Acer Iconia A1 - tablet will only power on the acer logo and no more.

Similar Questions

• Grammar red line will only appear on the words misspelled on the half top of my document, but not on the bottom half how to fix this?

  Grammar red line will only appear on the words misspelled on the half top of my document, but not on the bottom half how to fix this? I am writing an essay and I know I misspelled words it contains, but the red line will not work. What should I do about it?

  Hi Brittany,

  You use Microsoft Word?

  If you use Microsoft Word, you can post your request in the Forum Office for assistance.

  Microsoft Office Forum

• My iPod 5th generation does not start (it will stay on the apple logo) and will not be detected by iTunes.

  Last night I tried to turn on my iPod that has not been loaded. I plugged it so that it can start loading. I think the iPod as was the accused, has no need for me to start and should have done by itself. When I pressed the button home to start using it, I noticed it was not on. Then I pressed the power button and then saw he was showing the Apple logo and then it turns off again. I tried pressing the "home" button and the Start button / stop at the same time and the same thing will happen. I also tried connecting to my computer and it did not recognize.

  Try the remaining actines of the:

  - iOS: do not respond or does not light

  -Also try DFU mode recovery mode post-test

  How to put iPod touch / iPhone in DFU "Karthik doodles."

  -If failed and that you cannot completely turn completely the iOS device, leave the battery to drain completely. After loading a hour repeat the foregoing.

  -Try a different cable

  -Try on another computer

  S ' there is still not successful that usually indicates a hardware problem and an appointment at an Apple store Genius Bar is in order.

  Shop Apple Store - Genius Bar

• My pavillion g6 will get not passed the windows logo.

  When I start the laptop, it loads up the windows logo, and then freezes. only one or twice because he did this was he actually got past the connection but still slow rest, as if it were frozen. Once on the windows logo I can't do anything with the laptop. the only things I can do is turn off by holding down the power button or out of the charger and let it die. If someone knows something please help.

  Hello

  303 error code is a disk failure short self-test and would indicate that hard is defective and must be replaced.  This is also consistent with the question of commissioning.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, please let me know - includes the complete model number and Nr of your notebook series g6 (from under your laptop service tag) - see here for an explanation.

  Kind regards

  DP - K

• Hello. I have the DVD of Lightroom 5.7.1 version. He just started is behaving badly and I've deleted and reinstalled the product. When I'm in the 'development' module, I get random stains of color in my images. This only happens in the develop module and

  Hello. I have the DVD of Lightroom 5.7.1 version. He just started is behaving badly and I've deleted and reinstalled the product. When I'm in the 'development' module, I get random stains of color in my images. This only occurs in the develop module and no where else. It also does not reach any other software or area on my pc. I also changed the cable and the same triesd another monitor. Anyone have any ideas? Thank you.

  Are patches of red and blue color?

  If so, you probably have warnings of cutting of light/shadow enabled. Press J to hide them.

  You can also activate their power by clicking on the arrows up left and right of the histogram.

  Salient facts cut medium red, medium blue clipped shadows.

• My iphone 6 does not light, I held the home button and power at the same time and no vibration or no sign of life, any suggestions as to what it could be would be appreciated

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Marley6921 wrote:

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Put it on wait ten minutes if the phone did not come one, then hold down the sleep/Home button until you see the apple logo and then release, make sure that the phone is still connected to the charger.

• IPhoto on the external hard drive will not launch despite the force quit and relaunch several times. Can someone help me?

  I have a MacBook from 2008. 4 years ago I moved my iPhoto on an external hard drive. I have thousands if photos on it. IPhoto on the external hard drive will not launch despite the force quit and relaunch several times. Can someone help me?

  < re-titled by host >

  I moved my iPhoto on an external hard drive.

  Did you move the iPhoto library for the external hard drive or the iPhoto application, or both?

  How is formatted the external hard drive? Is the file system on the drive Mac OS extended (journaled) or other system files?  Is the drive directly connected by USB or similar, or is it a SIN?

  IPhoto on the external hard drive will not launch despite the force quit and relaunch several times.

  I don't understand - if you force quit smoking, launches the application, or you can not force it quit?

  IPhoto is suspended without doing anything, when you launch?

  What version of iPhoto does? And what version of Mac OS X?

• How to unlock the c: drive. I have only access to the folder users and subfolders.

  I have only access to the folder users and subfolders.  Everything I tried was "access denied."  I can't get to the root of c:.

