Why my DVD does not start with the film and not on the menu?

Similar Questions

• Why my computer won't start with the DDR RAM?

  eMachines T5026 Memory Specifications Standard memory 512 MB (removable) Maximum memory 4. 0 GB Memory expansion 4 Sockets Memory comments PC2700 DDR SDRAM DIMM. Supports Dual Channel DDR. Type of processor Processor Intel Pentium 4 519 3.06GHz Model comments Bus 533 MHz, Intel 915GV Chipset front

  Upgrade memory for eMachines eMachines T5026 computer, eMachines eMachines T5026 computer takes the PC2700 DDR SDRAM DIMM. Supports Dual Channel DDR. Type of memory and is installed with 512 MB (removable) of memory. You can upgrade your eMachines computer eMachines T5026 for up to 4.0 GB memory, the system has 4 sockets to install memory, already with 512 MB (removable) standard memory installed. For best performance of the computer, use the maximum amount of memory allowed per slot for your computer. Choose the following memory Upgrade for eMachines computer eMachines T5026.

   

  I am running Windows XP SP3 with RAM sticks of 256 MB (2) on an old eMachines T5026 desk top.  I added strips of RAM 1.0 GB (2) for the two slots open and computer would not start.  I tried with stick (1) 1 G and (2) 1 sticks and it still won't start.  I tried to mix and match the 256 with 1 G in each combimation, but it does not start.  Won't start with one or two sticks of 256.  Best Buy had PC3200 DDR RAM but the spec above States use PC2700.  Geek Squad says that PC3200 is OK instead of PC2700.  Is this the problem or I had to do something besides just insert new RAM?   Suggestions welcome.  Thank you.

  Thank you for confirming that. I still think that the above tips are relevant:

  Because what you bought doesn't work, my suggestion is to stay within the plug (PC2700), like this:

  http://www.crucial.com/store/listparts.aspx?model=T5026&cat=RAM

• The CD/DVD does not work with El Capitan 10.11.5 on Macbook Pro

  Hello everyone, I spent the time to research on the here and the other site on why the CD/DVD does not work with El Capitan 10.11.5 on MacBook Pro mid 2009. This discussion forum has said that he will not work with the El Capitan software. Any idea or suggestion? Back to Marverick or Yosemite? I tried to use SMC reset, restart, recovery and still the same issue.

  I thank in advance.

  ~ Mike

  I have my doubts that the (10.11.5) software is the problem.  Are you sure that the DVD player is simply not defective?  Have you tried to clean the lens?  What is the State of the disc?

  Your best option may be a date at a bar in engineering of the Apple store for a FREE evaluation.

  Ciao.

• Why Tecra A3 does not start from CD/DVD?

  My laptop Tecra A3 does not react to the BIOS setting asking at the start of the CD/DVD.

  CD/DVD is the first place in the list of bootable devices (defined through F12 in boot sequence) the operating system starts with the HD. I have a chance to start with a bootable CD!

  The configuration is the following:

  Tip: TOSHIBA EAT10/EAT20
  BIOS: TOSHIBA V2.80 10/25/2006

  Any advice is welcome!

  Thanks in advance

  Antonio Giarrusso

  Have you tested with different CD bootable?
  Also try to start computer laptop using F12 and choose ODD as the first boot device.

  You can use ODD in Windows OS preinstalled?

• I try to enter the serial number to register my software, but the label outside of the box, he's starting with the letters and it does not accept the letters... . Only numbers

  I try to enter the serial number to register my software, but the label outside of the box, he's starting with the letters and it does not accept the letters... . Only numbers

  Serial numbers contain no letters, so maybe it's your redemption code, for use on adobe.com to get your serial number.

  Here are a few links to look for more information

  https://helpx.Adobe.com/x-productkb/global/redemption-code-help.html#productboxorprepaidca rd

  Quickly find your serial number

• Why my printer does not print with Windows 8?

  Why my printer does not print with Windows 8?

  Did you just upgraded or purchased a new computer with Windows 8, and now you can't get your printer to work?  If so, this can help you.  Many people have questions about the installation of their printer on a new OS.  This will help you answer these questions and make sure you get everything installed.

