create the second with WRT54GL wifi network?

Similar Questions

• No network from the list of available WiFi networks :/

  Freshly installed Windows 7 32 bit in laptop HP AMD 6 with all of the necessary drivers, but no network on the list of available WiFi networks.

  Uninstalled the drivers, re installed them but still the problem persists. Also test the resolution of problems. No positive results.

  Please someone tell me the procedure from the beginning to the end for the connection!

  Hey Phillipe,

  Please contact Microsoft Community. I appreciate your efforts to solve this problem, I'll probably help you solve this problem.

  To better understand the issue, I would like to know what is the number of full model of the laptop?

  Try the steps listed here:

  Method 1:
  I suggest you to run the network troubleshooter utility that will help solve Internet connectivity problems.

  Network convenience stores
  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Method 2:
  I see that you have uninstalled and reinstalled the driver for the wireless network. However if you haven't tried re-installing latest driver on the computer manufacturer site wireless, I suggest you to try the same thing. Check if it helps.

  http://WWW8.HP.com/us/en/drivers.html

  See the article for more information.

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• Windows 8 user unable to connect to the public AT & T Wifi networks (McDonald's, Starbucks, FedEx desktop, etc.).

  I searched here and I have not found anyone else with this issue, but I can't be the only one.

  In the event that I am the first, my problem is that I can't connect to the public AT & T WiFi networks; McDonald, being the most common location.  It appears in the list of wireless networks, but it takes forever for the McDonald's to open web page in the box that says something like "Connect to the Internet" or words to that effect.  Finally after clicking this check box, a message appears at the bottom of the page indicating that the webpage is not responding; Click to refresh it.  No matter how many times I try it, nothing happens.

  I have Windows 8 on a Toshiba Satellite.  It's a new laptop comes with Windows 8; No updates to otherwise than to buy this new laptop.

  What is strange, is that I am on a WiFi network at the moment.  "Wandering WiFi" to be precise.  But I tried to get on AT & T at Starbucks earlier this evening and had the same success that I had at McDonald's.

  I'm pretty sure that I don't mess with settings wireless on my pc but I can't say that for sure 100%.

  Sorry to see that you are having problems. Please, try the following.

  Restart the device

  Make sure that all the updates have been applied.

  • Open the network connections Panel
  • Select the network connection corresponding to either right click (mouse) or hold by selecting (finger).
  • A Context Menu will appear. Please Select forgotten network.
  • After the network connection is dropped, please reconnect.

  If that solves the problem then great! If this is not the case, let know us and we will try something else.

• How to create the table with the description of the table

  Hello

  I would like to create the array with the description of the table (such as the creation of package or procedure with comments).

  Is it possible to achieve thanks to the oracle, if possible please help me achieve this goal.

  Thank you and best regards,

  Ibrahim Sayyed.

  > create table test (col1 number);

  > comment table test is "about a comment ';

  > select comments from user_tab_comments where table_name = 'TEST ';

  COMMENTS
  ____________________________________________________________________
  This is a comment

• Create the database with a set of characters

  Hello
  
  I need to create a database with the character US8PC437 (platform Linux Redhat 5.4 64-bit, database version 11.2.0.3), but this character set do not appear when I create the database with the database assistant (DBCA).
  
  Any help will be apreciated.
  
  
  Best regards
  
  Antonio Serrano
  
  Published by: albrotar on March 6, 2012 09:14

  While AL32UTF8 is certainly recommended for the Oracle database character set, use only, if your application provider has confirmed that their application will work with a set of characters to multibyte database.

  To create a database US8PC437 (it is rarely a choice, in fact) with DBCA 11.2, select the "character sets" tab, once shown, then select the option 'Choose from the list of character sets' and uncheck 'Show recommended only character sets '. This will add US8PC437 to the "Database character set" drop-down list. Select "US8PC437" from the list and continue the process of creation.

  But first, contact your provider and ask a compatible Unicode version of your application.

