6.5.0 fan control and control of the fan

Similar Questions

• How to control a Mac mini with HDMI ports fries and lightning? (The rest is ok)

  Recently, a lightning strike fried video output (HDMI and lightning) ports on my Mac Mini end of 2012. As far as I know, the rest of the machine works fine. It's just blind. I can't have everyone working on this, but I don't want to throw a perfectly (well, almost perfectly) computer works.

  If I can get a control over the Mac Mini for a few days, I could set up as a dedicated time Machine or maybe even an iTunes or media Server. How can I achieve this?

  Configure the screen sharing on the Mac.

  To do this, you must have another recent Mac.

  You can start the problem Mac in target disk mode, connect the two Mac by FireWire or Thunderbolt, boot the Mac problem with button down T, boot the first Mac since the Mac HD problem and sharing Setup screen

  http://www.macissues.com/2014/05/07/how-to-set-up-and-use-screen-sharing-in-OS-x /.

  http://www.TechRadar.com/us/news/computing/Apple/how-to-use-screen-sharing-in-Ma c-os-x-1296285

  Alternatively, you can take the drive out of the Mac problem and start another Mac that and configure sharing screen.

  You can also get a USB video card and put in place by the target disk mode or by removing the similar disk for screen sharing

• Why is it not possible to use SIRI on my apple TV remote to control the HomeKit products? I should be able to control all the devices with my Apple TV remote and SIRI HomeKit!

  Why is it not possible to use SIRI on my apple TV remote to control the HomeKit products? I should be able to control all the devices of HomeKit with my SIRI voice remote control and using Apple TV!

  If the new apple TV can act as a concentrator HomeKit and I use SIRI on my iPhone to control my locks, thermostat, lights, etc. Why am I not able to do the same thing with SIRI via voice commands on my Apple TV remote? When is this going to work?

  Also, when Apple will come out with a response to the echo of Amazon? I've tired to wait... do it already! If you build it, they will come...

  Thank you!

  This is a community to a user, and Apple will not see your rant. If you have suggestions about Apple TV, Siri and HomeKit the best thing to do is to submit your comments here. http://www.Apple.com/feedback/AppleTV.html

• Keep losing the customization of controls after the new start or updates [firefox 24/25/26] 'customize navigation as bookmarks, back buttons and reload '.

  Since the 24 FF and also in the 25 & 26 it keeps losing the customization of controls after new impetus or updates.

  I always do this: 'Customizing the navigation like back, home, bookmarks, & reload buttons' - http://mzl.la/LqHj2n.

  When I updated from 23-24/25/26 or have a crash FF in one of these versions, the customization is default return. I do not have to repeat this every time!

  What is your operating system?

  You can check the problems caused by a corrupt localstore.rdf file.

  • http://KB.mozillazine.org/Corrupt_localstore.RDF

• How can we separate "Icons and text" of the browser control buttons (back, forward, etc.) since the icons on the toolbar of the add-on?

  With us, it is not a problem. I don't know why it's different here at work - even editing, same settings (as far as I know).
  Windows Vista
  Firefox 7.0.1
  Status 4 Evar installed to activate the add-on bar in a status bar

  I have a NoScript module icon in the corner, which works very well. If I add a GreaseMonkey icon in the menu customize, "Icon and the text" is displayed for this icon as the icon and text browser controls (home, stop, etc.). Other icons the module show icon and the text (S4E, for example). NoScript is the only one I've found so far that collapses down to just an icon.

  I like this leads to the bar having a higher status (add-on). Basically what I want is for only the icon is displayed in the State (toolbar Add on), while keeping icons and text in the browser controls. My current solution is simply to remove the other icons of the add-on - it from the status bar (add-on), but which removes the ease of turning on/off and setting options.

  Please tell me if I can provide you with another thing and thanks for your help.

  Edit: I have some screenshots to show what I mean.
  desired behavior
  problem when the icon is added

  I tried, and while it does not remove the text, buttons retain their width, collapses don't not down icons. I was able to get exactly the effect I want to by changing the setting in the DOM, as stated in my post above, but which only lasted as long as the session and returned to the way it was before, when I restarted Firefox.

  After a few tries, I finally joined the userChrome following tweaks. This tweak sets the buttons didn't use any text, be limited to 20 pixels of width, and, if a drop-down list arrow is present, to hide that. Greasemonkey uses a drop-down list item separated so it must be hidden specifically.

