Best practices for cloning a VM ESXi

Similar Questions

• Best practices for storing the Logs of the system for all newly improved ESXi hosts?

  Hi people,

  What are the options and best practices for the Logs of the system for all newly improved 5.1u1 ESXi hosts?

  Do I need to have the Syslog server or it can be safely ignored?

  Thank you

  Evening,

  Syslog is preferred, but VMware has provided a collector of syslog on the vcenter installation disc can be installed on any windows host or your vcenter. I can't count the number of times where I had guests CMTF or newspapers lost... Fortunately for the syslog which collects up to the accident.  It is not necessary, but it's really a good idea without any real cost since you can use your vcenter host.

  Here is an article on how to install it:

  Set up Syslog ESXi collector | VMware vSphere Blog - VMware Blogs

  Thank you

• Best practices for vsphere 5.1

  where can I find the doc more up-to-date about berries EQL configuration / best practices with vmware vsphere 5.1

  Hello

  Here is a link to a PDF file that covers best practices for ESXi and EQL.

  Best EqualLogic practices ESX

  en.Community.Dell.com/.../20434601.aspx

  This doc mentions specifically that the storage Heartbeat VMKernel port is no longer necessary with ESXi v5.1.  VMware has corrected the problem that made it necessary.

  If you add it to a 5.1 system it will not hurt.  It will take an IP address for each node.

  If you upgrade 5.0 to 5.1, you can delete it later.

  Here is a link to VMware which addresses this issue and has links to other Dell documents which confirm also that it is fixed in 5.1.

  KB.VMware.com/.../Search.do

  Kind regards

• Best-practice for hardware virtualization?

  Hardware virtualization is disabled by default when I create new virtual machines in my VMware clusters. But what are the best practices for this what settings are recommended? Are there reasons NOT to activate the hardware virtualization?

  IMO there is no advantage in allowing virtualization of hardware if you have no need for the virtual machine (for example, a virtual host of the ESXi).

  André

• Best practices for network configuration of vSphere with two subnets?

  Well, then I'll set up 3 ESXi hosts connected to storage shared with two different subnets. I configured the iSCSI initiator and the iSCSI with his own default gateway - 192.168.1.1 - targets through a Cisco router and did the same with the hosts configured with its own default gateway - 192.168.2.2. I don't know if I should have a router in the middle to route traffic between two subnets since I use iSCSI ports linking and grouping of NETWORK cards. If I shouldn't use a physical router, how do I route the traffic between different subnets and use iSCSI ports binding at the same time. What are the best practices for the implementation of a network with two subnets vSphere (ESX host network: iSCSI network)? Thank you in advance.

  Install the most common iSCSI would be traffic between hosts and

  the storage is not being routed, because a router it could reduce performance.

  If you have VLAN 10(192.168.1.0/24) iSCSI, VLAN 20 (192.168.2.0/24) ESX

  MGMT and VLAN 30 (192.168.3.0/24) comments VMs and VLAN 40 (192.168.4.0/24)

  vMotion a deployment scenario might be something like:

  NIC1 - vSwitch 0 - active VMK (192.168.1.10) MGMT, vMotion VMK (192.168.4.10)

  standby

  NIC2 - vSwitch 1 - current (VLAN30) guest virtual machine port group

  NIC3 - vSwitch 2 - active VMK1 (192.168.1.10) iSCSI

  NIC4 - vSwitch 2 - active VMK2 (192.168.1.11) iSCSI

  NIC5 - vSwitch 1 - current (VLAN30) guest virtual machine port group

  NIC6 - vSwitch 0 - MGMT VMK (192.168.2.10) standby, vMotion

  VMK (192.168.4.10) active

  You would place you on VLAN 10 storage with an IP address of something like target

  192.168.1.8 and iSCSI traffic would remain on this VLAN. The default value

  gateway configured in ESXi would be the router the VLAN 20 with an ip address of

  something like 192.168.2.1. I hope that scenario help set some options.

