Basic configuration problem - please help!
Hello
I'll put up my first PIX firewall in a network of trial right now, and it is supposed to go into production in the next few days.
I am trying to open some ports for a server inside, doing everything 'by the book' (cisco e-learning, to be exact), but I had no success with that. Basically, I'm trying to map an inside Server (192.168.254.199) to (xxx.115.215.1) external IP address that is assigned to the external interface. The type of traffic that must be passed inside the server is http and remote desktop. (Other users are PATed to xxx.115.215.2) So I tried to use the static/conduit pairs, according to e-learning stuff...
public static xxx.115.215.1 (Interior, exterior) 192.168.254.199
conduct permitted tcp xxx.115.215.1 eq www host everything
driving permit host xxx.115.215.1 eq tcp 3389 everything
After I type this, I can't access the internet from the server, or ping to the outside... and of course can not access office remote/web server from outside, which is the main goal.
Here is the config:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the password xxx
passwd xxx
hostname pix
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside xxx.115.215.1 255.255.255.0
IP address inside 192.168.254.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 xxx.115.215.2 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
allow icmp a conduit
Route outside 0.0.0.0 0.0.0.0 xxx.115.215.125 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.254.100 - 192.168.254.150 inside
dhcpd dns 192.168.254.199 199.185.225.10
dhcpd wins 192.168.254.199
dhcpd lease 28800
dhcpd ping_timeout 750
dhcpd field test.local
dhcpd allow inside
Terminal width 80
Cryptochecksum:xxx
: end
PIX #.
I am sure that the problem is something simple, as I'm just a newbie...
Your help will be GREATLY apprechiated!
Thanks in advance
good news... I'm glad it works now!
Please solve the case, while it appears on the list as "checked"... See you soon,.
Tags: Cisco Security
Similar Questions
-
my Iphone 5 was automatically turned off, and then I couldn't go? What is the problem please help me?
Have you tried to connect your iPhone to iTunes or the wall charger and let your iPhone for 5-10 minutes to charge its battery?
-
VIP - ANALYZE Configuration Issues - Please help!
Hello world
First of all I ask you guys to Please HELP SOLVE ME THIS PROBLEM – thank you!
I am installing grid Infrastructure Oracle 11 g 2 11.0.2.0.3 on Oracle Solaris 11.11 x 86 64 bit installed using Live Media on Oracle VirtualBox 4.2.6.
After you have configured the nodes in the cluster, I ran the cluster verification utility that came out with 100% success.
However, during root.sh run, I get the following error:
/U01/app/11.2.0/grid/root.sh
--------------------------------------------------
CRS-4266: Vote or managed to replace the files
# File group universal name Id disk STATE file
-- ----- ----------------- --------- ---------
1. online 4a3543261bc34fc9bf6e41b5d7fa04c8 (/ dev/rdsk/c8t2d0s1) [OCR]
Located at 1 vote (s) disk.
CRS-2672: attempt to start 'ora.asm' on 'sol1.
CRS-2676: beginning of "ora.asm", the successful "sol1"
CRS-2672: attempt to start ' ora. OCR.dg' on 'sol1.
CRS-2676: beginning with ' ora. OCR.dg' on 'sol1' successful
/U01/app/11.2.0/grid/bin/srvctl start applications sol1 - n... failed
FirstNode configuration failed on line /u01/app/11.2.0/grid/crs/install/crsconfig_lib.pm 9196.
