Can PlayMemories control several cameras AS15-HDR?

Similar Questions

• Control several cameras with Codec C60

  Hello:

  I have a client who wants to use 3 PrecisionHDMC cameras and with the intervention of content to a codec C60, as well as an AMX control system.

  I understand that there may be only 3 video inputs connected to a C60 both, my question is:

  If I have a HDMI switch which video switches of 3 cameras connected to Video Input #1 the C60 and have that is configured as an input of the CAMERA, how to control the cameras independently?

  I usually sign my AMX for the C60 system RS-232 and send an order which said in effect "Hey C60, 1 camera to zoom before saying" or "Hey C60, say camera 2 to zoom out, etc...

  But in this case, the C60 will be only 'think' it has a camera connected, therefore:

  Can I still send commands via the codec that say things like 'hey C60, say 2 camera to zoom out,'

  OR

  I can "daisy chain" cable between them and simply connect RS - 232 to the 1st chain camera and tell them '' camera 3, zoom ''?

  OR

  Need me a RS-232 connection distinct to each camera and just say "camera zoom out.

  I hope I explained my question quite well, I look forward to your responses!

  Thank you!

  If you want to integrate a bit more flexibility and discreet control, you can add a small matrix of switching in the project (see Extron DXP 44 HDMI) and have then each camera connected directly to the AMX for control. This allows the discrete control, discrete video selection, output preview and the ability to also have a PC or other video source connected (3 cameras and a PC).

  Discrete control is possible with chaining with addressing, but according to the placement of the camera and the distances between the camera the Garland cable runs can a problem and since you have to run the video towards the grid it's easier to run the control back on location as well.

  If you want to use the composting and then the TC console should be used.

• Premiere Pro CC - waveform I can synchronize with * several * camera and audio clips a Pluraleyes the?

  Many of us use Pluraleyes to synchronize the DSLR and 2nd audio WAV files using waveforms. (No timecode.)

  The ability to synchronize in first Pro CC has been mentioned in several lists of feature, but I don't see the ability to synchronize a clip at a time.

  Y at - it no way to align several MOV and WAV files with different start / stop times and no other another match that of waveform and synchronize them automatically in first Pro CC in a sequence (or by creating multiple merged clips)? In other words, can I reproduce the Pluraleyes features in this new version of Premiere Pro?

  Currently, the best way to do it is by selecting all items in the project Panel, right-click on it and select Create multi camera source sequence.   Synchronization via audio, choose your audio settings (if you want audio in both clips, select all cameras), and then click ok.  Blocking is smart enough to make this batch and make several sequences of MC with only the clips that match each other.  Unfortunately merged clips, or timeline sync will do only one at a time.  If you want this behaviour in amalgamated sync of clip or timeline, please file a feature request: https://www.adobe.com/go/wish

• HDR-CX240... How can I get the camera to record all FILES VIDEO in MP4 format?

  HDR-CX240... How can I get the camera to record all FILES VIDEO in MP4 format. Is this possible? I can't find how to change what default file to save to. Any help would be appreciated.

  Hi dang201,

  There is no option to save the video in mp4 format only. You can check on the MProot folder on your memory card for mp4 files. The. MTS files are normally saved in another folder called flow.

  If my post answered your question, please mark it as "accept as a Solution.

• The movement of my robot can be controlled by the entry of a camera control in labview?

  I'm new to mindstorms and I'm trying to interface a camera that I can easily control in Labview with the NXT unit movement.  I want this to be real time.  What is the best way to get Labview to send commands that get immediately updates implemented by unity NXT?  Thank you.

  Sorry - fact.  Thank you.

• Hi am gift, I can't find the window of several camera on first cc 2015

  Hi am gift, I can't find the window of several camera on first cc 2015

  you serve CS6 first which has the separate several camera window. First CC has multiple camera monitor in the program monitor. Click on the "key" icon and choose the multiple camera in the menu drop-down

• You can control several subforms (6) show/hide drop-down list

  Hi, I'm trying to get a drop-down menu to control the 6 options of subform

  List values

  1 = no value = 1

  2 = 1 value = 2

  3 = 2 = 3 value

  4 = 3 value = 4

  5 = 4 value = 5

  6 = 5 6 = value

  five forms

  codno1, codno2, codno3, codno4 (each a numeric / date)

  and codno5 (a notice of revision)

  I want javascript to the output/change of difficulty? event from the drop-down list

  something like that...

  but I'm not a programmer and not sure how to structure properly - any help/pointers please!