  Tuesday, June 24, 2014 19:16, vctl [email protected]>

• Best practices for HP DL385p G8

  Trying to find documentation for the implementation of a HP DL385p G8 for VMware Server. I would like to find a guide to best practices for this server? Been looking for but not found anything. I would like to find things are should hyperthreading turned on and so on. I use the ESXI from HP image for pilots, that all work but just want to find the settings.

  Thank you

  Hello

  you will find on this blog: BIOS settings in a VMware ESX (i) / vSphere environment. VirtualKenneth & #039; s Blog - hqVirtual | Quality rental a detailed explanation on all the BIOS settings and why you should enable or disable it.

  hope that helps.

• What is the best practice for a 'regular' Server VMware and VDI environment?

  What is the best practice for a "regular" VMware Server and VDI environment?   A single environment (ESXi and SAN) can accommodate two if it is a whole new configuration?  Or even better to keep separate?

  Enjoying inputs.

  Quick and dirty answer is that "it depends."

  serioulsy, it depends really two things budget and IO.  If you had the money for two without then buy two and don't have to host your server environment and the other for VDI desktop, their IO profiles are completely different.

  If this is not the case, try to keep each type of use for their own dedicated LUN.

• Best practices for managing strategies of path

  Hello

  I get conflicting advice on best practices for managed paths.

  We are on version 4.0 of ESXi connection to a HP EVA8000. Best practices guide HP recommends setting the strategy of railways handle on Round Robin.

  This seems to give two active paths to the optimized controller. See: http://h20195.www2.hp.com/v2/GetPDF.aspx/4AA1-2185ENW.pdf

  We used certain consultants and they say that the best practices of Vmware for this solution is to use the MRU policy which translates a single path to the optimized controller.

  So, any idea what good practice is best practice? Does make a difference?

  TIA

  Rob.

  Always go with the recommendation of the storage provider.  VMware recommendation is based on the characteristics of the generic array (controller, capable ALUA failover methods, etc.).  The storage provider's recommendation is based on their performance and compatibility testing.  You may want to review their recommendations carefully, however, to ensure that each point is what you want.

  With the 8000, I ran with Round-Robin.  This is the option of creating more robust paths available to you from a failover and performance point of view and can provide performance more even through the ports on the storage controller.

  While I did of the specific tests/validation, the last time that I looked at the docs, the configuration of HP recommends that you configure each IO to the ports in the switch configuration.  This adds the charge to the ESX host, the switch to other ports, but HP claims that their tests showed that it is the optimal configuration.  It was the only parameter I wondered in their recommendation.

  If you haven't done so already, be sure to download the HP doc on configuring ESX and EVA bays.  There are several parameters that you must configure the policy path, as well as a few scripts to help make the changes.

  Virtualization of happy!

  JP

  Please consider awarding points to useful or appropriate responses.

• AF best practices for video

  I'm using an EOS 7 d for 1080 p HD video shooting. New to SLR camera and digital video. I have watched several tutorials but do not yet have a good understanding of what the best practices for the development.

  If I put the camera in AI Servo it will auto focus if the subject is moving away or toward me with depress me back AF-ON or the shutter button? Or should I press one of these buttons to make the camera continues to focus?

  You know tutorials or video lessons that cross using update with the video?

  Thanks in advance!

  I don't know any tutorials, but more serious videographers say it is best to use only the manual focus.

  Trial and error is a good teacher, when it comes to video DSLR. You'll quickly learn that video Auto Focus is really bad with the 7 d and most of the people do not use it all together.

  The method that works for me is to use AF before the filming of the video and then adjust manually if you want to you to shoot the video. With the help of f/8 or f/11 to keep everything in short without having to keep the setting.