/U01/app/11.2.0/grid/Perl/bin/perl-I/U01/app/11.2.0/grid/Perl/lib-I/U01/app/11.2.0/grid/CRS/install /u01/app/11.2.0/grid/crs/install/rootcrs.pl execution failed
I have re-run this command to see the real errors
/U01/app/11.2.0/grid/bin/srvctl start applications sol1 - n
------------------------------------------------------------------------------------
RPRC-1013: failed to start of ora.net1.network resources
RPRC-1064: failed to start of ora.net1.network on node sol1 resources
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
RPRC-1079: failed to start of ora.sol1.vip resources
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
CRS-2632: there is no more servers to try to place the "ora.sol1.vip" resource on which will achieve its investment policy
RPRC-1013: failed to start of ora.ons resources
RPRC-1064: failed to start of ora.ons on node sol1 resources
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
I ran the following commands to know the State of SAN and SCAN-headphones
srvctl status scan
--------------------------------
VIP scan1 SCAN is enabled
Scan1 VIP SCAN does not work
VIP SCAN scan2 is enabled
Scan2 VIP SCAN does not work
SCAN VIP Scan3 is enabled
Scan3 VIP SCAN does not work
srvctl status scan_listener
--------------------------------------------
LISTENER_SCAN1 listener to SCAN is enabled
SCAN of the earpiece that listener_scan1 is not running
LISTENER_SCAN2 listener to SCAN is enabled
SCAN of the earpiece that listener_scan2 is not running
LISTENER_SCAN3 listener to SCAN is enabled
SCAN of the earpiece that listener_scan3 is not running
srvctl config scan_listener
---------------------------------------------
LISTENER_SCAN1 listener SCAN exists. Port: TCP:1521
LISTENER_SCAN2 listener SCAN exists. Port: TCP:1521
LISTENER_SCAN3 listener SCAN exists. Port: TCP:1521
Here is the content of my/etc/hosts and /etc/resolv.conf files
cat/etc/hosts
-----------------------------
# Public
192.168.56.101 sol1.localdomain loghost sol1
192.168.56.102 sol2.localdomain sol2
192.168.56.160 solfiler solfiler.localdomain
# VIP
192.168.56.111 sol1-vip sol1 - vip.localdomain
192.168.56.112 sol2-vip sol2 - vip.localdomain
# Private interconnection
192.168.0.101 sol1-priv sol1 - priv.localdomain
192.168.0.102 sol2-priv sol2 - priv.localdomain
# Scan
#192.168.56.201 ground-sweeping ground - scan.localdomain
#192.168.56.202 ground-sweeping ground - scan.localdomain
#192.168.56.203 ground-sweeping ground - scan.localdomain
cat /etc/resolv.conf
------------------------------------
#
# AUTOMATICALLY generatedFROM_SMF_V1_
#
# ATTENTION: THIS FILE GENERATED FROM SMF DATA.
# DO NOT EDIT THIS FILE. CHANGES WILL BE LOST.
# See /etc/resolv.conf (4) for more details.
Search localdomain
nameserver 192.168.56.101
nameserver 192.168.56.102
nameserver 192.168.1.1
Here are the details of the network
dladm show-phys
----------------------------------
MEDIA SPEED DUPLEX LINK
Net1 Ethernet up to 1000 complete e1000g1
NET2 Ethernet up to 1000 full e1000g2
Net0 Ethernet up to 1000 complete e1000g0
ipadm show-addr
---------------------------------
ADDROBJ TYPE STATE ADDR
127.0.0.1/8 ok static lo0/v4
Net0/v4 dhcp ok 10.0.2.15/24
Net1/addr static 192.168.56.101/24 ok
NET2/addr static 192.168.0.101/24 ok
OK static lo0/v6: 1/128
Net0/v6 addrconf ok fe80::a00:27ff:fe5f:f484 / 10
I did the nslookup on my name SCAN
Nslookup ground-scan
----------------------------------
Name: sol - scan.localdomain
Address: 192.168.56.202
Name: sol - scan.localdomain
Address: 192.168.56.203
Name: sol - scan.localdomain
Address: 192.168.56.201
I ran the following commands to see if the installation process correctly reads my SCANNING configuration
srvctl stop scan_listener
srvctl stop scan
srvctl config scan
-----------------------------
SCAN name: ground-scan, network: 1/192.168.56.0/255.255.255.0/net1
SCAN VIP name: scan1, IP: /sol-scan/192.168.56.203
SCAN VIP name: scan2, IP: /sol-scan/192.168.56.201
SCAN VIP name: scan3, IP: /sol-scan/192.168.56.202
So it's good reading ANALYSIS information there is so no problem
I tried to start listeners to SWEEP and ended up with the same mistakes
srvctl start scan_listener
------------------------------------------
RPRC-1079: could not start the ora of the resource. LISTENER_SCAN1. LSNR
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
CRS-2632: there is no more servers to try to put the resources ' ora. LISTENER_SCAN1. LSNR' on which would meet its investment policy
RPRC-1079: could not start the ora of the resource. LISTENER_SCAN2. LSNR
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
CRS-2632: there is no more servers to try to put the resources ' ora. LISTENER_SCAN2. LSNR' on which would meet its investment policy
RPRC-1079: could not start the ora of the resource. LISTENER_SCAN3. LSNR
CRS-2674: beginning of "ora.net1.network", the "sol1' failed
CRS-2632: there is no more servers to try to put the resources ' ora. LISTENER_SCAN3. LSNR' on which would meet its investment policy
If it helps, I use automatic network default Solaris 11.11 management but I changed IP addresses of net1 and net2 manually to meet my network
Requirements for the clusterware.