  #addon-bar .toolbarbutton-text { display:none !important; }
  /*The following work for most of my icons except Greasemonkey*/
  #addon-bar .toolbarbutton-menu-dropmarker { display: none !important; }
  #addon-bar .toolbarbutton-1 { min-width:20px !important; }
  /*The following are specific to greasemonkey*/
  #addon-bar .toolbarbutton-menubutton-button { min-width:20px !important; }
  #greasemonkey-tbb > dropmarker {  display: none !important; }
  

• Satellite A300 - control press the button Mute and didn't turn on the light

  I just bought Satellite A300-U01... Well I've seen other A300 their first touch multimedia keys works at the TURN of the lights on the laptop as well. My works for MUTE.

  How can I change?
  I check in Toshiba sat down he gives to option 1 of Mute another for DVD?

  Hello

  He is an Australian series. Am I wrong?
  I put t know if this is possible on the Australian series laptop.

  On Toshiba A300 European notebook, you can change the configuration of the pushbuttons
  If you want to assign another feature so you can set it new Toshiba control button. Check you Toshiba Assist-> Optimize-> Toshiba button support

  In addition, go to Toshiba HWSetup and turn on the light.

  Welcome them

• A way to group controls and indicators on the Front Panel and that they can be made Visible or not as a group?

  I would like to combine several orders and LEDs on the front panel in a group in a way that allows me to do the whole group Visible or not.

  I tried to use a Cluster, but it has a side effect that all elements must be inside the controls or indicators, but not mixed.

  Is there any graphic element, like a panel that can contain other controls and indicators on the inside and make them Visible or not as a group regardless of whether they are commands or the LEDs?

  Good suggestions on how to do this?

  Thank you.

  The tab control is still not my favorite, appearance but it's a way fast and effective to show and hide groups of controls and indicators.

• Keyboard and a chain of control to the screen

  I feel a strange behaviour when I use the keyboard (OSK) and a chain of control on the screen.

  I develop an application that you can use the OSK to enter some data on a touch screen with no physical keyboard. I have a Machine to States Event-Driven set up at the key event to the bottom when a word/characters are entered and the user presses the Enter key on the OSK. I noticed that if I probe the wire wuen Vcle I press the Enter key on the OSK, it appears like a back press. Not much, I thought, just to see if the Enter key is pressed and continue on.

  When I went to test my program, I noticed that my values were as if nothing has been entered. Digging a little further, I noticed that my original data are still there if I press the BACKSPACE and delete the return order. Probe string wire in the control of the chain indicates that the value comes back as an empty string in my control channel even if my entire string is physically still there. I can press the BACKSPACE (remove the carriage return) and see my original text. What, in my view, that happens, is when I press the Enter key on the OSK, it inserts something and moves my text upwards or downwards, and when I use the node property to retrieve the data in the control of the chain, I get an empty string.

  How did you get around this? I would like to hear your solutions.

  Have you tried right-clicking on the control of the chain (assuming that it is "ID mould to enter") and by assigning the value 'limit to the single line "? Sounds like your settings cause hit enter to add a line instead of the finish of your entry change. (You can also change the behavior of 'back' in your settings of LabVIew)

• Additional panel in the panels and controls in the Panel generated .h file

  I have a sign in my project, it is called LO_LVL_PNL.

  The generated header file seems to think that there are more. Here is the 'Panels and controls' section on the generated header file:

  / * Panels and controls: * /.
  #define  DITHER                           1
  
  #define  DITHER_CLOSE                     2       / * callback function: DITHER_CLOSE_CB * /.
  
  #define  DITHER_Dither_Settings           3       / * callback function: DITHER_CONTROL * /.
  #define  LO_LVL_PNL                       2
  
  #define  LO_LVL_PNL_SENDBUTTON_2          2       / * callback function: DIDsBUTTONcb * /.
  
  #define  LO_LVL_PNL_SENDBUTTON_3          3       / * callback function: EraseBUTTONcb * /.
  
  #define  LO_LVL_PNL_SENDBUTTON_4          4       / * callback function: SENDBUTTON_noe_cb * /.
  
  #define  LO_LVL_PNL_SENDBUTTON            5       / * callback function: SENDBUTTONcb * /.
  
  #define  LO_LVL_PNL_RESET_CAN             6       / * callback function: RESET_CAN_CB * /.
  
  #define  LO_LVL_PNL_UUTRESPONSE           7       / * callback function: UUT_RESPONSE * /.
  
  #define  LO_LVL_PNL_CLEARBUTTON           8       / * callback function: CLEARBUTTONcb * /.
  
  #define  LO_LVL_PNL_EXIT_BUTTON           9       / * callback function: cb_quit * /.
  