  More recent Canon DSLR's like the T4i, T5i, 70 d and SL1 have a "hybrid AF" that does a much better job of AF during video, but it is not yet as good as a camcorder

• I would like to know the "best practices" for unplugging my computer permanently to the internet and other updates.

  Thank you for taking the time to read this. I would like to know the "best practices" for unplugging my computer permanently to the internet and other updates. I thought I would do a clean install of Windows XP, install my Microsoft Works again and nothing else. I would like to effectively transforming my computer into a word processor. He continues more and more slow. I get blue screen errors, once again. I received excellent Microsoft Support when it happened before, but since my computer is around 13 years, I think it is not worth the headache to try to remedy. I ran the Windows 7 Upgrade Advisor, and my computer would not be able to upgrade. Please, can someone tell me how to make it only a word processor without updates or internet connection? (I already have a new computer with Microsoft Windows 7 Home Premium, it's the computer that I use. The old computer is just sitting there and once a week or so I updates.) I appreciate your time, thank you!

  original title: old computer unstable

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/install-Windows-XP

  http://www.WindowsXPHome.WindowsReinstall.com/sp2installxpcdoldhdd/indexfullpage.htm

  http://aumha.NET/viewtopic.php?f=62&t=44636

  Clean install XP sites
  You can choose which site to reinstall XP.

  Once it is installed, then you do not have to connect what anyone, however, some updates may be required to perform the work, test this by installing work and see if you get an error msg. Except that you should be fine.

• HP stream 11-d008tu: best practices for migrating to Windows 10?

  Hey there, I have a HP flow 11-d0008tu and received the notification I can upgrade to Windows 10. I want to do a clean install with a downloaded ISO but knowledge first of all, it is better to upgrade so that you get the activation done.

  Can someone give me some ideas on best practices for the upgrade? The stream has only 30GB HD so I have no recovery disk, I'll just do a recovery later on USB or SD card. When I do the upgrade can deselect recovery option or delete?

  Also, any other suggestions appreciated, especially which helps make effective for small HD

  See you soon

  Hi, I posted an installation procedure for Windows 10 fresh for the Tablet HP Stream here.  Also, I have a laptop 11 flow but do not have that yet. I think it must be the same because they both the same drive of mem 32 GB Hynix. A change would you probably want to use the 64-bit instead of 32-bit Windows 10 ISO file, the Tablet has only 1 GB of RAM.

• Just improved m tips on best practices for sharing files on a Server 2008 std.

  The field contains about 15 machines with two domain controllers, one's data is the app files / print etc...  I just upgraded from 2003 to 2008 and want to get advice on best practices for the establishment of a group of file sharing. Basically I want each user to have their their own records, but also a staff; folder. Since I am usually accustomed to using windows Explorer, I would like to know if these actions can be done in the best conditions. Also I noticed on 2008 there is a feature of contacts. How can it be used? I would like to message or send an email to users their file locations. Also, I want to implement an admin at a lower level to handle the actions without making them far in on the server, not sure.

  I read a certain bbut I don't like test direct more because it can cause problems. So basically a way short and neat to manage shares using the MMC, as well as the way that I approach their mail from the server of their actions. Maybe what kind of access cintrol or permissions are suitable also for documents. Also how can I have them use office templates without changing the format of the model.

  THX

  g

  Hello 996vtwin,

  Thank you for visiting the Microsoft Answers site. The question you have posted is related to Windows Server and would be better suited to the Windows Server TechNet community. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• [ADF, JDev12.1.3] Best practices for maintaining a form validation

  Hallo,

  in my application, I need to create a registration form which contains fields that must be validated (for example they should follow a format like e-mail, phone number, tax code,...).

  If the data inserted by the user are ok, a new record in my custom db table Users will be created.

  I would like to know which are the best practices for maintaining the validation, which means the place where the controls must be made and a message to the user who fills out the form when something goes wrong.

  The best vo or EO or managed bean? Or some controls should be put in the OS, others in the VO and other in the managed bean?