  Before you start

  Before you try to install the printer on a Windows 8, you should check to make sure that the printer is compatible with the new OS.  The link below will give you a list of printers that will work in Windows 8.

  http://support.HP.com/us-en/document/c03168175

  If you have upgraded your computer to Windows 8 formed another version of Windows, make sure all software uninstall complete of your printer.  It should still print, but to use all the features, you will need to reinstall the software, if available.

  Another thing to consider is how you want to connect the printer to the computer.

  1. USB.  You must ensure that you have a USB cable which does not exceed 6 feet (about 2 m).  Be sure to connect the printer directly to the computer.  Do not use a USB hub.
  
  
  2. Ethernet cable.  Make sure you have the network configuration, you have a free cable port on the router, and you have an available Ethernet cable.
  
  
  3. Wireless.  You must ensure that you have the configuration of the wireless network, and you have the password of the wireless network.

  1. installation Via USB

  Installation via USB in Windows 8 became much simpler for users of HP printer.  In other versions of the Windows operating system, you need to launch the installation and wait that it asks for the USB connection.  If you do not, you will need to uninstall the printer from the devices and printers folder and then launch the installation.  In Windows 8, which won't be a problem.  If you plug the USB cable from the printer and then install the printer software, work remains.  Now for in depth instructions on installing the printer via the USB port click on the link below.

  http://support.HP.com/us-en/document/c03521864

  2 installation Via an Ethernet network connection

  For an Ethernet connected printer, the installation is disconcerting.  All you have to do is to connect the printer to the network.  Once you have done so, Windows 8 will automatically install the drivers for you.  Then, all you have to do is install the rest of the software, if available.  It's really as simple as that.

  http://WWW8.HP.com/us/en/support-drivers.html

  3 installation Via a wireless network connection.

  For a wireless printer, network installation is disconcerting.  All you have to do is to connect the printer to the network.  Once you have done so, Windows 8 will automatically install the drivers for you.  Then, all you have to do is install the rest of the software, if available.  It is roughly the same as just Wireless Ethernet installation.

  http://WWW8.HP.com/us/en/support-drivers.html

  Alternative installation methods

  With Windows 8, the drivers of many printers are installed with the operating system.  These are called pilots InOS, since they come built-in to the operating system.  If you have one of these printers, you should have to do simply connect it to the computer via USB, or connect to the network via Ethernet or wireless.  Once you have that makes Windows will take care of the rest.  There are other methods of installation of your printer if normal methods don't work for some reason any.  You can install the printer is using the printer, or through Windows Updates Setup Wizard.

  Set printer wizard:

  http://support.HP.com/us-en/document/c02681060

  Windows Update:

  http://support.HP.com/us-en/document/c03460648

  Note: The drivers of Laserjet for the Asia-Pacific and the Japan will come only at a later date.  See below the link support site for the availability of the driver.  I will update this post once they become available.

  http://WWW8.HP.com/us/en/support-drivers.html

  Hope that answers some questions.

• Windows 7 x 64 installation DVD does not start on a Dell XPS One 2710

  I apologize in advance for the long post...

  Just got a Dell XPS One 2710.  Lot has happened, but let me clarify the current number as briefly as possible: the machine does not start from the HARD internal disk or the Windows 7 Installer x 64 DVD.  He gets through loading files and then gray progress bar when its colorful animation it blue screens with error CACHE_MANAGER.

  I ran the diagnostic, including tests extended memory tests, and they have not found any error in what either.

  When I was troubleshooting this problem previously, in some sort the motherboard got bricks (I don't know what exactly I did to cause that), but Dell has since replaced.  The first motherboard had BIOS version A09.  It has installed A11.

  I can't find any BIOS settings combination that will allow even the Installer Windows DVD to start with the Blue error screen CACHE_MANAGER.  I tried the UEFI boot modes and legacy, I tried RAID and AHCI.  I tried with and without loading legacy OPROMs.