I followed all the steps of the system requirements for installing under solaris 11.
After checking everything I could have as detailed above, I'm now helpless as to where things go wrong
What is automatic 11.11 Solaris network management that does not allow the creation of addresses IP SCAN VIP?
Once again I ASK YOU GUYS to Please HELP me THIS PROBLEM FIX.
Concerning
Terry.Hello
the problem is the host name of the server is resolved is on the 10.X.X.X network.
For example, the cluster requires the public network to be on this network. And the error you get, because this network is on DHCP.If you have the following options that you can try:
a.) change the server to have the host name to resolve to the 192.X network
(b) change the order of the network adapters
(c.) remove the network 10.X.X.X at the moment of installationConcerning
Sebastian -
Resolution / gambling problem please help me
OK, I have vista 32 bit and when I get in any game at all and play... then get out of the wreck is fine... but then when I restart the Res changes again in the wreck the last game I played was set to and if the game does not have my native resolution it mess everything up on top of my desk and its starts to become annoying if someone could please help me because I really don't want to personalize then go to display settings and change every time that I log on... I tried to uninstall the latest software, tried to use the yahoo answers and they are not any help, MY RIG: AMD Athlon x 2 Dual Core 6000 + 3.1 Ghz, 8600 GT, 4 GB of ram, vista 32-bit , 22 inch monitor, native res: 1680 x 1050, Cyborg keyboard game... and I have IE8, any other information you need to know please ask me. Thanx
Maniac of Vista,
If you think that the problem started when you installed the Extreme 3D Pro stick, have you tried to uninstall it to see if the problem goes away? Who will tell you for sure if that's the problem, you can access the web site of the manufacturer and see if they have a fix for this problem, or simply reinstall the software for the joystick could fix.You can also try to do a restore back before the problem occurred:
To restore the operating system to an earlier point in time, follow these steps:
Click Start, type system restore in the search box, and then click System Restore in the list programs.
If you are prompted for an administrator password or a confirmation, type your password or click on continue.
In the System Restore dialog box, click on choose a different restore point and then click Next.
In the list of restore points, click a restore point created before you started having the problem, and then click Next.
Click Finish.
The computer restarts and system files and settings are back to the State they were in when the restore point was created.Let us know if this helped, or if you need further assistance.
Thank you
Gloria
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
I had a "Blue screen" problem, please help me!
Well, I don't really know the source but it happened several times already, here are the details of the error:
Signature of the problem
Problem event name: BlueScreen
OS version: 6.0.6001.2.1.0.768.2
Locale ID: 2057Files helping to describe the problem (some files may be is no longer available)
Mini091109 - 01.dmp
SysData. XML
Version.txtSee a temporary copy of these files
WARNING: If a virus or other security threat caused the problem, open a copy of file can harm your computer.Additional information about the problem
BCCode: 1000008e
BCP1: C0000005
BCP2: 8A90628F
BCP3: 9CCAEDB0
BCP4: 00000000
OS version: 6_0_6001
Service Pack: 1_0
Product: 768_1
Information about the server: 7ec0ad43-82ec-418c-af58-c7d4e1d1d9e8copied and pasted this information of view problem history in Control Panel and it was the biggest mistake, what happened is that the PC I use suddenly gets a blue screen with big writings saying something like she stops by unexpected error. After rebooting, it says "Windows has recovered from unexpected shutdown" and gives me a chance to see solutions on the net, but the work does'nt. Fortunately, I don't have an error for hours, but I'm afraid it may happen again. Please help me.