  I can get it to do the premiera with { }

  if (this.rawValue == '2')

  cod1date. Presence = 'visible '.

  }

  {

  if (this.rawValue =='3')

  cod1date. Presence = 'visible' & & cod2date = 'visible ';

  but when I try to control several subforms that it breaks...

  I thought that something like below makes sense...

  If this.rawValue is 6

  codno1. Presence & & codno2.presence & & cono3.presene & & codno4.presence & & codno5.presence = 'visible ';

  otherwise if

  this.rawValue == 5

  codno1. Presence & & codno2.presence & & cono3.presene & & codno4.presence & & 'visible' = & & condno5.presence = 'hidden ';

  otherwise if

  this.rawValue == 5

  codno1. Presence & & codno2.presence & & cono3.presene = 'visible' & & codno4.presence & & condno5.presence = 'hidden ';

  ElseIf... And so on...

  The syntax of your function that is not correct. You missed the quotation marks around the value of test and the break statements.

  var A = this.rawValue;

  Switch (A)
  {
  case "5":

  break;

  case "6":
  cod4date. Presence = "visible";

  break;

  case '4 ':
  cod3date. Presence = "visible";

  break;

  case '3 ':
  cod2date. Presence = "visible";

  break;

  case '2 ':
  cod1date. Presence = "visible";

  break;

  /*

  You can also have default parameters too:

  */

  by default:

  }

• Cannot connect AS15-HDR for Android Smartphone

  Hello

  I'm trying to connect an AS15 HDR to my smartphone to control as described in the user manual.

  I have PlayMemories Mobile installed 2.1.1 on my race stock Samsung Galaxy Note II (GT-N7100) Android Jelly Bean 4.1.1

  I set the unit as described on page 39 of the user manual, I have PlayMemories installed and running. I can see the camera (LIVE - BFH0:HDR - AS15), I get the password, I select the device and after about 20 seconds, the app reported: "failed connection".

  Is there a solution to this problem?

  Thank you

  Hi, the problem has been resolved with the latest update to play memories 2.2.0.

• Recommend products OR for my application (controlling several instruments at the same time)

  I'm new to Labview, currently only using the trial version.      There is money in my budget to buy control software, but I need to qualify my needs.

  What I try to do is to control several pieces of equipment to test as a single system, which allows me to perform automated on conventional measures

  and digital two way radios.

  Here is a list of the material I want to control:

  First of all, my controller is a & Rohde Schwarz 3 PSL.   Fully GPIB active and ready.  It is the PC control software will reside on.

  Equipment:

  Spectrum analyser Rohde & Schwarz FSEA 30 with modulation analysis package digital option B7

  FSEA 30 second, same configuration

  R & S AMIQ4 I / modulation generator Q (files of the software residing on the PSL3)

  Generator of analog signals from R & S SMY 02

  Agilent E4431B analog-to-digital signal generator

  Agilent E4406A spectrum analyzer/digital radio test set

  E4418B Agilent RF wattmeter with sensor

  General Dynamics R2670B service monitor

  A typical application will be a test of classical radio on VHF or UHF analog channel.

  The idea is to enter pass and receive frequencies through Labview or any software is best suited for the job, as well as modulation parameters.

  and have the following things occur: assume usage of 150,000 MHz with a FM frequency modulated 1 kHz sounds modulated to the deviation of 2.5 KHz

  in total, with your 127,3 Hz subaudible to a gap of 300 Hz

  Test phase of receiver: send commands to control of instrument of Agilent E4431B signal generator.   Level set to-60 dBm.  Set to 150,000 MHz frequency.  Set

  Audio 1 to 1 KHz and audio tone 2 to 127,3 Hz at a level of 8 pecent of your 1.  SD total do not exceed 2.5 KHz.      Inject the test signal into port RX

  on the radio.

  The value R2670B SINAD function, related to the radio via the audio output port.

  Signal level to ramp down to the SINAD falls to 12 dB.

  Increase the level of the signal to the attenuation of 20dB.   Measure the audio distortion.