  What I ultimately do is set the start mode of RAID so that I can use the SSD mSATA as a cache ("Accelerate" in the Intel RST Panel).  But I can not even the installer to start on where I can load drivers RST (assuming it's even necessary).

  Other posts have suggested problems with memory, but I took each of the two DIMMS one at a time and I always had the same problem.

  Should I suspect the hard drive?  When we arrived at the machine, he seemed to be running Windows 8 very well - until we went on the way to the side dark and downgraded to Windows 7.  Then once we started to have errors on updates, things has quickly degenerated from there.  In addition, again, diagnoses don't find any problems.

  Any suggestions on how to get at least this puppy to start?   .. .or what have we done wrong?

  Thanks EJN.  It turns out that there is certainly a hardware problem on this machine.  It was a refurbished Dell making machine and apparently when they renovated the it, they missed the real problem.

  The way I know that it is material, it's that we bought actually 2 of them at the same time.  When I started to suspect the material, I decided to try this process on the other.  He worked like a knife through hot butter.  But I will say that the combination of the BIOS set to boot legacy mode and still start the installation with the option to UEFI DVD in the start menu was not easy to understand at first.  But when I followed the correct steps, everything worked very well.

  For those of you who might try this, here are a few things I learned along the way:

  1. According to EJN, take the time to get/burn a CD to install Windows 7 x 64 that already has SP1 on it.  If you go to preserve the UEFI partitions and the boot hard disk, you must have x 64.  x 86 (32-bit) does not support UEFI.

  2 unzip the RAID drivers to the * root * your USB flash or floppy drive and have it in the machine when you start the installation DVD.  I could be wrong, but it seemed to me that the installer looked for them without having to explicitly say it loads the me.

  3. as said EJN, set your BIOS boot legacy mode but use F12 at startup to bring up the Windows Boot Manager and start the installation in UEFI boot mode DVD.  If you want to implement an SSD as cache for your hard disk, you will need to set the SATA controller in RAID mode.

  4. I had partitions UEFI and was able to leave them intact.  Here's a very brief explanation: http://technet.microsoft.com/en-us/library/dd744301%28v=ws.10%29.aspx your results may vary.

  5 take this one as a possible suggestion that is worth what you pay for it: when I got the USB with RAID drivers at the root before starting the installation DVD, I didn't need to load the drivers explicitly.  As I said, it seems that the installation program has been smart enough to find and load what it takes, but honestly, I don't know.  When I load them explicitly, I got errors saying that the installer could not install on the partition, I had chosen.  Makes me think that I could have loaded both times.  What worked for me was NOT explicitly their cargo.

  6. you MUST be at your PC when Setup has completed copy and unpack the installation files.  Don't forget that you have your BIOS set to start legacy mode.  So when he tries to restart to complete the installation, it will try to start using the table inherited from on your hard disk - who is not here because you did a UEFI installation with partitions for UEFI.  So when Setup restarts the first time, you might as well get into the BIOS here and choose the UEFI boot mode.  If you do not, you will need to grab it whenever it restarts using F12 and manually tell it to boot from your hard drive using the UEFI.

  These steps, you should get installed and running.  But another thing I had to understand that when first, I installed and executed the dashboad Intel RST, there is no acceleration option even if my mSATA SSD was found healthy.  I found that if it is formatted and partitioned, you actually go into Disk Manager and delete the partition before the RST dashboard he sees as available for use as a cache.

  I hope this helps others out of me.  It's a heck of a lot easier when the hardware is not bad!

• Windows 7 - DVD does not read the disk on the computer.

  My DVD does not read discs, when I click ion DVD player on my desktop shows insert a disk me error help

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://Club.myce.com/F61/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Why pes 2012 does not work with me and my video card is 1699 MB Intel HD Graphics(core i3)?

  Why pes 2012 does not work with me and my video card is 1699 MB Intel HD Graphics(core i3)?

  Hello

  You receive an error message?
  