  #define  LO_LVL_PNL_Comm_Set_TEXTBOX      10
  
  #define  LO_LVL_PNL_COMMANDBUTTON         11      / * callback: CheckState * /.
  
  #define  LO_LVL_PNL_COMMANDBUTTON_2       12      / * callback function: Select_Files_DID * /.
  
  #define  LO_LVL_PNL_BINARYSWITCH          13      / * callback function: SetProgram * /.
  

  in my IUR I can find LO_LVL_PNL components, but not parts of DITHERING.

  Then, I renamed my generated header file, so it can regenerate without these additional items, but they get included when I recreate it.

  In the file of the UIR, if I double click on he Panel it opens and displays that the Panel is called LO_LVL_PNL.

  It started because I'm trying to read the value of a switch on the Panel, and in the call, I get a runtime error that follows:

  GetCtrlAttribute (LO_LVL_PNL, LO_LVL_PNL_BINARYSWITCH, ATTR_ON_VALUE, & on_off);

  NO MORTALS RUN - TIME ERROR: 'gui_handler.c', line 135, col 13, thread id 0x0000179C: library function error (return value ==-42 [0xffffffd6]). The handle is not a panel handle

  I don't know if it's two separate issues, or DITHER things cause the error; but I need help to fix both.

  The first parameter to GetCtrlAttribute() must be the handle Panel, not the ID of the Panel. The handle is returned by your LoadPanel() call.

  Do you already have a group called DITHERING? Copied from an earlier project, perhaps? Perhaps the editor of UIR has hidden or placed outside the screen. Try using the option editor find to see.

  JR

• Deleting the definition of Type casuses control a lot of misreferences and program in the block diagram errors

  In LabVIEW 2010, I have a Def Type control i.e. a Cluster with several other controls within the Cluster. Apparently, the references to the controls in the block diagram are based on the order that the controls have been added to the Type definition command. The side effect of this is that if a control is removed from the command of Type definition, many of the done Variable reference in the block diagram or now either broken, or worse still, refer to wrong control in the Type definition. These problems are quite difficult to find and fix.

  Comment: If you create a control of Type definition and make a Cluster. Now add any controls to the Cluster in an order, let's say A, B, C, D. Their types does not matter. Now use the Type definition in one or more controls on the front panel. In the block mark references to controls inside the Type Def would control on FP. Now return to the Type definition and remove the command B of the definition of Type. Now, lots of errors appear. Broken links. But worse still, you see old references to B that now refer to C and old references to C are now referring to the old references to D and D are removed altogether, etc..  This side effect is much more errors, broken links and misreferences than expected otherwise.

  How add and remove controls anywhere in a Cluster in a Type definition, at will, without creating a whole bunch of errors in program, broken links and misreferences for controls in the Type definition that have not changed?

  
  

• Control valve tank with plots and twists of the water

  Hello everyone!

  This is my frist real project. And I am in love with this program so far!
  I have a little problem. Here it goes:

  The project of the University which has been given to us is to simulate a (entrance OPEN/CLOSED valve) water tank filling and emptying (output range of 0 to 100% valve), but with a few twists. It is done by the command to the movement by the following formula: flow rate [%] = position of the valve [%] * current water height [%]. (The output valve takes values in percentage from 0 to 100% giving the voltage digital output of 0 volt to closed(0%) or 5 volumes for open(100%), the strange part, is that the digital output can have a value of 0 or 1, so the position of the valve is "simulated".) And the supply valve (valve entrance) water can be open or closed (if 0 or 5 volts)

  -Sequences cannot be used (only one for initialization and cleanup can be used)

  -When the water level reaches 10% of the max height, LED lights, the output valve closes and the input valve opens. The LED is on until the button is pressed. The output valve cannot be opened until the water height is greater than 50%.

  -When the water level reaches 90% of the max height, LED lights, the entrance valve opens. The LED is on until the button is pressed. The output valve cannot be opened until water height is less than 50%.

  -There are two mode selectios:

  Control by hand: the person sets the position of the valve in percent and the flow is calculated by the formula and displays on the screen.

  Automated: Every 2 seconds the program assigns the place valve so that the current is constant, it is the value by the person.

  -(N'ont pas gottern ici encore) ESD (Emergency shutdown switch) the when is pressed both the entry and exit valves are closed. The entrance valve cannot be oppened up to the RESET_IN key. If the program is 'Control in manual mode' output valve cannot be opened until the RESET_OUT touches. In which case the output valve is in "Auto" mode, it does not start work until the RESET_OUT touches.

  My main problem here is the fact, I cannot use sequences and nested, then the loops do not work. The aqusition of data stops until the inner circle loop ends and I need both work. Especially for the 50% rule.