  -Sergiusz

• Creating the table with time stamp

  I need to create the table with the data inside buffer
  
  Can you help me pls
  
  If it works today,
  
  create the table test_04NOV2010 in select * from product where product_code = '101'
  
  If executed tmrw,
  
  create the table test_05NOV2010 in select * from product where product_code = '101'
  

  declare
  
  v_date varchar2(25);
  v_sql  varchar2(20);
  
  begin
  
  select to_char(sysdate,'DDMONYYYY') into v_date from dual;
  
   v_sql := ' create table ' ||TEST||'_'||'v_date'|| 
               ' as '
               ' select * from Product where product_code = '101'
            
   EXECUTE IMMEDIATE v_sql;
  
  end;

  can is it you pls let me know how to use it in PL SQL
  
  Can you help me pls
  
  Thank you very much

  declare
  
  v_date varchar2(25);
  v_sql  varchar2(2000); --Noted this. this was also small.
  
  begin
  
  select to_char(sysdate,'DDMONYYYY') into v_date from dual;
  
   v_sql := ' create table TEST_'||v_date||
               ' as select * from Product where product_code = ''101''';
  
   EXECUTE IMMEDIATE v_sql;
  
  end;
  

  You can use the Q operator also.

  DECLARE
  
  v_date varchar2(25);
  v_sql  varchar2(2000);
  
  BEGIN
  
  select to_char(sysdate,'DDMONYYYY') into v_date from dual;
  
   v_sql := ' create table TEST_'||v_date||
              Q'[ as select * from Product where product_code = '101']';
  
   EXECUTE IMMEDIATE v_sql;
  
  END;
  

  Published by: mohamed on November 4, 2010 05:32

• Samsung wireless surround does not work with Airport wifi network

  I have a smart tv with a Soundbar and wireless - all Samsung two speakers. I should be able to set up surround sound via the network wireless like this http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx= 629802 & modelname = WAM7500 & modelcode = WAM7500/ZA

  It works fine when it connects to the router provided by my ISP sky. But when I try to do the same when connecting to the network created by the airport, it won't work no-more precisely, I'm unable to select "link Multiroom' (step 19 in the link above).

  Note: There is no problem connecting to the wifi network - it's this last step which is the issue.

  Any ideas as to why this may be the case?  I need to use the extended network of the Hub of sky wifi is very low when the TV is.

  Here is the configuration...

  Router-> Airport Extreme-> Airport Express-> TV + Surround Sound

  (Airport extreme is the bridge mode value and the expansion of the wifi network Express).

  Thank you

  Jeremy

  TV: Samsung UE40H6400

  Soundbar: Samsung HW-K650

  Rear speakers on your TV: Samsung R1 2

  I'm not familiar with Samsung wireless speakers, but let me see if I can help. What is the brand and model of your router provided by Sky? You have configured to provide a Wi - Fi network? Is the Wi - Fi network, provided by the extreme and extended by the Express, a second wireless network with a different SSID or using the same SSID as provided by the router from the sky?

• Send the datagram via private WiFi network problem

  I'm confused with the sending of datagrams through the private wifi network!

  There are four examples of url to send the datagram in the sample RIMJUDPClient.java

  UDP://10.1.0.122:5029;19780/rim.NET.GPRS
  UDP://127.0.0.1:5029;19780/rim.NET.GPRS: use the Local testing this string
  UDP: / / < public IP >: < Port UDP >; 19780/proxy: use this String with AT & T Service GPRS
  UDP: / / < public IP >: < Port>;19780/internet3.voicestream.com UDP: use this string with T - Mobile GPRS Service

  However, I would like to send the datagram through the private wifi network and find an example url for non-GPRS network in "Development Guide:

  For example, the address for a connection of CDMA network would be udp://121.0.0.0:2332; 6343.

  So I tried the url ' udp://iport1; port2 /; interface = wifi", but it does not work in the 8320 (v4.2.2.180) device. the send() throw Exception content 'null '.

  My udp support private wifi network connection.

  My url is correct? Can you show me an example url used to create the connection for the private wifi network?

  Appreciate for any help!