  Method 1:
  You can update the drivers of graphics cards and check.
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  
  Method 2:
  You can also perform a clean boot and check if it works:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: after a repair, be sure to set the computer to start as usual as mentioned in step 7 in the Knowledge Base article

  You can also check out the link:
  The problems of the game performance
  http://Windows.Microsoft.com/en-us/Windows7/fixing-game-performance-problems
  Diagnose problems running DirectX
  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-basic-problems-with-DirectX

• Why this scriipt does not work with Firefox? &lt; embed src = "News2008Fall.pdf" width = '615' height = '3200' &gt; &lt; / embed &gt; "

  Please tell me why this script does not work with Firefox. It works with Safari. Here is the page that includes the script: www.lionsgatehoa.org/newslettertest.html. Thank you. Tom Engleman

  Here's the script in my html document:

  < embed src = "News2008Fall.pdf" width = '615' height = '3200' > < / embed > "

  Edit: removed # phone

  Works for me on Linux.
  
  Your system details list does not display the Adobe Reader plugin, so you'll have to (re) install this program.

  See:

  • https://support.Mozilla.org/KB/using+the+Adobe+Reader+plugin+with+Firefox
  • http://KB.mozillazine.org/Adobe_Reader
  • http://get.Adobe.com/reader/otherversions/

• CD/DVD does not recognize the drive.

  CD/DVD does not recognize the drive.  Error message-"Insert a disk." "" "Insert a disk in the drive (E or F, depending on whether one in use).  I bought a DVD/CD thought exteranl today that might work.  Same error message with the external dvd/cd.  Can hear the disc turning when it is inserted during a short period of time, maybe 20 seconds, then it stops.  Sometimes, the disc is ejected when the error message appears, sometimes not.  Same results even with blank CDs.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Why CRYSTAL_REPORT program does not work with windows Vista? __

  Why CRYSTAL_REPORT program does not work with windows Vista?

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  Windows Vista Compatibility Center

  First thing to do is to check its Vista compatibility at the link above, and if not to see what patches/solutions are available from its manufacturer...

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  If this is not Vista compatible, read the info on the link above.
  It works for some programs, but not all.

  This applies to software programs, NOT hardware drivers.

  If it's Vista compatible > uninstall it > Re-download/save to your desktop > right click on the setup.exe > run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• Why lately company does not release smartphones with screens 4 inches?

  Good evening!

  Why lately company does not release smartphones with screens 4 inches? Me as a person with small hands, it is very difficult to work with models even 4.3 inches.

  Now, I have Sony Xperia P. Very comfortable: fit to display me size metal case. Everything is fine except for the inserts in plastic (lower part). Shabby paint with these pads. Now, the phone looks not very nice. So I thought to change towards a new model. Because the phone close to 3 years.

  Expected to soon release a smartphone with a diagonal of 4 inches? (And in a metal box).
  Thanks in advance for your answer.

  Hi Valeria! You can share your suggestions on the Sony Mobile community here. Thank you!

  If my post answered your question, please mark it as "accept as a Solution.

• Why my iMac does not recognize my scanner 1600 epson perfection since the upgrade to ElCapitan 10.11.4?

  Why my iMac does not recognize my scanner Epson Perfection 1600 since the upgrade to ElCapitan 10.11.4?

  First try this: reset the printing on your Mac - Apple Support System

  If this fails, you can try this driver: http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=14577 & infoType = Down load

  

• IRQL not less equal or (bsod) after doing some tinkering with the registry of Windows Media Player files.

  Original title: IRQL NOT or LESS EQUAL (BSOD) help

  Hello

  I've experienced this * IRQL NOT LESS or EQUAL * problem irregularly from January 2. It happened after doing some tinkering with the registry of Windows Media Player files (but I made sure to return to the default options once I'm done and I have also provided a backup copy) since it generates random album art files and I am looking for a way to stop him. I also deleted the files Windows Media Library (wmdb). I don't know if this has nothing to do with the BSOD. This error occurred at random intervals, sometimes after opening my computer laptop it will BSOD sometimes, it won't happen after long operating hours. Hope you can help me with this.

  Is attached a copy of my DMP files which you seem to demand for troubleshooting. Dump

  These accidents were related to the corruption of memory (probably caused by a driver).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You don't need to run memtest again unless the auditor is not the cause, or you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)