5.2 ACS is not authorization policies

Similar Questions

• Secondary ACS do not authenticate

  I have 2 ACS 1113 devices running 4.1 Build 24 (1). The first is the main and replica nightly on the secondary to our DR. Although in different places, they are both in the same VLAN with no. firewalls or an in-between of the lists to access them. All my devices will be authenticate with my primary ACS unless it is down, in which case they must authenticate the ACS secondary. The problem is that I have no problem with authentication on my ACS primary, but I can't get anything to authenticate to my high school (after the primary decision-making down to test). In trying to authenticate to my high school, I get no newspaper for authentication successful or failed after that my attempts fail. In addition, during my attempts fail, I try to log into devices locally and my authorization fails - again with no journal of the ACS. However, when I remove the NDG in the ACS secondary, I'm able to log on locally on the network device.

  I believe that with the device the NDG in the breast of the CSA, there is a communication omitting my attempts (although it does not connect anything) since I can take the device off that NDG and transmit local authentication. I was running code 4.0 with the same question and thought that the update should fix the problem... but obviously, I have something to do else here.

  Any comments or suggestions would be greatly appreciated.

  This on seconday acs.

  ACS---> configuration network ===> table Proxy Dis---> click default ===> if you see delivenrance 1 to the aaa Server---> drag it to 'Prior to'---> and what is there under forward to---> Drag it server aaa--> submit + apply.

  It should work now.

  If you do not see distribution proxy option then go to GBA--->---> advanced option interface configuration---> enable the distributed array.

  That should fix it.

  Kind regards

  ~ JG

  Note the useful messages

• 5.2 ACS does not check the Active directory changes

  Hi all

  I work with ACS 5.2 and using Radius Authentication client vpn.

  The authentication method used is Active Directory in a Windows environment with multiple domains in the same forest.

  My problem occurs when I change from one group to the other user in Active Directory. After that, I get the following message appears when try to connect:

  15039 selected authorization profile is DenyAccess

  The message is as correspond to the default policy.

  Another user in the same ad group works very well.

  All domains in the forest have a relationship of trust between them.

  I use universal groups to include all domain users belongs to this forest.

  Can someone help me?

  Concerning

  What is your rule of authentication corresponding against a single ad group?

  You can check which groups were extracted for the user, as follows:

  -goto "monitoring and troubleshooting.

  -Select authentication - RADIUS - today

  -Find the input that do not match and click on the Details icon

  -Expand the section "Details of authentication". Look under "Other attributes" groups comes from AD to be enrolled in the user

• Access to the network-> ACS 5.4 authorization profiles

  Hello

  For ACS 5.4:

  In-> authorization of network access profiles, there is an access profile allow it. If you try to change it to the top of the POPs a message that says:

  "The profile you have selected is reserved and cannot be deleted or changed.

  Nobody knows what this profile contains in its base of rules? If I wanted to create a similar profile what common tasks or attributes Radius would I use? The same would go for a profile to deny access. No one knows what it would look like?

  I looked at common tasks and the Radius attributes for the new profile, and it seems not very intuitive.

  Thank you

  Jim

  Authorization profiles are used to define the RADIUS attributes to return in an Access-Accept

  The permitted access profile contains no attributes at all and is actually an empty response. You can create an equivalent profile by simply giving it a name and no other attributes.

  Common tasks and the RADIUS attributes are the two ways to set the attributes to return:

  -Normal: provide an abstraction of seizure/selection of the use-specific RADIUS attributes and values are entered when using

  -RADIUS attributes. manually enter the however, attributes, and its value

  There is only one profile predefined for DenyAccess that issues a rejection of access and can not be created manually

• ACS 5.2 authorization policy

  Hello

  is there a method to control access to the WLAN (PEAP) different on the same ACS 5.2 and WLC?

  In other words, ago 14:00 one of the groups have access to the domain network only the other group only have access to the internet
  and maybe a third group with access to both networks.

  Currently if I add new authorization policy, the user will have access to two networks...

  Thank you, in advance.

  Yes HRT is possible, the ssid is transported in the station id called which is an av pair sent in the access-request packet. The called-station-id format is, so you can combine this with the AD1:ExternalGroups and assign the result of access permit or deny access depending on your implementation, you can build your strategy for leave to a compound affection of "called-station-id ends with ssid". Also, the ssid is case-sensitive when acs makes its decision so keep that in mind.