  Testing of transmitter: using the attenuators appropriate necessary on the analyzers of spectrum, and/or using a switched network of wiring.

  place radio to transmit using above specifications frequency and modulation.    Analyzers to receive on the frequency designated value

  and measure the transmitter specifications, including nonessential radiation measurement and harmonics.    Measure actual output power

  Via E4418B-power meter.

  I use two monitors to perform multiple tests in a same transmission. One is optimized for spectral purity tests while

  the other analysis of modulation characteristics.    Frequency, duration and RBW are defined according to the needs.

  When you test a digital radio, the signal chain is slightly different.  The AMIQ I / Q modulation generator s I / Q outputs are sent to the

  I / Q inputs on the Agilent generator, the power is on to accept external I / entered Q and the FSEA Spectrum Analyzer (an a)

  the) is passed to a preset that implements all relevant digital parameters so that it can be used to directly evaluate the digital transmissions.

  It is not a very developed in the planning system, but I do not know now whether Labview is everything I need or if I'll need to Teststand or another

  software packages.

  I'll probably want to ask for some advice on how to get this set up, eventually.

  LabVIEW is more than capable of this task. That's what it was designed to do. Use the help > find the instrument Drivers to find and install the drivers that you can use to control and read.

  TestStand generally requires the use of a programming language. It runs the tests that you write and provides functionality built for the production of record and report database then you would need to write these modules yourself with LabVIEW fair and some add on box to tools. For a single test configuration, it is perhaps an exaggeration, but it is interesting to watch as an addition.

• Several cameras for machine vision

  We would like to use Vision Builder I do Visual inspection of our products. Due to the large size of the object, we might need several cameras

  to do this. Is it possible to use information from several cameras to Vision Builder or do I have to use several constructors of Vision at the same time? Are there

  other solutions?

  Kind regard

  Bert

  Certainly, Vision Builder AI can handle the acquisition of several cameras. If you trigger the cameras, the software can process even the images that have been acquired at the same time (although sequential processing steps, the step of acquiring image can be synchronized with other CQI steps if necessary for your application).

  The software includes templates to illustrate several different architectures of camera (see the new Template Inspection option under the new Inspection during the creation of a new inspection of the splash screen), and here are a few documents area dev that may also be useful:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/6864

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/6368

  Hope this helps,

  Brad

• How can I change several download Sierra systems

  How can I change several download Sierra systems?  I have a Mac mini end of 2012 running El Capitan, over a mid-2010 Mac mini and MacBook Pro mid-2010 the two race Yosemite with limit of bandwidth on my internet connection and want to update all three systems in one download.  Is the process that apply with Yosemite and El Capitan (ie. Copy the Setup program to another location before you run it on the download system) still the way forward?  Thank you.

  You can do this or DiskMaker X allows to create a key to install it.

  (145170)

• Can't access my camera back im. IM can access before comera that too of facetime.

  impossible IM to access rear camera in my iphone 5s.im measure only camera before that too of facetime.

  Hello

  Try the steps here:

  Get help with the camera on your iPhone, iPad or iPod touch - Apple Support

  (Note that, as you can access the front camera via FaceTime, the problem is not related to Restrictions).

• I can not control "get messages".

  I just installed Thunderbird on Windows 7 64-bit.
  I have connected to my e-mail from Virgin Media.
  However, Thunderbird is downloading the messages in batches of 100 from 2009, the next day I am until August 2013.
  How can I control the dates and receive messages? I'm happy to say the past 24 months only.
  How to get all messages and not an arbitrary bock about 100?
  Help!

  Another possibility if POP mail account:
  http://KB.mozillazine.org/Download_only_certain_POP_messages

  read the article "Automation what message body are downloaded.

• How can I control the list of the available in the message SSL Client Hello cipher suites? I want to ban the MD5 and RC4.

  How can I control the list of the available in the message SSL Client Hello cipher suites?
  I want to limit my browser to negotiate the cipher suites fort. I would like to prohibit, MD5 and RC4.

  Set the SSL3 preferences related to false on the subject: config page (filter: security.ssl3.).

  • http://KB.mozillazine.org/about:config

• Satellite Pro has - can not control the brightness level

  I can't control the brightness level of the screen of my laptop! When I opened (Panel\Hardware and Sound\Power Options control) I can't find!

  Hello

  Usually, you can change the brightness of the display by using the FN + F6/F7 key combination.

  It works for you?