  Hi, Scrivmark

  The default C: drive system is not intended to access directly by users and therefore users have restricted access to its root in the premeditated or premeditated damage prevention vital system files. If you are an administrator you can allow full access to your account to all or specific files on drive c (including a root folder) by editing its ' authorization of the lists by right-clicking on a file and choosing "Security."
  If you are not an administrator, you should ask another user whose account is Administrator (or equivalent) privileges to access the interesting files to your account.
  In both cases, you must understand damage system files, you can do.

  This suggestion is the intention that your computer is virus-free.

• Iconia W4-820 will not charge with the power adapter USB Std

  Bought my W4 Iconia four weeks ago, a demonstration model, the last of them. It was packed in the box with a micro USB x adapter USB OTG cable and a power adapter. Back at home I discovered that the power adapter has been to Asus, possibly mixed in the shop. The prospective buyer of the Asus Tablet demo likely will get the Acer adapter. Adapter Asus with micro USB male connector works fine; specs are 5.2V - 1.35 amps; seems to be a STD USB adapter. The Asus adapter has a connector to USB female port to connect to a USB x microphone cable to USB adapter (with cable power adapter came in the box). Bought a 2nd power with USB 2 socket adapter to connect my W4 Iconia and my Garmin Zumo390 browser to an adapter. Specs are 5V - 3.5 amps.
  The Zumo works very well with the new card, but does not work my W4. Charge light stays off. USB ports switched to he Zumo and the Iconia W4, but same result. Zumo fresh, but W4 not. Borrowed another power adapter USB, 5V - 2 mines anti-personnel and new Zumo accusations, but the W4 still does not work. Also tried different USB adapter cables, but the same thing; Zumo invoice, W4 does not work.
  How is that possible? I can't tell the difference of 0.2 V between the Asus adapter and a USB adaptor STD would make the difference. But maybe I'm wrong. Wanted for adapters for the W4 Iconia and found several, but all the 5V as expected.
  Can anyone help.
  Will go to the shop again next week, but if I need an adapter V 5.2 I should order with Acer. 5.2 V adapters do exist not (readibly).

  Resolved issues. A dark and humid Sunday afternoon back to the store with the Tablet and all the bells and whistles. Changed the card Asus for the original Acer 5V - 2Amps (10W). Took the time to find the Acer adapter in the store. Demonstrated the adapter 2nd with 2 output USB ports and it wouldn't work with the Tablet W4. Tried another and found to be ok. 2 USB ports have a different power, a port for a smartphone and the other port is one tablet. Total power rating of the adapter is 17.5W (5V - 3.5Amps); some 2.5 and 1Amps. A happy man is back home again.

• My Windows XP laptop does not connect to my 2WIRE router wireless, but do my other laptops. It will only connect with the ethernet cable. What is the problem?

  What I'm doing.

  1. my laptop is a Toshiba XP

  What serial number and model of Toshiba?

  What type of encryption 2wire router uses for now? Type of WEP or WPA? If the latter do you know if your XP laptop wireless card supports WPA (some older cards only). If you find that this is the problem, you can go to the WEP encryption or buy a WPA compatible device to use instead of the current device on the XP laptop.

  If you don't know how to find this information...

  The range and the model are probably on a sticker on the bottom of the laptop.

  I think that there is a sticker on the side of 2wire routers (leastways are those provided by BT) gives you the encryption key and this might also state what is the type of encryption. Or, if not, open a web browser such as internet explore/firefox etc and go to http://gateway.2wire.net, somewhere on the router admin pages, you will find information on wireless security/encryption.

  Regarding the card laptop wireless, I can help with this if you give me the range and the model as requested above. I can, also, be able to determine from the description of the device in Device Manager. Click Start, click Run, type devmgmt.msc and press ENTER. Network adapters (click on +) and transcribe the wireless adapter that there are listed in a response to this post.

  Tricky

• A recently sent the pictures on a disc of ambient light. now lightroom will only bring up the photos sent to a player, instead of all my photos previously in lightroom with their keywords. How to restore pictures of those missing with their keywords ba

  My lightroom will only bring up pictures I've added a reader, can't see all my photos in lightroom. How can I get all my pictures back in lightroom? It seems that lightroom is only looking at the pictures in a single drive. When I open lightroom an error box comes up saying "error unexpected opening catalog. '" The catalog cannot be opened due to an unexpected error"when I try to"choose a different catalog", the selection will not fill to the selected file, so I can't further. How to get out of this cycle? That's happened?

  reset your preferences - https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html

• Tecra M4 Tablet is underspecced compared to the United States and France

  I want to buy a Tecra M4 tablet. The main reasons are: optical drive, with a resolution SXGA + and a good graphics chip.