My laptop has:
AMD Athlon processor
1 GB of RAM
1.60 Ghz
ATI Radeon X 1250
Windows Vista
120 GB hard drive (33 GB free now)I think that the mistake occurred whenever I might have too many applications open, especially in the section of the status bar, that I can't do it, please help me!
Thank you.Hello
Think the drivers - do all.
Could be a nuisance pilot. Update your drivers manually looking at system manufacturer and
Sites of the manufacturer of the device.This is my generic how updates of appropriate driver:
For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
This will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
own the software and drivers and all other main drivers that you have.Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
(Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.
Always check in the Device Manager - tab drivers version you install actually shows up. This
because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
pilot - reboot - check that it is installed and repeat if necessary.Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.
Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlIf you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
manually if you wish.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspxHope these helps.
Rob - bicycle - Mark Twain said it is good.
-
Hi people I have some hard drive problems, please help :)
Hi guys, I just bought a Sata HDD internal 2 TB, but I do not see it in 'my computer', but when I go to computer management I see, I tried to do something with it, but an error pops up, I treid deleting and creating a new partition, but just before the end, I get this error : "The operation failed to complete because the disk management console view is not updated. Refresh the view by using the refresh task. If the problem persists close the disk management console, then restart disk management or restart the computer. "Please help. TNX
Did you try to restart and try again as he proposed? Assuming that you I had two ideas. First of all, if your system is not aware of Windows updates, I would now. Secondly, I have had good success called Easeus Partition Master that you can download from http://easeus.com . I see they have a page for a free version 9.1 for users running the environments of 32 and 64 bit to http://www.partition-tool.com/personal.htm .
I hope this helps. Good luck.
-
Windows 7 blue screen problems, please help me
Hey guys, I'm using windows 7, my laptop these past two weeks have blue screen problems. When I boot my laptop, and I use internet after some cell time but I have a blue screen with MSG (Message Details: to your computer. igdpmd64.sys PAGE_FAULT_IN_NONPAGED_AREA)
If this is the first time that you have, "
Please help me, there are the details:
Signature of the problem:
Problem event name: BlueScreen
OS version: 6.1.7601.2.1.0.768.3
Locale ID: 1033
More information about the problem:
BCCode: 50
BCP1: FFFFF8811C177B60
BCP2: 0000000000000000
BCP3: FFFFF880067A5A18
BCP4: 0000000000000005
OS version: 6_1_7601
Service Pack: 1_0
Product: 768_1
Files helping to describe the problem:
C:\Windows\Minidump\042414-20155-01.dmp
C:\Users\manjeet varsha\AppData\Local\Temp\WER-37752-0.sysdata.xml
Read our privacy statement online:
http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409
If the online privacy statement is not available, please read our offline privacy statement:
C:\Windows\System32\en-US\erofflps.txt
Here is an article describing how your problem may be related to a bad Windows Update.
KB2670838 update uninstall can solve the problem for you.
-
BlackBerry Smartphones BB APP WORLD v. 1.1 PROBLEM - Please HELP!
I am a new user/owner of a BB Curve 8330. In the options screen, it said c. 4.5.0.77 (Platform 3.2.0.51). I'm not sure what these numbers correlate exactly with (operating system, software device, etc.)-pathetically.