  If you look at the ACS authentication report, you can see the ssid that I am referring to the id of the station called the newspaper.

  Hope that helps

  Tarik Admani
  * Please note the useful messages *.

• 5.3 - command sets ACS does not

  We installed Vmware-cent os 5.3 GBA and a cisco router is configured to authenticate to this server GANYMEDE +,.

  I am able to connect to the router using the username specified of GANYMEDE. / password and able to see shots also like below in the policy,.

  But the sets of commands work as defined, pls help me to find the problem...

  Filter:

  StatusNameIdentity GroupNDG:LocationNDG:Device TypeTime and DateCommand SetsShell ProfileHit heads

  Match if:

  Equals EqualsNot

  EnabledDisabledMonitor only

  		Status	Name	Conditions				Results		Hit Count
  				Membership group	NDG:Location	Type of NDG:Device	Time And Date	Command Sets	Shell Profile

  1			ACCESS TO RO	in all groups: READ ONLY ACCESS	in all locations	in all Types of devices	-ANY-	READ ONLY POLICY	SHELL OF RO	10
  2			RESTRICTED ACCESS	in all groups: ACCESS SELECT	in all locations	in all Types of devices	-ANY-	RESTRICTED USER POLICY	Allow access	1
  3			SUPER ADMIN ACCESS	in all groups: FULL ACCESS	in all locations	in all Types of devices	-ANY-	ALLOW ALL POLICIES	Allow access	0

  How you set up your sets of commands? Also make sure that we have orders for authorization on the router,

  AAA authorization exec default group Ganymede + authenticated if

  AAA authorization commands 1 default group Ganymede + authenticated if

  AAA authorization commands 15 default group Ganymede + authenticated if

  AAA authorization config-commands

  Kind regards

  ~ JG

  Note the useful messages

• ACS - configure the authorization of shell commands to work under the configuration mode (conf t)

  Hello world

  I'm trying to set up a shell commnds set orders (including t conf mode) will be allowed, with the exception of administrative commands, such as writing, copy, admin, format etc.

  He worked for the commands in privileged mode (most) (such as writing and copy), but did not order t conf mode. It is important to prevent users to perform the ' write for the "and" copy run start "commands, for example.

  Here is the entry in the series of command shell (Partial_access) approval:

  Unmatched orders: permit

  List of commands:

  Admin

  copy

  delete

  do

  format

  To write

  (Relevant) group settings:

  V - shell (exec)

  Privilege level of V - 15

  Shell command authorization set

  Assign permission to command Shell Set to any device network - Partial_access (group name)

  I use CiscoSecure ACS version 4.2 (0)

  Thank you

  Lior

  Hi Lior,

  Please make sure you typed in the AAA client, the following commands: -.

  AAA authorization config-commands

  Thanks for posting your AAA client configuration via "run sh |" I have aaa "and if possible your configuration of privilege"

  HTH

• Help ACS shell command authorization

  Hello

  I wanted to only allow users to use the command interface. But when I have enabled terminal config of ACS shell command, all commands are allowed. How can I limited users having only permission for command interfaces?

  Thank you

  Two things may be wrong

  (1) you do not have the following command on your AAA Client:

  AAA authorization config-commands

  (2) you have clicked on the 'unmatched orders' = allowed radio option in ACS, take a look on:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml

  Concerning

  Farrukh

• ACS: How to import policies?

  Hello world

  ACS 5.8 added the ability to export policies to a repository, and yet I have not seen any interface to import these policies in ACS. In addition, they are exported encrypted that makes them unreadable from the point of view audit. No chance, they can be decrypted outside GBA?

  Have a good weekend :)

  Hello

  Don't we have policies to support bundle? Yet once access security policy will cause more damage than of any unauthorized access to support bundle.

  To add this feature, you must contact your Cisco account team and they will be addressed later, but chances are you'll hear the same thing.

  Kind regards

  ~ JG

• What can I do when I'm there on the permissions in the top bar I get yahoo search results and not Authorization Manager.

  I'm putting my authorization manager info, but when I put on the permissions in the top box I have yahoo results research and authorization manager is not started. How can I get another way to authorization manager? Or how to get the address bar to work as it should? I look forward to a response.