  I've been hitting my head for a few days and still couldn't come up with a solution.

  I have attached the VI.

  Tips are welcome!

  For the time being the outputs inputs/digital analogue are a simulation (when the time comes the USB-6008 material is used).

  There is some things that confuse me (as if the valves are percentage, from 0 to 100%, or digital, 0 or 1), but regardless, it's a detail.

  Review the task and consider what you want to do and that the "States" the system may be in.  [This with a pencil and paper, do not open LabVIEW yet...].  The description of your problem learn you something about the transition from one State to another.  Here is a thought exercise:

  Suppose you are in a "State".  Let the system to "do its thing" for a second, which could involve the water flow.  At the end of the second re - evaluate your state - it changed?  Continue to do this...

  This model of 'something' is called a State Machine and LabVIEW has some very good examples and tutorials on the creation and use.  The important things to do before you make your coding is (with the pencil and paper) decide on your statements, decide on the transition rules, and then you are ready to code.

  There are different ways to build a State Machine in LabVIEW, but the basic idea is quite awhile (to keep things moving along, a shift register which includes the current state, usually represented as an enumerated, Type whose values are simply the names of your States (made for a very mnemonic routine) and a Case statement whose power is the State of the shift register that contains the code to achieve this) particular State of loop, including the implementation of transitional rules (which can cause a new State on the registry to lag when it comes out of the investigation of the case).

  A great exercise.  Strive to keep your block diagram on a single computer screen by making use of the screw subgroup chore (as the management of changes in the water level based on the current water level and "States" (which here means 'values') two valves).  Once you understand the 'Idea' State Machine, you should be able to write the code for this problem quite easily.

  Bob Schor

• Programmatically set the size of a table control (not the number of col and lines)

  Hi all

  I am trying to create a little VI, in which the user selects the number of columns and rows in a table, and after clicking on a button 'OK', the table control is displayed in the control panel (to be filled in by the user). To do this, I use the nodes property to the number of columns and lines. I have no problem with that.

  However, I want to "limit" the size of the control table (control of himself, not the dimensions of the table) and make use of vertical and horizontal table, the scroll bars. I want to avoid it is that passes type 100 user and 100 lines and appears a huge table control.

  I could tho this by using an array instead of an array, via the node property "size", but I would use an insead table a table.

  Thank you very much

  Daniel

  With a table control, you cannot set the display size to be anything other than a multiple of a complete cell.

  If you are limited to a number of lines and columns.  If you want to resize with more control you also need to resize the control within the Bay, accessible via the property 'picture Element '.

  Another option (but seems huge exaggerated) is to place your table in a secondary and set the size of the secondary to the size you need and enable scrollbars for her.  It is not an option that I would choose but if it helps...

  Have it, your description of your user interface sounds not very intuitive.  How the user knows at any time exactly what cell they access if they have to scroll backwards?

• Weird problem with control of the ring and foot

  So I have some sort of weird issue with a control of the ring and a chart. I'm with LabWindows/CVI on a Windows 7 computer. The part of the program I'm looking at is basically to navigate through data - there are several "transition" (rehearsals experience), and you can choose the one that you want to watch in the list.

  Normally, you would select transitional in the list, it plots the data, then it is done, basically. However, all of a sudden (don't know how long it spent for), when I select anything except 'Average', he made all the tracing and such, then it changes control of the ring to 'Average' (it is not plot the average data or generate all the reminders that I can tell).

  Now the thing the more bizarre as you can see below, it seems that the switch happens just when I draw something on the chart:

  

   

  So, it's just weird. The code in this section is here:

     if(uidc.polyon) {
              polynomial_subtraction(curr_data, np, uidc.polyord, 0); // 0 Skip for now
          }
  
          // Scale the curr_data for gains, then pre-scale the FFT data
          // to have no change in the power spectrum (multiply by (2/np)
          for(j = 0; j < np; j++) {
              fft_data[j] = curr_data[j]*2/np;
              curr_data[j] = curr_data[j]*uidc.fgain[i] + uidc.foff[i];
          }
  
          uidc.fplotids[i] = PlotY(dc.fid, dc.fgraph, curr_data, np, VAL_DOUBLE, VAL_THIN_LINE, VAL_NO_POINT, VAL_SOLID, 1, uidc.fchans[i]?uidc.fcol[i]:VAL_TRANSPARENT);
  
          // Prepare the data.
          FFTEx(fft_data, np, npfft, NULL, FALSE, curr_fft);  // Do the fourier transform
  

  DC is a structure that I use to better organize some UI controls and uidc is for display RAM variables, then dc.fid is the Panel that is embedded in the tab "FID", dc.fgraph = FID_Graph and corresponds to the chart control. Control of the ring is actually in a child Panel, dc.cloc [0]. FID_Graph has a point, it can produce, but the reminder is empty (no not coded something there yet).