This morning, I tried to upgrade to the new version 1.1 BB App World. I think I can get screwed up. When I installed it, it asked me if I wanted to remove the 1.0 version, and I said 'yes '. After installation of v. 1.1 and rebooting, I tried to use the new version and I always get the following error message:
"BlackBerry App World is had problems connecting to the server BlackBerry App World. Check your network connections, and then try again. »
My phone is not compatible with this version? I can't understand. I was going to download the 1.0 version and reinstall, but I can't seem to be able to find this version available for download.
Please help - I don't know what to do.
Thank you in advance,
TDS
PS: by the way, I know my network connections are fine. Everything works as it should.
Here's the answer to the question I was trying to Irdawg a Newbie CrackBerry.com:
Model: Curve 8330
-
Table and the loop problems (please help)
Im making a site for a project where I have to include a table and a loop.
For this section, I put in a "contact us / Q and A" page where the user can enter a name, email, and question.
This information is sent to a table and then following image shows the form of the table information in the dynamic text boxes.
I've included a loop to check that each part of the table contains data (name, email and the issue).
Then I have an If Else, which clears the form either if a section has been missed, OR if the form was completely correctly it directs the user to the frame following where as I said above the details appear in dynamic text boxes.
The problem im having is the loop to check For the table that's a waste. Someone can please help me out here and get the loop to verify that all fields have been filled.
Here is my code for the initial frame
You must update the values in your table at the time you press the submit button. Code follows
There is a second example to check the strings (it's a little complicated, but it's a useful trick if you can understand). This does not leave the Send button work unless all fields have something in them
-
Hi all I just brought a laptop from pc world and there no battery sothey gave me money to buy one, but I can't find an anywere is a nightmere is a compaq presario a935em
P/N KU062EA, someone got any idears and I have verified that hp and compaq sites please help
Thank you very much
HP parts... (800) 227-8164
Contact HP:
-
I have a problem, please help me
I have a leptop I buy. This leptop is the Windows operating system.
My label to the back of Breackfast is not clear, I don't see it clearly
know there's other way get my product key Home Premium.
This my Leptop Modul:PC portable Compaq Presario CQ42-269TX
[S/N deleted]
Product number: WZ588PA #UUF
Please Help me I need my Procuct Key to the label to recover my Windows operating system
[Personal information]
I have a month.
My highlight number I don't know what that number might be that I need.
Under writing HP
and as scan code (line, line)584043 001
Please help me.
This is a forum for peer to peer and members here help each other voluntarily. Please see the link below in order to contact HP
http://WWW8.HP.com/my/en/contact-HP/phone-assist.HTML#section -
Help, please. Security problem please help. ___
Another person in the apartment where I live has put its media player as an icon in my taskbar without asking. Please help me to make sure that it is impossible to do it again
Thank you for your time and effortMake sure your firewall is on and Security Center Windows to check and make sure that everything is green, if there is something red or yellow then see what he wants. Make sure that you use the version of anti-virus update and update your Windows and antivirus. If you use try Wi - Fi to enable WPA2 or WEP 128, see the manual of the wireless modem.
As AntiVirus, you can use Microsoft Security Essentials for free
Scan with your antivirus complete and remove the threat. use of strong passwords for your Windows login, create strong passwords have look at:
https://www.Microsoft.com/protect/fraud/passwords/checker.aspxTry to go to the BIOS Setup and disable the boot with CD and network and make sure you boot from the hard drive is turn on and rest are disable. (Check your BIOS manufactor to aid)
If you are using Windows Vista Ultimate using Bitlocker
Remember, if you choose password of Windows to the top, because if he has lost or forgotten, we cannot help you. In Windows, you can backup password.
Remmember back up your data before password and put weekly or daily backup policy that if something is wrong you have backup (it is a good idea but a backup external hard drive). Windows Vista have already great backup feature.
-
BlackBerry Smartphones Re: 9360 Curve problem please help!
An error occurred contacting the client BlackBerry World. If you have a content protection enabled on your device, please disable and try again. the same message that I get when connecting my laptop... Please help me
I think that you... I think that you have tried. But, from what you say here, I have no idea exactly what you have tried. There are the specifics... The KB numbers would help. But telling us just what you have said so far we, we cannot say anything on what you actually tried and therefore cannot give you next steps as we have need to exclude what you have already tried. But you need to tell us exactly what you have tried (even once, would help the KB numbers).