  I would be happy if you could give me some examples.

  Thank you

  Federico

  Assuming you want the validation on the value of the field to any screen data can be entered in (and possibly web services that rely on the same BC ADF) then put the validation on the definition of the attribute in the EO.

  If you want to add a little more friendliness and eliminate some of the network traffic to the server, you can also implement the validation client in your page - for example by using the regular expression validator.

  https://blogs.Oracle.com/Shay/entry/regular_expression_validation

• Best practices for color use in Adobe CC?

  Hi all

  Is there an article that describes the best practices for use of color in Adobe CC?

  I produce a mixture of viewing online (PDF, for the most part) and real world print projects - often with the obligation for both. I recently updated my PANTONE + bridge books for the first time in ages and I am suddenly confused by the use of Lab colors in the Adobe Suite (Illustrator and InDesign).

  Everything I found online, looks like Lab color mode preferred to use because it is device independent. And perceptual (on screen), it looks much closer to the color, it is trying to represent. But when I mark a Spot color Illustrator rectangle using laboratory coordinates, to the sides of a rectangle using PANTONE + bridge CP and then export it to PDF, the version of CP to mix CMYK color corresponds exactly to my Pantone book - while the version of laboratory (after converted to CMYK using the ink Manager) is far away.

  I have this fantasy to manage only a single Illustrator or InDesign file for both worlds (PDF) printed and online. Is not possible in practice?

  Any info describing the basic definitions of the color modes - or even a book tracing more than use them in the real world - would be much appreciated!

  Thank you

  Bob

  Here are a few best practices you can already do.

  1 make sure that your color settings are synchronized on all applications.

  2. use a CMYK profile appropriate for your print output. Lab spot colors convert to CMYK values based on the CMYK icc profile.

  3. include icc profiles when save or export pdf files

  In theory, your imagination is possible today. It requires color management and the use of icc profiles. You can place RGB images in InDesign and use Pantone colors in your objects. The problem lies in the printers. If a printer uses a RIP with built in Pantone library, the colors will match when printing. Unfortunately, this kind of CUT is more expensive and not enough printers use them. Most of them is always manually approximate CMYK values composition given Pantone colors.

• Best practices for managing exceptions and success messages.

  Hey people,

  These days I've been shooting packages to clean my application. And question came to my mind, ' should I treat my exceptions the right way?

  
  So I want to ask you met guys, what is the best practice for this? (I want to learn it until it's too late )

  Currently I have a function that returns "OK" if all goes well.

  
  

  return('OK');  

  Can I manage my exceptions like this

    EXCEPTION
      WHEN OTHERS THEN
        ROLLBACK;
        RETURN (SQLERRM);
  
  

  At THE SUMMIT, I have a process that calls the function and then checks if the function returned "OK".

       IF cRet not LIKE 'OK%' THEN
        RAISE_APPLICATION_ERROR(-20000,cRet);
       END IF;
  
  

  And in 'process Error Message' I put "#SQLERRM_TEXT #" so that I can see what error occurred.

  Question aside, how do you manage your messages of success?

  Currently in 'process success Message' put something along the lines "Action completed successfully". What to do about all the processes.

  Do you want to do differently?

  I really want to hear what you have to say since I'm tired of feeling like this is a terrible way to manage these things.

  Hi Para,

  Para wrote:

  I don't know of situations where my service throw exceptions like no_data_found.

  and I need to know that the process is not so I can get to see my # #SQLERRM_TEXT.

  I got this by increasing the error in the application (which I think is a bad way to go) if the return is anything other than 'OK '. I get my application error in the process of the apex, and not in my service.
  And I want to show the inline error in the notification. (Which I am currently with my approach).

  You can use APEX_ERROR. ADD_ERROR in your PL/SQL process to throw exceptions in Oracle APEX.

  Reference: Re: Re: error in the processing of the page management

  Kind regards

  Kiran