Connections limited to the OPA

Similar Questions

• Wireles connection limited after the fashion watch

  Can someone help me understand why I can't connect wireless when my computer wakes from sleep? It connects only to 'restricted access' and I have to disconnect and reconnect to get it working.

  Hello

  Have you tried just uncheck the box "allow the computer to turn off this device to save power" in the Wireless Network adapt/properties/Configure/Power Management menu?

  It is enabled by default I think!

• Windows 7, not identified limited in the wireless network connectivity

  I have a Vostro 1720 laptop for about 1.5 years and up to a month before, its connected fine just internet Best Western (my place of work). All of a sudden it just stopped and started giving the message "limited connectivity". I tried many commands and procedures that have worked for others, nothing is. My final straw was to wipe completely and to upgrade my vista to Windows 7 (Home ed). Now my computer is running 7, but still the problem remains. I tried:

  1. Manually assign an Ip address
  2. Reset the Modem
  3. Disable the Ipv6 Protocol
  4. Flushing DNS
  5. running Internet explorer without modules
  6. Commands (netsh int ipv4/ipv6 reset reset.log) Winsock stack
  7. Stop and start the DHCP service
  8. Looking for the ##ip - list services – found nothing
  9. Looking for Hello in the list services – found nothing
  10. Uninstall and reinstall the drivers
  11. from the identified public/no network to private - changed back
  12. Save, and then change the reg edit {GUID} - does not, so I changed it back
  13. Wipe the hard drive and the installation of Win 7
  14. At off Norton Antivirus completely (removal tool)
  15. Running in mode without failure + network
  16. Turned off the firewall in windows 7 by default
  17. Allocating an address random MAC under Advanced properties in the wireless card driver
  18. Disable all connections except for the wireless connection

  Hi all

  I had the same problem and searched for 2 days for a reply.

  I'm under Intel Centrino Wireless n 1030 in Windows 7.

  I finally found an updated driver for the Centrino Wireless n 1030. It has been updated 5/2011 which was more recent than the version 12/2010 I had on my computer.

  http://www.driveridentifier.com/scan/download.php?item_id=51625129&ScanID=6BEF4EB662F14B20B13ACCD8D322B6A9&hardware_id=PCI%5CVEN_8086%26DEV_008A%26SUBSYS_53258086

  When you log on the site it says that! This driver is not designed for your computer!, but I downloaded and installed in any case.

  HE FIXED EVERYTHING!

  I hope this helps...

  Lindsay

• I can't connect to the internet. "Connectivity limited or not. Seems to be the Winsock error. __

  Symptoms

  • Internet connection icon indicates: "connectivity limited or not.
  • When I try to run Internet explorer, I get "Internet Explorer cannot display webpage".
  • When I run "Diagnose connection problems" I get the following Diagnostic log indicating a Winsock error:

  • Diagnosis of last run time: 21/11/09 10:31:47

    WinSock diagnostic

    WinSock status Info Error attmpting to validate the Winsock base providers: 193 error Not all base service provider entries could be found in the winsock catalog. A reboot is required. Info Redirect the user to support call

    Diagnosis of network adapter

    Network location detection Info Using the Internet connection at home Identification of network adapter Info Network connection: name = Local Area Connection 3, device = Broadcom 440 x 10/100 Integrated Controller, MediaType = LAN, type = LAN Info Network connection: name = wireless network connection, Device = Intel (R) PRO/Wireless 3945ABG Network Connection, MediaType = LAN, type = Wireless Info Network connection: name = 1394 connection, device = 1394 Net Adapter, MediaType = LAN, type = 1394 Info Connections Ethernet and wireless available, ask the user for selection action User input required: select network connection Info WiFi selected State of the network adapter Info The network connection status: connected

    HTTP, HTTPS, FTP Diagnostic

    HTTP, HTTPS, FTP connectivity warn HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved warn HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved warn FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved warn HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved warn HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved warn FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved error Could not make an HTTP connection. error Could not make an HTTPS connection. error Could not make an FTP connection.

  • Have tried resetting winsock.
  • No problem with wireless router - it works on other computers.

  Help!  How to fix it.

  Ice22Man,

  To reset the Winsock settings automatically, click the fix it button or link. Click run in the file download dialog box and follow the steps described in the fix it Wizard.

  Solve this problem 
  
  Microsoft Fix it 50203

  Note this wizard may be in English only; However, the automatic fix also works for other language versions of Windows.
  Note if you are not on the computer that has the problem, save the fix it solution to a flash drive or a CD and then run it on the computer with the problem.

  To manually reset Winsock for Windows Vista, follow these steps:

  1. Click
  

  type cmd in the Search box, right-click cmd.exe, click run as administrator, and press continue.

• Type netsh winsock reset at the command prompt and press ENTER.

  Note If the command is typed correctly, you will receive an error message. Retype the command. When the command is executed successfully, a confirmation is displayed, followed by a new command prompt. Proceed to step 3.

• Type exit and press ENTER.
For more information about resetting Winsock, see the following Microsoft KB article: http://support.microsoft.com/kb/811259
Hope that helps!

Cody C
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite P750 - no WIFI connection in all the

  Have had a new Satellite P750 for 2 weeks. Some intermittent problems, wireless modem connection - now no link at all. Connects to the modem with "limited activity" - so no internet. It connects ok with the modem cable. Have rebooted, checked the driver updates. No idea what to do to solve this problem. My first Toshiba and I'm really not happy I lost my money!

  Any help?

  Hi Brettd,

  > now no link at all. Connects to the modem with "limited activity".
  This confusion of s. At the moment you have no connection or limited? Both is not possible ;)

  I recommend an update of the WLAN driver and you can download the latest driver WLAN here:
  http://APS2.toshiba-tro.de/WLAN/

  Also, make sure that MAC address is not blocked in router and update the firmware on your router.

• No internet connection after installing the update of security for Windows Vista

  Security updates for Windows Vista released October 13, 2009 and November 10, 2009 still an Internet connection limited Connectivity/No. Did not help uninstall updates. To do the system restore to solve the problem. Why is this?

  drusecord,
  First thing is to update your network drivers for your system.  Then see if after the update of safety, you have a problem.  If you do, I would do the following:

  Disk error checking

  System File Checker

  Then if there are updates that you already have, but are always available to consult this information:

  Troubleshooting Windows Update: offered on several occasions to update

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I reset or fix my router wireless or (lost the ability to connect wirelessly to the internet) access point

  Wireless hub works, other computers are connected

  On a laptop, I lost the ability to connect wirelessly to the internet (message: limited connectivity)

  Recommended by the system solution: reset or repair your access point or wireless router

  How can I do?

  I think that what you aim for is "power cycle".

  To do this, simply unplug the router/access point power adapter. Wait a minute. Then reconnect it.

  Hope this helps

  Post back if necessary

  ___________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows vista local access only or limited to the Internet

  I have windows vista on a dell insipirion laptop, purchased in January 2009

  It came with mcafee anti virus already installed, that I removed after the test free and replaced with norton 360
  I use the modem usb 3g for my access internet and had no problems for 6 months

  for about 2 months, I had problems with connecting to and browsing the internet

  My 3 States of modem usb connected with good signal window
  but internet explore cannot display web pages

  the icon at the far right of the taskbar displays access: Local only

  If I click on this and open 3 modem status, under the general tab it has...
  Local IPv4 connectivity
  IPv6 limited connectivity

  If I click Properties, click the Networking tab
  Protocol version 6 (TCP/IPv6) Internet is not always checked
  I check this box, dissconnect 3g, re-connection 3 g, go back to the box to find still uncontrolled

  I have connectivity limited for some time before it becomes local only for awhile, then it finally gives me access to the internet for a short time before going back to local only access. the only thing I can do is to disconnect and reconnect and hope to have online long enough before again losing connectivity internet limited or local connectivity

  IV a 3g send me a new modem
  so have uninstalled and reinstalled the modem

  Reference Dell helped me to put the laptop into the factory State

  Reset all settings to internet explore and disabled all add ons

  diagnostic tells me that I have a problem with one or more network cards, but dell tell me im using a usb modem if it isn't the network cards that have the problem

  Please someone help me to heal this problem of limited connectivity and local only access before going bald of pulling my hair

  Hello Gemzy,
   
  Thank you for choosing Microsoft answers forum for windows vista.

  There are several things that we can try to solve this problem.

  Let's start by disabling all other connections to try to force the wireless connection to request the information needed in the router.  So go to start > Control Panel > network and sharing Center > manage network connections.  Click on each link listed EXCEPT the wireless LAN connection, then click on disable this network device.  Then see if your wire will connect.  You may run the diagnostic and repair utility on the Network and Sharing Center menu to force the wireless card to request information from the router IP.

  If all else fails, go back into the network and sharing Center, manage network connections and right click on the wireless network connection and select Properties.  Then click Internet version 4 Protocol and select Properties.  Click in the box that says "Use following IP address" and enter the information that has been shown in IPCONFIG report for your connection to the Wired Local network above.  Do the same for "use the following DNS servers."  Make sure that you type the IP address, mask subnet, default gateway, and DNS addresses exactly the same than the connection to the Local network was when he got the information from the router.

  To learn more about how to troubleshoot network connection problems, see the link below:

  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  If none of these things work let us know and we will continue to help you.

  Kind regards

  Savan - Microsoft technical support.

• Router WRT54G3G-ST - no internet connection - cannot reset the router

  Hello.  Some longer story certainly not short (I apologize for the length of hiking...  I don't know what is and isn't important, will scan, please...  I'm sorry...) : recently my computer (Dell XPS 400, Windows XP Service Pack 3, Internet Explorer 7 with phishing filter and pop-up blocker on, SiteAdvisor, up-to-date McAfee Anti-virus and Firewall and a router Wireless-G Linksys WRT54G3G-ST with its AC adapter plugged into the wall power outlet and a network cable directly connected to my computer.) received a drive-by generic.DX!12536d125737 Trojan horse without me download whatever it is one of the few sites I visit every day.  My internet connection has crawled, and I have now no connection at all.

  I've been making McAfee good volunteers forums help quick and very helpful...  They recommended Malwarebytes Anti-Malware for me, I downloaded my own second computer (a laptop) on my flash drive, then on my infected computer.  I ran, tried adapting so recommended, and only then discovered the Trojan horse killed my broadband entirely.  I scanned with it anyway and he quickly found and deleted / quarantine 11 Adware.MyWebSearch related files, but nothing else.  Then, they gave me a link to a patch off updater file and tells me scan in SafeMode until nothing else has been found and check if it has fixed my lack of broadband access.  I did, Malwarebytes found nothing else, but unfortunately I still had no broadband.

  Then, they recommended WinsockXPFix.  Which I ran and he did all his OK registry changes, I restarted if necessary but still no broadband unfortunately.  WinsockXPFix using make things worse for me with the registry changes, did he?  I used the backup of the registry to save the registry before changed files before running.  Should I come back since I don't always have a broadband connection?  McAfee volunteers kindly then told me that I had to hard reset the router, but I tried many times with no fortune.  I'm at a loss as to what, if anything, do we hope to get my broadband, please...

  It is very confusing with many different variants for resetting routers, and what should I do to my router model (Variations: unplug this cable/adapter exactly where; pressed the reset button between 5 and 30 seconds, the computer restarts, or no, 1 or 2 minutes between different steps, waiting or not - and for all these exactly when in the restart procedure.).

  I have reset once before with the reset button, page of routers to http://192.168.1.1default admin password, then it changed to security, etc. but this time I can't make it work.  I'm happy as possible to try once again to get an appointment by perhaps, something please...  When I go to http://192.168.1.1 now, or to any other address, Internet Explorer gripes at me that I am offline, which is annoyingly correct.  I do not have and never had Zone Alarm, but disable my McAfee Firewall does not help.  IPCONFIG at the command prompt gives me an address of 169.254.X.X assigned Windows

  I was going to use the routers Wizard installation CD to try to reset the router, and if that didn't try to get its firmware version number to perhaps upgrade.  But I was going to ask here first of all for expert advice because I read a lot of things that can go wrong during the upgrade of the firmware.  However, analysis the CD (without launching the CD). McAfee found the virus W32/HLLP. Philis.ini in the file "D:\_desktop.ini" on the CD.  McAfee didn't delete the file, I don't know why.
  I scanned my computer together several times and no infections have been reported.  I downloaded the file several times, both www.virustotal.com (39 online antivirus) and virusscan.jotti.org (20 online virus scanners) and every time each virus scanner didn't report any possible infection.  My updated virus scanner McAfee reported a false positive and still Jotti and VirusTotal 2 scanners from McAfee report the file as own probable?  Is "_desktop.ini" a file legitimate Linksys?  I have not found any information on Linksys forums about this.  My problems just keep multiplying... mentioning problems more...

  Find this suspicious file on the CD I decided to download instead the Linksys Setup Wizard
  (Router product page: http://www.linksysbycisco.com/US/en/support/WRT54G3G-ST/download )
  File: http://downloads.linksysbycisco.com/downloads/WRT54G3G-ST_SetupWizard_4_2_06042008.zip)
  my flash drive, then on my infected computer that is connected to the router.  I ran it (downloaded the version of the file: 4.2.0.007 - original version CD Setup Wizard: 4.0 print on CD front) and immediately gave it 1 of the 3 options: Mobile broad band only, high flow only WAN, or WAN high throughput and high speed Mobile.  I don't know what damage, if any, I caused by continuing.
  It seemed that he was trying to go in the entire router configuration process.  I thought it would take me to some options to reset the router, as I read in the user's Guide, and besides - it is my understanding.  The installation process stopped at only 30% done "router not found, make sure that the router is connected correctly and try again."  How many Overwrite original router configuration files I did continue?  I'm quite confused.  The wizard does not check if the router has previously been set up before setting up again?  Unlike version caused my router to not be detected by the Setup Wizard?  Is the horse of Troy generic.DX!12536d125737 who killed my trash to wide band my computer settings so badly that my router is undetectable/essentially not configured?

  Update of sorts: I tried one last time to reset the router, and I unplugged/plugged the network cable.  The fact that I had still no broadband on my Dell XPS main use computer that is connected to the Linksys router.  However, my laptop, with map data in the router, was for the first time able to find network - constant connection and speed is great, it's what she allways has been on the laptop (the Trojan/router problems, my laptop only for broadband with the data in the laptop card.).  Perhaps the cable network was simply not re-connected properly/entirely for 1 of the many attempts of resetting, indeed, it could also explain the downloading, installation wizard is not able to find the router/only get 30% done.

  Laptop prompt IPCONFIG/all with data card Sprint inserted into the slot of your laptop:
  IP = 174.158.XX.XXX (Sprint)
  Subnet mask = 255.255.255.255
  68.28.90.91 = DNS servers
  68.28.82.91

  Laptop prompt IPCONFIG/all with Sprint data card inserted in the router:
  192.168.1.1XX = IP address
  Subnet mask = 255.255.255.0
  Default gateway = 192.168.1.1
  = 192.168.1.1 DHCP server
  Servers DNS = 192.168.1.1

  Since my laptop started to work with the data card into the router, I have not tried again to reset the router and I tried the downloaded installation wizard.  I don't want to spoil anything about it any further as I have (?) / the Trojan has, and I need expert advice, please, about which of the 2 if not more, I do (first?).  On my laptop, typing http://192.168.1.1 in Internet Explorer Gets the ToolTip for the user name and password, but I did not.  I read that you should not reset the router or (?) Is it just 1 or two please?) upgrade the firmware unless the computer is connected directly to the router - that is not my laptop.  On my other computer that still has no broadband, Internet Explorer still says I am offline when you type http://192.168.1.1 in.  My IP address on it is still a 169.254.X.X assigned Windows and a command PING 192.168.1.1 prompt returns with 'Destination host unreachable.', as it has been always and even with all the other addresses (with the exception of 169.254.X.X).

  Boring 2nd "update" of all kinds, my apologies for the length, as always: I've been so focused on the horse of Trojan/broadband killing that cluelessly largely forgot I switched with AOL.  Try AOL dial-up does not work, madness thickens...  Software AOL tells me to check my connection, but all the phone cords are connected as should be.  I plugged a phone directly into the wall jack and I get the tone, I can call OK and the phone rings and receives calls OK.  State of the devices-Modems-Properties-Device Manager says that the modem is not working properly, and "resources" tab shows no conflicts.  Query Modem on the diagnosis tab seems OK to me, as does the journal, but I'm certainly not an expert like allways.  I change all the settings from anywhere.
  I noticed and that check IPCONFIG it says that my IP address is 192.168.1.100 it lasts maybe that someday (then goes back to 169.254.X.X), maybe more, I don't know - I don't check that often to define (should I?).  Meanwhile my broadband, or my works switched.  I can PING 192.168.1.100, but nothing else.  I am convinced the wrong killed Trojan horse my broadband and dial-up - I've never had a problem with my prior V.9x DFVc Modem 56 K Conexant D850.  In addition, I am not convinced the Trojan horse is not still lurk everywhere on my computer, I think that it's...

  Any help with the restoration of my high speed/dial-up is greatly appreciated, please...  Thank you!

  Hello.  There has been entirely too long since I answered, I'm sorry.  There is no excuse, and it is terribly rude to me...  You took the time to read and answer me, and I appreciate very much that in effect.  I apologize for being late, I'm sorry...

  After that I left my message, I downloaded several virus/spyware scanners, etc from my laptop on my USB key, then my other computer for some in-depth analysis necessary.  Was one I downloaded Network Magic that somehow, some way fixed both my high speed/dial-up internet on my main computer is connected to the router WRT54G3G-ST.  I don't know what/how he fixed my connection, but the connection high speed flow works brilliantly since...  Network Magic has worked for me, and I highly recommend it to all those who have stubborn lack of internet problems (caused by Trojans to this) that I did.  There is no guarantee this will work, but it did for me in my amazement.

  Network Magic, as is the Linksys is owned by the parent company Cisco.  Respectfully to all the knowledgeable experts here (which clearly I'm not), I don't want to venture out of the limits.  I'm trying to simply hope to be useful and save a few headaches for both you volunteers and users... buy a new router or the computer was in my mind, with all due respect, I recommend suggesting to try Network Magic users if the reset of the router/all other fails, please.  I used WinsockXPFix/WinsockFix utility before using Network Magic, I don't know if it matters.

  I also upgraded my package of McAfee, I installed on my old software rather than uninstall the first, which caused errors in all things virus scanner a critical need.  I install right now, but it caused some delay to refocus my time.  Some virus scans found many Trojan horses, some were same / in the same folders that killed my broadband - which stopped me in my tracks to ensure a clean uninfected.

  Certainly, it doesn't fully explain the long time, and I'm sorry, once again.  It's just that I'm being cautious and slow in all this.  To answer the first very good idea, you did: Unfortunately, there is no room on my other computer to connect the router in to, which even so caused frustration (at the time).  I forgot to include this in my post new length of countless things to see / do not forget...  It was a brilliant idea, however, I thank you...

  Thank you for your time and your help, I appreciate it sincerely...  Thank you...  I think and hope that this matter is resolved.  It seems to be, the router works perfectly as it always has, and I am positively happy as can be in this regard.  Thank you...  Peace...

• Receive error message when adding the control of signature on the screens of the Interview with the OPA

  Hi team,

  We have an obligation to add electronic signature on multiple screens of interview.

  I tried to add the control of Signature in the form of the interview, but I get the error message below. We use the OPA 12.2 version November cloud.

  "Current data mapping settings do not support file attachments. File upload controls is no longer valid. (OPA-E00538)

  Thank you

  Vivek

  Yes. And make sure that you submit to a Service Cloud FileAttachments active or item by using a connection to the web service that supports attachments for the entities mapped on a.

• Why im getting this error: "ORA-22813: value of the operand exceeds the limits of the system.

  HI EXPERTS...

  Please helpme to fix this...

  I have a database of oracle 11g, runnint on a Windows Server 2008:

  Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production

  I have two tables:

  CREATE TABLE UTILS. SEG_ROLES

  (

  VARCHAR2 (12-BYTE) APPLICATION,

  ROL VARCHAR2 (12-BYTE),

  USERS VARCHAR2 (255 BYTE)

  )

  TOGETHER TO DEFINE

  Insert into SEG_ROLES (APPLICATION, ROL, USERS) Values ('MULTIPLAN', 'ADMIN', 'ADMIN');

  Insert into SEG_ROLES (APPLICATION, ROL, USERS) Values ("MULTICLIP", 'CAR01', 'PATY');

  Insert into SEG_ROLES (APPLICATION, ROL, USERS) Values ("MULTICLIP", "CAR02", "FABIOLA, ERIKA");

  Insert into SEG_ROLES (APPLICATION, ROL, USERS) Values ("MULTICLIP", "CON01', 'LUCY, PATY');

  Insert into SEG_ROLES (APPLICATION, ROL, USERS) Values ("MULTICLIP", 'CON02', 'VALERIA');

  COMMIT;

  CREATE TABLE UTILS. SEG_ACCESOS

  (

  VARCHAR2 (12-BYTE) APPLICATION,

  ADMROL VARCHAR2 (12-BYTE),

  VARCHAR2 (20 BYTE) MENU,

  OPCION VARCHAR2 (20 BYTE),

  TYPE VARCHAR2 (5 BYTE),

  OBJETO_MENU VARCHAR2 (40 BYTE),

  ACCESO VARCHAR2 (2 BYTE),

  ROLES_ACCESOS VARCHAR2 (255 BYTE)

  )

  TOGETHER TO DEFINE

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "ROOMMA", NULL, am', 'm_coloca', the of ', 'CAR01, CAR02');

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "PUT", "PREVALIDA", "SM", "sm_prevalida", the from ', 'CAR01, CAR02');

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "PUT", "PRECOLOCA", "SM", "sm_preColocacion", the from ', 'CAR01, CAR02');

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", 'ADMIN', 'LOVE', "COLOCACIÓN", "SM", "sm_colocacion", the from ', "CAR01");

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "PUT", "REGCOLOCA", "SM", "sm_regcoloca", the from ', "CAR01");

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "LDP", NULL, am', 'm_PLD', the of ', "CAR01, CAR02, CON01 CON02");

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "LDP", "LN_CONSULTA", "SM", "sm_PLD_LNConsulta", the from ', 'CAR01, CAR02');

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "LDP", "LN_BARRIDOMASIVO", "SM", "sm_PLD_LNBarridoMasivo", the from ', "CAR01");

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "LDP", "REP_INICICLO", "SM", "sm_PLD_ReporIniciclo", the from ', 'CON01, CON02');

  Insert into SEG_ACCESOS (APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS)

  Values ("MULTICLIP", "ADMIN", "LDP", "LN_BITACORA", "SM", "sm_PLD_LNBitacora", the from ', "CON01");

  COMMIT;

  - And this point of view:

  
  

  CREATE VIEW UTILS. VW_ROL_USER AS

  Select distinct APPLICATION, ROL, trim (column_value) USUARIO

  from (SELECT APPLICATION, ROL, USERS USER

  FROM UTILS. SEG_ROLES

  WHERE IT IS NOT NULL TO USERS

  ORDER BY APPLICATION, ROL

  ) t,.

  XMLTable ((' «' ||)) Replace (USER, ",", "",""). '"'))

  order by APPLICATION, ROL, trim (column_value)

  CREATE VIEW UTILS. VW_ACC_ROL AS

  Select distinct APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, trim (column_value) ROL

  (SELECT APPLICATION, ADMROL, MENU, OPTION, TIPO, OBJETO_MENU, ACCESO, ROLES_ACCESOS ROL

  FROM UTILS. SEG_ACCESOS

  WHERE ROLES_ACCESOS IS NOT NULL

  ORDER BY APPLICATION, ADMROL, MENU, OPTION

  ) t,.

  XMLTable ((' «' ||)) Replace (ROL, ",", "",""). '"'))

  MENU, TYPE, OPTION, APPLICATION control, trim (column_value)

  CREATE VIEW UTILS. VW_SEG_ACCESOS AS

  SELECT VACR. APPLICATION, VACR. MENU, VACR. TIPO, VACR. OPCION, VACR. OBJETO_MENU, VACR. ACCESO, VACR. ROL, VUSR. USUARIO

  FROM UTILS. VW_ACC_ROL VACR,

  UTILS. VW_ROL_USER VUSR

  WHERE VACR. ROL = VUSR. ROL

  ORDER OF VACR. APPLICATION, VACR. ROL, VACR. MENU, VUSR. USUARIO, VACR. TIPO, VACR. OPCION

  When I ask the last posting, it works fine:

  SELECT VSEG.* IN UTILS. VW_SEG_ACCESOS VSEG

  But when I add conditions:

  SELECT VSEG.* IN UTILS. VW_SEG_ACCESOS VSEG

  WHERE VSEG. APPLICATION = "MULTIPLAN.

  AND VSEG. USER = 'PATY '.

  It generates this error:

  ORA-22813: value of the operand is greater than the limits of the system

  Cause: The value of the object or the Collection was too big. The size of the value might have exceeded 30 k in a context of TYPE, or size may be too large for the available memory.

  Action: Choose a different value, and try the operation again.

  Why?

  Thanks in advance...

  Finally found a SOLUTION at: http://stackoverflow.com/questions/14328621/oracle-10g-splitting-string-into-multiple-rows

  just change the way we create the view using the regexp_substr.

  CREATE VIEW UTILS. VW_ROL_USER AS

  SELECT distinct trim APPLICATION, ROL, (regexp_substr (USERS, ' [^,] +', 1, level)) USER

  FROM UTILS. SEG_ROLES t

  WHERE IT IS NOT NULL TO USERS

  CONNECTION BY instr (USERS, ',', 1, level - 1) > 0

  order by APPLICATION, ROL

  Thank you all

• Limitation of the APEX: sharing pages between several APEX applications

  I was hoping if someone with a little more experience architect APEX could comment on some of the limitations that I see and I have to make good decisions, working around the problem.
  
  Any suggestions are welcome.
  
  One of the limitations I've seen, it's how APEX handles applications and pages. Each application appears as an island, it has its own set of pages, the processes of connection, templates, CSS, JS, references etc.. Regarding the CSS and Javascript, you can be defined in a central location, but still, every new developed APEX application must be configured to make use of your 'standard '.
  
  The more traditional web solutions showing each as stand-alone web page and any web page can call/reference any other page and pass information to session between them.
  
  With APEX, however this doesn't seem to be the case.
  
  A solution would be to have a huge demand for APEX, where all the pages are the property of this unique application.
  
  Unfortunately, we use of APEX and EBS R11 (& R12) together; all APEX applications are started in the menus of the EBS. I had drawn a SSO solution between the two (without using oracle SSO). However, each APEX application is unique, as small modules instead of complete applications. In other words, we tend to use APEX as an alternative for Oracle Forms - each APEX application is a standalone program.
  
  I always wanted to be able to apply the same connection process and look and feel in the brand new APEX app we write.
  
  The way I went to this subject has been meticulously creating a 'model' APEX application. Embedded in the application of this model are all our shared CSS, JS and models that apply the site appearance. It also contains our custom library of signature unique code and debugging custom logger (think log4j but for APEX).
  
  So whenever a developer began work on a new APEX application, they start by cloning the model and automatically inherit all the functionally and website presentation.
  
  My concern is if this is really the best way to do it, or if I'm missing something?
  
  I am also concerned move forward when I wants to establish the change in appearance across all of our web applications that I need to touch each APEX application since. I'm trying to mitigate this by ensuring that almost all the programming logic is contained in packages of PL/SQL, CSS and Javascript only referenced and external application of the APEX. But this does not always with models, or with a logic that is rooted in the actual pages of the APEX etc.
  
  At least APEX allows you to easily enough copy pages between applications, but it does compare not just to have a single page shared between all applications of the APEX.
  
  Is there a better way to go about this?

  Hi attis.

  I think you can't really compare a module with an APEX application forms. I wouldn't say to create an APEX application every time when you have created a module of forms in the past.
  A forms module is just a few pages of an application to the APEX. Then you really should have more then a few pages in an APEX application. Certainly, a huge application is also not the way to go, but I group them for example by logical areas such as HR, logistics, order...

  As Sc0tt already mentioned, you must use the 'Subscribe' mechanism of shared components to make it easier to update all your applications with the model updates. But there is more, you should also share your user name and just have in one place and use the "simple APEX based SSO" that allows all applications within a workspace can share the same session. Simply set the 'Cookie' namesake in your authentication for all your applications and when you bind an application to another and include a valid session id you should not have to log in again and you can also set the session state in that other application.

  So here's what I'd do

  (1) creating a master application that contains
  (a) your theme and other components shared that you want to share
  (b) must be also some basic navigation lists to navigate between your applications...
  (c) create a sign with the name "Redirect to connect main app" and type accounts APEX (no matter) where you define the name of 'Cookie' to 'Cbx_missmost' and the URL of invalid session to the login page of your creation 'hand connection app '. For example: f? p = 9999:101: & SESSION.

  (2) create a model application which is a copy of the claim, but where change you the "subscription" of your models, authentication scheme and components shared in the main application. This will serve as your App developers if they want to create a new application.

  (3) create your 'hand connection app' (eg. app 9999 id) by
  ) a copy of your new model application
  (b) remove the inside authentication scheme (this is just made for this main connection app)
  (c) create a new type to use. But important: set the name of 'Cookie' to 'Cbx_missmost '. This will ensure that all applications have the same session cookie.
  (d) If you use APEX 4.1.1 you will automatically be redirected to the calling application after successful login.

  (4) start to create new applications by copying your 'model' application that contains all subscriptions.

  (5) If you run this application, it automatically redirects to your main connection application if the current session is not valid. This will avoid to have the same logic of authentication in your applications.

  (6) If you need to change your templates or shared components you just do in the "master" application and click on the "publish" button to push the changes for all your applications.

  But still, try to avoid many small applications, I think that make handling just unnecessarily complicated. It is an APEX application has a few hundred pages. For example, our APEX app Builder (app 4000) has more than 1260 pages.

  Concerning
  Patrick
  -----------
  My Blog: http://www.inside-oracle-apex.com
  APEX Plug-Ins: http://apex.oracle.com/plugins
  Twitter: http://www.twitter.com/patrickwolf

• How to connect database DB2 to OPA?