Please consider that we have only your words to guide us... nothing more than that. So far, your words have all the details to help us understand what you have already tried. I think you you tried something... I have no idea what it was.
Thank you and let us know.
-
TWO PROBLEMS, please help me, I'm on a dead line, which was held yesterday.
I want two fields unrolling to connect. When I click on the first and say click on cards, I want the other to put only the sizes for the cards. When I cilck on Brochures, I want the other to get only sizes for brochures. I did a test with the send e-mail button. When potential clients receive not, I want that they fill out the form and just be able to send it right back to me. Well after I filled out the form and tried to submit it, a box pops up and asked what kind of e-mail account was I trying to send it with, and then he made me save and attach myself to an e-mail. Is there a way to get to where when they press on submit, they won't have to go through all this? Please help me I'm on a deadline. I guess I have this done yesterday. I have attached the form... Thank you
Here you go...
See the attached document. The solution is simple. I had to make a few simple changes in the 'DropDownListScript' script and add the JS code in the event of changing the drop-down list item. Now it's working.
Also I added the new button next to your button to submit by e-mail. This a normal button but it does the same thing you want using script. Check the script to the title of the "click" event However to avoid, it will ask you what mail client, it assumes to use you need to set up some things before you try...
For IE browsers...
1. right click on the IE icon and choose Properties.
2. open the "Programs" tab
3. find the value in E-mail: box... it must match with your e-mail client.
For example: it could be "MS OutLook" or "Lotus Notes"...
Note1: He folds on each individual when computer is not fixed will be guest like the one you saw. There are therefore no control over that.
Note 2: However, you must assign additional user rights to complete and submit this form. With that I guess that you only see blank form when someone sends you e-mail.
-
ADF 11 g: create with the data control problem: Please help
Hello
In my application, I tried to create a customized data controller.
I created a Java class results and a bean ResultsBean class.
Then I selected class results-> right click-> data controller to create.
The Results.xml is created
Everything is going well so far.
Then I updated the details of class Bean in Results.xml and tried to re-create the data controller but did ResultsBean.xml ' t formed.
In other words ResultsBean have not associated with outcome data controller.
Please help on this.
Version of the ADF: Studio Edition Version 11.1.1.3.0
Build JDEVADF_11.1.1.3.PS2_GENERIC_100408.2356.5660
Thanks and greetings
Maryline RousselYes you use generics to the JDeveloper type, how the JDeveloper Assistant know the ResultBean is used to return an ArrayList value?
Maybe you are looking for
-
How to get rid of the 'MyStartSearch '?
38.05 Firefox Whenever I start Firefox, the default search engine is set to 'MyStartSearch '. After setting the default in Options of Google search engine and the removal of the 'MyStartSearch' in search engines, Firefox it changes mysteriously to "M
-
Not good at El Capitan Snow Leopard: which goes back?
Well, I'm in trouble, I think. I have improved my Early 2008 iMac (2.4 Ghz 4 GB ram) machine of 10.6 Snow Leopard to El Capitan (reason: so I could save my new iPhone6s - was not recognized in iTunes in 10.6). What is OS El Capitan somewhere cool, bu
-
Equium A100-549: burn your own movies on a disc
Hello someone knows how I can playridebikehike movies on a disc? I can get them on Windows movie maker nut, then when he tries to burn it says an unknown error occurred when recording on a disc, and it's a whole new disc can someone help please?
-
HP Touchsmart All In One Printer
One of the black ink cartridges has been removed from my printer and not replaced for a few months. Now that I have replaced all the ink cartridges, an individual does not have 'view' when I finished a test print. I ripped out the Ribbon and follow
-
Can it 64 supprt 64 bit games graphics card
Original title: Please help Hi I want to play a rom c d with a 64-bit requirement, I have 32 bytes, but due to the upgrade if I buy a 64 graphics card I'll be able to play my other games