  Enter Subject: authorizations in the URL/address bar. (Requires the colon and no space)

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

• 3.3 ACS will not save button

  In the last few weeks I had a problem in ACS 3.3 when you add a new device.  When checking I can connect the device using GANYMEDE, I get an error of key shift in newspapers having failed the FAC.  When I look at the device key is missing.  I add the key and submit it. Sometimes it works, but most of the time, it takes several attempts to get the key to save.  Now, recently the devices that have been years GBA begin to lose the key.  I've looked everywhere and have not been able to find an answer.  I'm migrating to ACS 5.2 but it will be a few weeks before I was ready to cut more and should be able to use the ACS 3.3.

  Thanks for any help.

  You use Firefox. I had the same problem. I now use ietab in firefox or Internet Explorer to access ACS.

  Sent by Cisco Support technique iPhone App

• Install certificates for EAP - TLS does ACS does not work

  Hi all

  I have two problems.

  I produced a CSR ACS and sent my people to windows this and they published my ACS with a certificate. Cool.

  I'm going to download the GBA and I put a 'private key file?

  What is this file? and where can I get a? What is this long string of characters that generate the CSR, I sent the boys of windows?

  Also, I managed to just put any old rubbish in there? and I was surprised he accepted.

  Restarted the service IS and I tried to turn it on eap - tls on the "Overall Authentication Configuration" page to get only the message

  Could not initialize authentication PEAP or EAP - TLS because that Protocol

  certificate is not installed. Install CA using "ACS."

  «Configuration of CA page»»

  Now, I'm a little confused, because if have the installer GBA incorrectly, because of my lack of understanding of what this private key file and how it relates to all which?

  Thx a lot indeed.

  Ken

  I'm having the same problem. It seems the guys from windows to generate a cert that it must be exportable, which offers also private key file. I tried the following without success document. It can work for you, however, http://www.cisco.com/en/US/products/sw/secursw/ps5338/products_configuration_example09186a008020a45c.shtml

  I also tried to have the ACS to generate a certificate self-signed, that works. But on the client, you must uncheck the box validate the server certificate because GBA is not a trusted certificate servers. Right now I'm trying to understand how ad to publish the ACS as a trusted cert server so windows knows to do trust the cert of the ACS. Through all this, I found that you can configure in several ways, the most difficult part is to find a way that works for you.

• Why ACS can not display page downloadable ACLs

  Hello

  I have a GBA for windows, version 4.0.1.27.

  After successful installation, I found there is not point of downloadable ACLs in the shared component profile? I can see his support on the right place.

  Why not configure downloadable ACLs in this ACS, y at - it all the other work I have to do?

  THX

  Hello

  Try this.

  Configuration of the interface-> Advanced Options

  Click the check box for

  Download ACL user level

  Group and level downloadable ACLs

  Click on submit

  Then go back to the shared profile components and it should now be an option.

  HTH

  Jon

• Cisco ACS: page not displayed not!

  I installed Cisco ACS v 4.1.While through the different tabs, suddenly, I got the page written common IE "this page cannot be displayed".

  It is all of a sudden in the meantime & there is no expiry/delay period while working on it.

  Server: HP DL380G5

  OS: Win2k3 Enterprise Edition SP1

  Kindly guide me!

  Rajeev,

  Add the DCC address in Internet Explorer trusted sites. Also check if the acs services are up n running, especially csadmin.

  Kind regards

  ~ JG

  Note the useful messages

• Secure ACS Authentication and Authorization with SecurID

  I am able to authenticate connection attempts using an external database (RSA SecurID).  The problem is that everyone with a token is authorized to connect on any switch with priv15 or whatever I put (but no way to control who gets what access).  How can I allow users based on a certain type of belonging to a group?  The SecurID server is already integrated with LDAP, it only checks to see if the user exists in the database.

  I need to create two groups, or even only allow a single group and deny everyone, but anyone in the organization with a token is allowed to connect.  I can't find guides who do anything beyond authentication when you use a SecurID token.

  Thank you.

  Hello

  Have routers and switches, you given the command "authorization exec default group aaa GANYMEDE", it seems that you have only defined authentication on devices. When the control is in place, user access privileges may be governed by the ACS. In network administrator access by default policy (if you are using the default strategy for GANYMEDE), to set the authorization rule to verify membership in a user group and provide the appropriate profile of shell. Make the default rule to give DenyAccess shell profile to other users.