device next to a yellow question mark. It can be difficult to determine the cause of this unknown device, because there is little evidence that it generates.
   
  This article explains possible reasons that an unknown device may appear in Device Manager.
   
  How to troubleshoot unknown devices listed in Device Manager in Windows XP
   
  Additional reference on:
  Troubleshooting of conflict of devices with Device Manager

• Stupid question of the Stick wireless about Photos

  I have successfully connected to the device so that it communicates with my Iphone 6. I transferred photos from my Iphone on the joystick (copied) successfully wireless via WIFI.

  My question is, manually delete the photos on my Iphone in order to make room? Or y at - it an option to automatically delete after the /copy transfer operation?

  Also, the transferred files are uncompressed copies and 100% of the Iphone?

  Thanks in advance.

  If you manually transfer the pictures, you need to remove manually your native photo app after the transfer to free up space.

  in the settings there is an option for backup camera. If you use this option the camera will automatically backup whenever the application is started. This option also includes an option to remove images after backup.

  If you choose to delete the images deleted after backup will be in the recently removed from your application folder native photos for 30 days. If you need to free space immediately, you must open the native photo app and manually delete the pictures in the folder recently deleted to free up space.

  the files are exact copies of the jpegs that takes the iOS device. These are not compressed as all JPEG files are compressed. iOS devices (until the iPhone 7) does not in the first.

• Questions of Compaq Presario CQ60 with restore settings factory, sticked on a blue screen (BSOD, no)

  Hello, I have to get my usual laptop fixed, so I decided to get out of my Presario CQ60, which I have not used in 4-5 years. The operating system is Windows Vista Basic and I want to perform a restore factory settings (I don't mind losing the data on it) and upgrade to Windows 7 Home Premium. So far I tried to do a restore to factory settings by pressing F11 several times to start, and I get to a screen that says "Windows loading files", which leads to a black screen. After what seems like a long time, a blue screen appears where I have control of my cursor (not the Blue Screen of Death) and nothing has changed since. I will update with any changes, because things seem to happen after letting it go for a while, but for now any suggestions on what to do? Let me know if I've left out any information. Thank you!

  Hello

  We can not help you with this problem of factory settings.

  Press F11 at STARTUP is the method that HP plans to use.

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c00809678#n405

  1. Turn off the computer if it is not already turned off.
  2. Disconnect any external devices such as printers, USB drives and memory cards.
  3. Turn on the computer and immediately press the F11 key several times , about once a second, until the Recovery Manager opens.
  4. In the Recovery Manager welcome screen, click Next .
  5. On the Microsoft System Restore screen, select No , and then click Next .
  6. On the System Recovery screen, select Yes , and then click Next to continue the recovery process.

  etc.

  And that is the recovery Partition and the process which they installed during the manufacturing process, not Microsoft HP

  You will need to contact HP or ask questions in the forums to Support HP about this problem.

  http://h30434.www3.HP.com/

  @@@@@@@@@@@@@@@@@@@@@@@@

  And I don't think that it will be suitable for the upgrade to Windows 7 Home Premium as being Vista Basic, the material it will not suitable or sufficient to run Windows 7 properly and I have no idea if HP even wrote Windows 7 drivers for it.

  Before you buy Windows 7 after Vista fixed:

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Windows 7 upgrade paths:

  http://TechNet.Microsoft.com/en-us/library/dd772579 (v = ws.10) .aspx

  «Installation and reinstallation of Windows 7»

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  See you soon.