  Hello
  
  I m new to OPA. I am trying to connect with the OPA DB2 database so that I can move forward with the writing of the rules. I m not able to find the exact method. There is a way to use the option import to XML... But it's not clear exactly how... Any help would be great here...
  
  Thank you...

  Shenoo,

  We have nothing specific to OPA 10.3 (or earlier) to read and write data to and from a database. We provide java and APIs .NET which allow you to write a program that can connect to a database, push the data to get the answer of the OPA, rewrite in the database, but all we provide that the rules of logic there.

  He next version 10.4. We have plans to release a new batch processor which will allow you to run rules on a database tables and write the results back to the database, or to a file. 10.4 isn't out yet, but it currently in beta and is not far away.

  See you soon
  Frank

  Published by: frank.hampshire on February 20, 2012 12:35

  Published by: Davin Fifield, February 22, 2012 22:55

• Siebel field values are not passed to the OPA: error on WD Smoke Test

  Hello
  
  I installed OPA siebel connector locally and deployed determination determination of web and server to tomcat server. The 'DS smoke Test' button works well, but the 'WD Smoke Test' does not work correctly. After the installation by clicking on the button opens a pop-up window with "page cannot be displayed".
  
  I changed the symbolic for 'Employee' as URL:
  
  http://localhost: 8085/siebel-web-determinations/startsession/AdminSmokeTest
  
  (from the original one: http://localhost:8085 / siebel-web-determinations/startsession/AdminSmokeTest/en-US? user = [UserID] & caseID =, [UserID], [ObjectID], AdminSmokeTest)
  
  This show opens the popup window and and it asks the question ' what is the text of valid user?' by clicking on it application "which is a Siebel Admin user's first name?" then the subsequesnt questions and after the last questions it shows if it is valid Siebel Admin record ot not. If the rule works correctly.
  
  Now my questions are:
  1. how the Siebel field values will be passed to the determination of the Web? Ideally result response (if that's a record valid sadmin) should have been displayed in the window pop up directly by clicking on the button 'WD Smoke Test' with the employee field values passed, instead he asks for input.
  
  2. the field mappings are definde in the automation of the Admin-Policy-> show mappings. The field values are passed correctly to the server of determination, but how to pass for determination of the Web? The same mapping works for the determination of the Web as well?
  
  3. If I use the old url for employee (http://localhost: 8085/siebel-web-determinations/startsession/AdminSmokeTest/en-us? user = [username] & caseID =, [UserID], [ObjectID], AdminSmokeTest) the user id is passed correctly but it is throwing an error.
  
  4. in the Administration - policy Automation-> Web determinations it gives the following error.
  
  [An error occurred when loading the case ID "8SIA-82CJP, SADMIN, AdminSmokeTest".
  This error has been recorded and is available in the application logs.
  
  Support and assistance please contact [email protected]].
  
  If I change the url as before, then he asks the same questions. What is this point of view?
  
  Thanks in advance!
  
  Kind regards
  ALIOU

  ALIOU,

  One of the key things to note about the OPA Web determinations for Siebel is which is needs component EAI run on the Siebel server for it to work. There is an article on this in the installation guide where there you preform a test to verify that EAI_ANON_ENU is running on the Siebel server (located on pages 12-13 on the installation guide).

  1. for determinations of Web works properly, you must leave the URL token exactly as indicated in the installation guide. In addition, determinations Web use EAI (mentioned above) to pass information to the Web of Siebel determinations.

  2. same as number 1.

  3. again once it goes back to check that the EAI runs.

  4. make sure that the user you are logged in as has the responsibility to use this point of view.

  In addition to all this... once EAI works you need to check the incoming Web Service URL and point them to the location of the IAE but also change the path to the IAE in the file data-siebe - adapt .properties. Also, be sure to match the user name and password in this file for what you use to connect to Siebel with.

  -Adam Starr

• Features of limitations for the folios on the part of the Adobe viewer

  Hello

  The limitation on the use the same Adobe ID with the viewer Adobe for 25 devices start now? with V25. I didn t find these information in this link - What's new in this version

  Concerning

  __Felipe

  There is no limitation as such, but multiple connections do inetefere with your account performance. If you have a large number of pages in your account, it is advisable to avoid too many connections has a single application. So I would keep the low number of connections unless you have an ID specifically for sharing folios for several people to control.