  I have also considered that perhaps something in another thread (I don't think there is, but whatever) I see is the cause, however, this behavior still happens on that line. I tried to break in different locations, on hold, then continues, as well by adding a loop containing Delay (0.01), a loop of 100 times. Always happens after the conspiracy.

  Does anyone have any idea why this might be happening?

  Hi Paul,.

  I don't have a solution, but I wanted to point out that, even if you see the ring to change its value only when you call the function of tracing, that doesn't say what this function call that really changes the value of the ring. In CVI, some drawing operations are batched, for performance reasons, and the Panel updates only visually at certain times. One of those moments when you draw a chart data. Yes, the ring changes visually at this time there, but it is probably just 'catch up' a change earlier.

  As you are looking through the code, when the value of the ring, you can use the term > command update UI to force the update panel, so that you don't have to wait for the tracing function and see if all goes well this change happening earlier.

  Luis

• Cluster (buttons and the radio channel controls) - select the right file

  I have a list of text files and I need to select and open an of based on radio button selection.  How to sync the radio button with control of the chain so that I can get the name of the control of the chain and open the right file name?

  The attached vi does not work as I would like.

  Edit: Or is there a better way?

  Depends on the source of the list of files.  If you embed it in LabVIEW via a table or another method, then obviously a recompilation must be made.

  If the list of files will come from a specific directory, then simply read the list of the files from there when starting of the VI (see example).

  Or you could store the list in the text file and read the file at the start of the VI.  You can edit the text at any time without recompilation.

• Why my front panel opens with a white background and most of the invisible control

  When I open my vi and several others, they open with a white background and most of the controls not returned as theis

  

  After I resize it looks like it should

  

  It's probably somewhat similar to these problems of crazy object.

  Sometimes copy/paste works because it takes your code on a VI that could have a corruption and put in a cool VI.  In your case, the corruption could be linked to the control itself and he just copied over in the new VI.  Money controls are a relatively recent creation which added some fancy appearances.  They don't seem to be the style that is most likely to have some behind the bugs of scenes from the styles of controls that were longer.

  If you have a shared services provider, or if a person nor jump here and wants to study, they want to can see your VI and understand what goes wrong.  If this isn't the case, I hope that what you've done has solved the problem and you can spend without return.

• Using a control of the chain with the Enter key, return * and * allowing repeated identical entry

  Hi all

  There must be a simple solution for this, but it's Friday afternoon, and my brain is not cooperating.

  I create a simple terminal through which a user can interact with an instrument. My question is about the only query string control. The button send and the Terminal Table are here for reference.

  

  Here is my desired behavior:

  (a) the user types a command in the field of the query, tape input or return. An event is triggered, and the request is sent to the instrument. The focus remains on the field in the query.

  (b) with any other action the interface user, the user types Enter or return again and again, by triggering an event that sends the request to the instrument every time Enter or return is typed. The focus remains on the field in the query.

  Here's what I have:

  

  This allows for one), but fails to b). The reason is, because the value of the field in the query has not changed, change value event does not fire when the user starts to spam keys enter or return. There is a way around this, as suggested by this post. Here is the solution in a few words:

  

  Instead of looking for the change in the value of the query command, the event fires for each key event to the bottom of the control and resembles a pressure of enter key or return. What attracts the user action, even if the content of the field of the request have not changed. The problem with this approach is that, when this event fires, I need to read the value of the query string order and send it to the instrument, but the value I get via the local Variable query is the old value, probably because the key down event fires before the value of query is saved as changed. Is there a way to programatically "enter" the contents of the control channel so it is recorded as a change in value, until I have the question via a local Variable? Is there a different way I should go about it? I'd rather not do anything that bound the input keys or return to this particular area, since I have many other UI elements that need these keys in my program.

  If not, is there a way to make the control of the fire 'Change of value' query string event when the user presses enter or return even if the value has not changed?

  Thank you for your comments!

  I thought about it.

  (1) control of the string (query) a value of update while typing.

  (2) save the key event down to the control of the chain. If the entry or return was pressed, send the state machine to the State 'send request '.

  

  (3) in the application 'send' State read control channel via the local Variable value.

  

  This is the desired behavior to allow the user repeatedly hit entry or return to regularly send a command, and the user can also type in a new order and send it by pressing enter or return.

  Thanks to all who have helped me this something to think about!