  UI = wifi parameter has been added in version 4.5.0 of BlackBerry API set.  You will need to upgrade your BlackBerry device software in order to to use.  Please see the web site of your operator for an upgrade.

• My first computer user when I created the second user... Help! :(

  Hello, I really ned a quick response... :/

  So I created a second user yestarday, so I had them 2, after some time I switched user and then turned my pc of. Later when I went to loggn in my user to fir trees, I couldn't, because it was just possible to loggn into second account... it does not show that there first user, I had...

  The second user that I created was a Director? would it be posible that my first user is deleted somehow? :((

  I don't know what's heppening, but I really need the other user, because its so much important things for me! :(

  But I still do not see him... It's like gone...:(quand j'ai voulu loggin àle premier utilisateur, il ne m'a donné choix trop choisi premier utilisateur ou en second lieu, c'est juste me demanda pasword à deuxième utilisateur j'ai créé:(()

  Please help me, I need a lot of treatment

  If I read your post correctly, I guess the account you were using was the original administrator account which can be renamed.  When you create a 2nd account, it is normal that Windows hide the original at this point administrator account.  Rename the user administrator does not rename the profile, so you will probably find your files in 'Administrator' in the folder c:\documents and settings\.  This may be the reason why your account is hidden.

  If this is the case, to log in to your original account, when you get to the opening of session "Welcome" with only the 2nd account, press Ctrl-Alt-Del twice.  This should bring up a login screen 'classic '.  Try typing your user name and password in the boxes and see if you can connect.

  If you can connect and want two accounts to display, you need to create another profile and transfer your files/data in this additional profile and leave the original hidden administrator account.  To do this, pretend that your hidden account profile is corrupt and follow one of the following procedures:

  "How to recover damaged Windows XP user profile"
    <>http://support.Microsoft.com/kb/555473 >

  "How to copy data from a corrupted to a new profile in Windows XP user profile"
    <>http://support.Microsoft.com/kb/811151 >

  HTH,
  JW

• Bug trying to create the link with the Cyrillic characters in URL

  I'm transforming words in my text on the links, but with Cyrillic characters in their URL (such as https://en.wiktionary.org/wiki/ хорошо). The problem is that, depending on how create the link, the page refuses to accept the URL.

  It's my preferred method (which accepts not the Pages):

  1. Write or select the text to be transformed into link;
  2. Press cmd + k;
  3. Paste the URL (https://en.wiktionary.org/wiki/ хорошо) in the field;
  4. Hit enter or click out;
  5. When I check the link, it is www.apple.com.

  The strange is that other methods work very well.

  1 against nature (accepts Pages):

  1. Delete my word;
  2. In its place, paste the URL (https://en.wiktionary.org/wiki/ хорошо);
  3. Hit the space bar (a link is created automatically with the correct URL);
  4. Edit the link that is created and change its text;
  5. When I check the link, he kept correct.

  2 against nature (accepts Pages):

  1. Write or select the text to be transformed into link;
  2. Press cmd + k;
  3. Find a way to build a version with my URL (https://en.wiktionary.org/wiki/%D1%85%D0%BE%D1%80%D0%BE%D1%88%D0%BE) escape sequence;
  4. Paste the URL with escape sequence in link field;
  5. Hit enter or click out;
  6. When I check the link, ironically, is хорошо https://en.wiktionary.org/wiki/.

  To stretch more:

  1. Editing a link created successfully (with any success methods above);
  2. Changed its URL (from хорошо https://en.wiktionary.org/wiki/ to https://en.wiktionary.org/wiki/ плохо)
  3. Hit enter or click out;
  4. When I check the link, it's still хорошо https://en.wiktionary.org/wiki/;
  5. Finally edited and changed its URL still once, now remove the Cyrillic (https://en.wiktionary.org/wiki);
  6. Press enter, click out and he finally accepted the URL.

  Pages seems to be denying the creation of links with the URL that contains Cyrillic characters (only?), but exclusively through his little creation of link popup. I think it's a simple problem, but I'm sure it's very annoying.

  Everyone knows the same?

  Cyrillic characters in the range of table encoding UTF-8 code points u + 0400 - u + 04 FF are represented by two bytes. These people must be encoded as a percentage (read the two paragraphs of the current standard of article), as the Pages v5.6.2 will convert automatically URI to this encoding for you in the link Inspector. It will simply ignore what it considers incorrect URI links, they are Cyrillic, or even English.

  Use what is easier for you, and that Pages v5.6.2 accepts.

• re4000w and setting the channels with wrt54gl

  Hello

  Could someone help me I have a wrt54gl and want to use re 4000w, is it possible, that I can't see ay area set the channel on re4000w.

  Set to auto dhcp, or this unit only works with wrt54gl in static mode?

  Tony

  RE4000 Getway should be 192.168.2.1

• What does that say "automation server can't create the object" with undefined is null or not an object

  I get these pop ups on an application I have to access it through a company VPN

  Hello charliedoodle,

  Given that the application tries to reach a Web site through the VPN to your business, you should check with your integrated personnel.
  They may have a problem on the server, or may have set a new strategy group. We would not be able to help with this issue.

  However, you can watch the following article which addresses the error message you receive.
  Click the number of the KB article to revise article.
  KB Article ID: 323885 -error message in Visual Studio: "Automation server cannot create the object.

  I hope this helps.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Create the user with privileges only data entry.

  Hello guys,.

  A very basic question. I created the request of APEX, well obviously the user with whom I created this application has developer access, now I want to create a user who is able to see the developed application, I tried to find the user options, but could not.  Someone can help me to find the option, I need to follow, so that the newly created user is only able to enter data into forms and run reports and should not be able to make changes in the application developed.

  Concerning

  Faisal Niazi says:

  A very basic question. I created the request of APEX, well obviously the user with whom I created this application has developer access, now I want to create a user who is able to see the developed application, I tried to find the user options, but could not.  Someone can help me to find the option, I need to follow, so that the newly created user is only able to enter data into forms and run reports and should not be able to make changes in the application developed.

  Create 'end users' by selecting No for the user is an administrator of the workspace and the user is a developer account privilege options create new user accounts. These users connect to the APEX Application Builder. It can be given direct access to a request by specifying the ID of the application or alias to the URL:

  apex.oracle.com/pls/apex/f?p=

  or

  apex.oracle.com/pls/apex/f?p=

  Using an alias for the application is recommended.

  To restrict user access to pages, components and specific applications, create authorisation schemes and the apply to the application level.

• Create the cluster with existing Virtual Machines

  This will seem like an easy question, but I have 3 5.0 ESXi hosts managed by vCenter. We recently purchased a SAN and I would like to set up a cluster, can I do it with running on the existing VMS host computers and then to migrate in the SAN that I have create the cluster?

  If the hosts and the BIOS settings are the same there should not be a problem with placing them in a cluster. Displacement of that virtual machine to the San can be made as soon as the hosts are connected to him, it is not the members of classes.

  André

• create the database with Oracle Client link

  Hello together,

  on my machine Windows 7 with Oracle Client installed 12.0.1.0, I'm trying to create a database link to a database server, which runs on Oracle Standard Edition1 11.2.0.2.

  When I connect to sqlplus on the client with "sqlplus/nolog" and type the command:

  SQL > create SID of the database link

  connect to the user identified by passwd

  using "tnsnames.ora connection."

  I have a SP2-0640: not connected. OK, it is clear, because I use sqlplus with option/nolog. But client-side normally I have no database, where I can connect. So I think, there is no user, or?

  The database to which I want to connect is located in tnsnames.ora.

  Generally: Is it possible to use the Oracle Client to create a database link? Maybe there's another way to do this?

  A big thank you and best regards,

  David

  You don't seem to understand the concept of a database link.

  A database link connects two databases. Not a client and a database.

  You need to link up in a data source to a target database.

  The only thing you need is a client of sqlplus in sqlplus client, you need to connect to the source database.

  If you can't connect to the source database, you must present the statement to someone.

  Sybrand Bakker

  Senior Oracle DBA