  Toshiba saw fit to make us pay more than the United States and France for a laptop with only 1.73 Ghz, 60 GB hard drive, Combo DVD/CD-RW a skinny nVidia 6200 with 64 MB of ram.

  In the United States they may have 2.13 Ghz, tickets (+ R double layer), hard drive 80 GB and nVidia 6600 GPU with 128 MB of ram. All for less than what we are paying for our pathetic version.

  Because they do not give us a DVD burner, those who need to make restore disks will have 6-7 CD - R. Who can be bothered and dealing with that many discs.

  Toshiba you have really disappointed me. Re-enter your.

  I agree but I still love my M4.

• the power of the spectrum graph and butterworth filter

  Hello

  I am beginner in labview, I want to see the power spectrum of the sound samples, I want to see if there is any reason in these samples.

  I use spectral measure, and then I filtered with butterworth filter samples. For output I using waveform graphs.

  Before filtering the signal, I'm in the x axis of the graph between 0-22500 and the data mostly in 0-2500.

  I've tried to filter using these values (fs = 1000 Hz, 0.125 hz = fl and fh = 500 hz) and the graphics almost the same thing but the axis of the graph is between 0-0, 5.

  issues related to the:

  What is the x axis properties? Why is different, but the graphics are the same?

  Make the mistake with the program?

  Hi Limavolt,

  You have a problem with the bandpass filter VI, this VI generates only the signal of value i.e. table DBL. The signal is a cluster.

  solution 1: you need to calculate 'dt' using the sampling frequency and use VI waveform construction to generate a signal's own scaling. 

  Normally, dt = sampling frequency/No. samples

  Solution 2: replace the VI butterworth filter with filter VI express, this will produce signal without scaling.

  

• How can I set up my new tablet to take a snapshot using the windows logo and the low volume of screen button?

  Acer Iconia W700 tablet with Windows 8.

  Try to follow the first option on this page, but nothing is happening: http://windows.microsoft.com/en-us/windows-8/take-a-screen-shot

  Acer Iconia W700 tablet with Windows 8.

  Try to follow the first option on this page, but nothing is happening: http://windows.microsoft.com/en-us/windows-8/take-a-screen-shot

  Hello

  Read the Notes at the bottom of this page.

  "Some laptops and other devices do not have a PrtScn key or may use a different key combination to take screen captures." Consult the manual that came with your laptop or your device for more information. ''

  Go to this site and select your model for specific help.

  ASUSTeK Computer Inc. - Support - Troubleshooting:

  http://support.ASUS.com/download/options.aspx?SLanguage=en&type=9

  You can also discuss this issue with other users that have this template.

  ASUSTeK Computer Inc. - Support Forums:

  http://VIP.ASUS.com/forum/default.aspx?SLanguage=en-us

  Concerning

• Error 17-Windows will not load past the splash screen, and system repair has no effect...

  Hi all, my problem is the following. Off my laptop the night before, an upgrade has been installed as usual. However, when I tried to start my computer the next day, I was meeting with a choice of operating systems, one was vista and one was something called "openSUSE 11.2 installer (NET).» Of course I wanted to choose vista, but when selected has been sent to a screen that read (sorry for the amount of the entry).

  Start "openSUSE 11.2 installer (NET)".

  (hd, 1)

  Specifien type is ntfs, partition type 0 x 7

  /openSUSe/ kernel linux devfs = mount, dall ramdisk_size = 65536 = ftp install: //ftp4.g wdg.de/pub/opensuse/distribution/SL-OSS-factory/inst-source/ server = ftp4.gwdg.de lang = en splash silent vga = 0x31A

  Error 17: File not found

  I don't know much about this sort of thing, so he thought better to include everything I could. At first, I tried to reload Vista, but it just opened the same screen, so found the vista disc that came with the laptop and it is stuck in. I ran sytem repair and system restore and both have had no effect.

  I'd appreciate any help is sorting this point, but if I have to reinstall vista (what I hear the hard disk wipes), is it possible to backup all my files to be reintergrated later.

  Thanks for any help!

  "Off my laptop the night before, an upgrade has been installed as usual."

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost, please include Error Codes, including what you have already posted, andexactly what happens after you tried to update.

  In this way, you will receive the best help.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner