Similar Questions

• Dell PowerEdge T320 PERC H710P Upgrade

  Dear support, I have a Dell PowerEdge T320 server that was purchased with a software RAID controller in S100.  I just bought a PERC H710P controller and hoped to help on the installation.  Do I need anything else to install the card as a set of cables?  I have a 8 x 3.5 "hot swappable backplane already installed with a pair of cables SAS that connect to the motherboard.  What else do I need to do this work?  I'm also not sure where the PERC H710P controller must be installed?  I can't find pictures or drawings on the Internet.

  Thank you

  Joe

  Jpmigliozzi,

  You should also order the cable (part # DJXF7) as well. This is the cable that connects the 710 in the bottom of the basket 8 x 3.5. Look at the picture below and let me know if those are the cables you already have.

  

  Let me know.

• Internal tape drive SAS Dell PowerEdge T320/T420

  Hello

  I am installing a SAS LTO4 tape drive in a Dell PowerEdge T320 Tower Server.  I have the tape drive and the controller/HBA H310 SAS for the connection to the drive but I can't find the right cable for the H310 training. #

  I'll use P/N: 606JD, which is listed on the TBU for T610/T710 cable but don't know if it's the cable for this unit.

  Any help would be massively appreciated.

  Thank you

  Hello.

  Need you Cable Mini SAS to part number: J7KJW.  P/N: 606JD cable is not compatible with T320/T420

• PowerEdge SC1425 - upgrade Memoria RAM [GRO]

  Buongiorno.

  On our Dell PowerEdge SC1425 - serial number 9TRNQ1J - abbiamo di memoria RAM add need.

  Secondo features found in manuale (SDRAM DDR - 2 400 ECC - 72-bit, PC-3200 Unbuffered, SDRAM, DIMM, clocked at 400 MHz) it nostro fornitore, ha dato della memoria compatibile con queste features, tried my abbiamo anche, e sebbene works memoria di diversi tipi, questa non viene riconosciuta dal Server che in indica "modules no memory detected" con accensione seers of diagnosis : verde-giallo-giallo-giallo.

  Vorremmo sapere is esiste some della memoria, oltre a particular characteristic which indicate in manuale oppure is esiste some settaggio inversions del bios del server per poter fare Upgrade ram of della.

  Grazie.

  Salve,

  He problema e che he Server non riconosce PC2-5300, Halter retrocompatibilil knew altre macchine, lato Server selezione e molto più ristretta.

  Di seguito di ufficiale Dell compatibility list:

  F6928	DIMM, 256, 400 M, 32 X 72, 8, 240, 1RX8	400 MHz, 1RX8 256 MB DIMM 32 X 72, 8K, 240,
  XP764	DIMM, 1 G, 400M, 128 X 72, 8, 240, 1RX4	1 GB DIMM, 400 MHz, 128 X 72, 8K, 240, 1RX4
  4D554	DIMM, 256, 400 M, 32 X 72, 8, 240, ROMB	400 MHz, 256 MB 32 X 72, 8K, 240, ROMB DIMM
  X 1564	DIMM, 4G, 400 M, 512 X 72, 8, 240, 2RX4	4GB DIMM, 400 MHz, 512 X 72, 8K, 240, 2RX4
  G6036	DIMM, 2G, 400 M, 256 X 72, 8, 240, 1RX4	2 GB DIMM, 400 MHz, 256 X 72, 8K, 240, 1RX4
  H2084	DIMM, 512, 400 M, 32 X 72, 8, 240, 2RX8	DIMM 512 MB, 400 MHz, 32 X 72, 8K, 240, 2RX8
  JT055	DIMM, 2G, 400 M, 256 X 72, 8, 240, 2RX4	2 GB DIMM, 400 MHz, 256 X 72, 8K, 240, 2RX4
  G6035	DIMM, 1 G, 400M, 128 X 72, 8, 240, 2RX8	1 GB DIMM, 400 MHz, 128 X 72, 8K, 240, 2RX8
  F6929	DIMM, 2G, 400 M, 256 X 72, 8, 240, 2RX4	2 GB DIMM, 400 MHz, 256 X 72, 8K, 240, 2RX4
  D6599	DIMM, 1 G, 400M, 128 X 72, 8, 240, 1RX4	1 GB DIMM, 400 MHz, 128 X 72, 8K, 240, 1RX4
  C6956	DIMM, 512, 400 M, 64 X 72, 8, 240, 1RX4	DIMM 512 MB, 400 MHz, 64 X 72, 8K, 240, 1RX4

• Dell Poweredge T 310 - memory problems

  Good afternoon.

  I have a Dell PowerEdge T310 running Windows 2008 R2 server.

  It came with sticks of memory without buffer 2 x 2 GB 1333 Mhz. (4 GB Total)

  I've added sticks of memory 2 x 2 GB 1333 Mhz unbuffered and it worked very well send me a 8 GB of total memory.

  Last week I bought an another memory sticks without buffer 2 x 4 G 1333 Mhz, to make it to the 16GB total, using all six (6) available slots on the motherboard Intel XEON based.

  Now, the server does not start and gives me an error of memory on the front screen.

  If I take 2 sticks, using only the new 2 x 4 GB and 2 x 2GB memory stick the server will start without any problems.

  I'm looking for answers 'why' this will not work with 4 x 2 GB and 2 x 4 GB sticks using all 6 (six) places available.

  I am eager as much memory as possible and use all 6 locations.

  I can buy 6 sticks of memory "recorded", but if that no longer works I hesitate to purchase.

  Any help would be greatly appreciated.

  (Navigation on Amazon, I find a kit of registered models they say will work Dual Rank and having the possibility to use all 6 locations):

  24GB (6 x 4 GB) KIT for Dell PowerEdge series M610 (ECC Registered T310 (registered ECC). DIMM DDR3 ECC registered PC3-10600 1333 MHz Dual Rank memory RAM. Real brand A-Tech.

  ReneWold,

  Question you see specific Udimm. Like the T310 only supports up to four access unique. As seen on page 109. If you were to go to access fourth instead, then would you be able to use the 3 DIMMs per channel, allowing you all DIMM 6.

  Let me know if this helps answer your questions.

• upgrade brain Server DELL PowerEdge T320 Service TAG: 50JJF62

  Salve,

  MI servono due per questa macchina brain.

  Q.TA 2 x 2 TB near Line SAS 3Gbps

  oppure

  Q.TA 2 x 2 TB, near line SAS 6Gbps

  Saluti

  Riccardo

  Buongiorno, di upgrade development cars required by it business service.

  Questo forum if occupied della risoluzione di guasti per sistemi fuori co.

  Todas

• Dell PowerEdge T320 does not start

  Hello

  Customers told Dell T320 server that no longer starts. He said that he tired to update firmware iDrac, but after restart server could not start. Server initializes the memory and starts initialization of iDrac, stays there for a few minutes, giving massage iDRAC initialization failed and restarts again and again. never of boots. I tried to remove all components PCIe and USB, no luck.  Please let me know how I can fix this problem

  Lapinas

  Now I get error swc0700 IDrac and life cycle control disabled.

  This error is caused by multiple restarts that lead to errors of IPMI. Update the firmware of the iDRAC.

  Reposition the controller and the ends of the cables connected to the controller. This device is installed on the 4 PCIe slot? Re-seat all PCIe devices and restart. Response to my e-mail with DSET report.

• Reference DELL e R510 upgraded memoria RAM [MS]

  Buongiorno,

  need di fare one set at level dei miei Server DELL R510.

  Sul sito dell trovo:

  SOLUZIONE 1

  Modulo di memoria sostitutivo certificato Dell 16 GB by some sistemi Dell - 2Rx4 RDIMMS LV for a 1600 MHz ECC

  Number di parte Winery

  SNP20D6FC / 16G

  Number di parte Dell

  A6994465
  a 165 euro

  e

  SOLUZIONE 2

  Modulo di memoria sostitutivo certificato Dell 16 GB by some Dell - 2Rx4 RDIMMS sistemi a LV DDR3 - 1333 MHz (require Westmere-EX (Intel Xeon E7) CPU-PowerEdge R810, R910, M910)

  Number di parte Winery

  SNPMGY5TC / 16G

  Number di parte Dell

  A6996789

  a 190 euro

  Qual'e the migliore Soluzione per me? Come posso verificare is both sound much compatibility?

   

  Supporto Dell

  Buongiorno,

  the memoirs da lei indicates sono perfettamente con compatibility it sistema reported

  OK, my che differenze, sono tra una e l'altra? Quella che costa di piu e piu veloce ha diverse prestazioni? o no no vale la Peña

  Supporto Dell

  , unica cosa, the memoirs currently has bordo 2 x 2 GB vanno estratte prima di installare the nuove.

  perch, so is diverse di memoirs? Ed incpmpatibili tr aloro?

  If a se, posso, having a disposizione della stessa series, installarle server other server knew an altro, Così da a rrivar a 8 GB knew quello?

  Supporto Dell

  
  Speaking saluti

  Manual

  e possibile avere un offerta da referred to dell by the scope ed sommergibili delle memoirs?

• PowerEdge T320 compatible memory

  Hello

  I had a server T320 with single processor, I has 4 GB of RAM, I want to expand the memory at least 16 GB.

  Is there a list of compatible memory modules that can be used

  Here is an example

  HMT31GR7BFR4C-PB Hynix

  Samsung M393B1G70QH0-YK0

  HP 605313-071 Micron

  If I can get the memory of 510 Poweredge servers can also allow here.

  Thank you

  BHU

  Outside the group that you listed, the only one that looks like it might be compatible would be the Hynix. More glancing DIMMS for the R510, there is a bar shared memory, but it's a 2GB. I don't see any other compatible crossing those listed. Thus, it can be up to error on those you have.

  Also you can mix brands of memory, as the population of DIMMs can be different as long as the population for each socket mode and rules.

  • If dimms of different speeds are mixed, all channels across all CPUs operated at the common frequency of the slowest dimm.
  • That a single dimm type is allowed per system: UDIMM or RDIMMS. They cannot be mixed.
  • The first slot dimm in each channel is color-coded with white release tabs to facilitate their identification.
  • Rank savings and mirroring
  • DIMMs must be installed in each channel from the furthest Dimm to CPU. DIMMs must be installed with County rank largest to smallest. For example, if DR is mixed with modules DIMM SR, the DRs should be in the lowest Dimm then SR DIMM slots.

  Here are some numbers if necessary part.

  D65JJ - 4 GB 1600 MHz 2RX8

  CPX35 - 8 GB 1600 MHz 2RX4 low voltage

• T320 upgrade memory

  Last year, I had a T320 with the installation of 4 x 8 GB 1600 single rank memory in ECC. I now seeks a maximum of memory in the system and would like to buy 2 x 16GB sticks and use the remaining locations. I know that other housing are disabled when set up as ECC. The server running VMWare 5.5, it will have problems if I swap the memory of ECC memory optimized?

  Also, after he traded it looks like I need to pass the memory slots 2, 3, 5, 6 to 1, 2, 3, 4?

  If all that is Ok, then when I've add 16 GB dual rank sticks should they be put in slots 1 and 2 or somewhere else?

  Thanks for the help.

  Hello

  matthewkilgore

  The server running VMWare 5.5, it will have problems if I swap the memory of ECC memory optimized?

  You shouldn't have any problems switching to Advanced ECC.

  matthewkilgore

  Also, after he traded it looks like I need to pass the memory slots 2, 3, 5, 6 to 1, 2, 3, 4?

  If all that is Ok, then when I've add 16 GB dual rank sticks should they be put in slots 1 and 2 or somewhere else?

  The T320 has two banks of tri-channel (1-3 and 4-6). You shouldn't mix memory in a bank. In the generation previous servers that we did not have the type of population that you intend, but 12th-generation and later supports flexible memory configurations. This means that we have very few restrictions population. You can put the memory almost anywhere you want. This does not mean that the entire population will work or be supported. It simply means that we do not block the non-optimal memory configurations as much as we did in the past. The population of best for what you are considering would be:

  16 GB - 1.4
  8 GB - 5.6 2.3

  Thank you

• I have to shutdown PowerEdge T320 to add more disks?

  Hello

  We have a Dell PowerEdge T320 with following Perc

  ID	0
  Name	Adapter PERC H310
  State	Loan
  Firmware version	20.12.0 - 0004
  Driver version	6.801.05.00

  Currently, the server has two drives of 1 TB on a RAID 1 virtual disk. I want to add more than 4 drives (2 TB) and create a RAID 5 with 3 disks and leave one as a spare drive. So my questions are:

  1. do I need to disable the server in order to add new readers? -the server has access area Bay front for Perc connections, which are the SATA drives.

  2. what would be the appropriate steps to set up the RAID. Can I make using Dell Open manage?

  3. do you know if the 2 TB drive, I want to use as a hot spare works also for the 1 TB RAID 1 drives?

  Thanks in advance.

  1. you should NOT turn off to add or replace the hot-swappable drives. Leave it on.

  2. Yes, use OpenManage... Select Reconfigure in the drop-down list of tasks available for RAID 1.

  3. Yes, the reader may be bigger, but not smaller. All larger than the other Member disks space will be wasted space. Then, you'll go from a 1 to a 4 TB RAID 5 RAID 1. Half of all your drives of 2 TB will be wasted.

  Another thing, you need to know is that if Windows is ALREADY installed with UEFI enabled (as opposed to the BIOS), then you can not use more than 2 TB. Windows cannot use a greater than 2 TB drive unless it's TPG, and Windows cannot start a GPT disk except if installed on UEFI system activated. Conversion to GPT is destructive, so it cannot be changed without reinstalling.

  My advice would be to set up your 4x2TB in a 4 TB RAID 6 disks - RAID 6 is a better use of a 'rescue' as a backup pending. RAID 10 would also be acceptable.

• Change a failing drive - RAID Dell Poweredge H310 - RAID 1

  Hi guys,.

  Thank you for everything that support you in these forums. I'm new here.

  We have a Dell PowerEdge T320 server on my new place of work. It is Dell Poweredge H310 RAID controller on it. It is configured in RAID-1, with 2 discs.

  Now my question is: in the event that one of the drives breaks down:

  1 - I should insert the new drive into the slot where the failed disk has been inserted, or in the following location?

  2 - will be the new drive automatically "copied" with the healthy disk data or it will need some work?

  I read the manual and chapter 'Replacement year Online physical disk', says the following, but I don't know the answer to these questions:

  1. in the management of virtual disks window, select Virtual Disk # and press the arrow key down until the physical disks is highlighted.

  2. press arrow right key to expand the list of physical disks that are members of the virtual disk.

  3. press the down arrow and select the desired physical disk that you want to replace. Press to view the list of operations permitted on the disc.

  4. Select Replace and then start.

  5. tap on the down arrow to select a replacement disk and then press the SPACEBAR to select the disk.

  6. click OK to start the replacement.

  Any advice would be appreciated.

  Kind regards.

  Videoclocknet,

  You must remove the failed disk and replace it with another similar drive on the same niche. When you choose the following location, be sure to follow the steps in the virtual disk management screen (VD) as you have indicated.

  The failed drive will be replaced and the replacement drive will be one on the following location. Either way is perfectly fine. You can then monitor status of the VD and the reconstruction process using OpenManage Server Administrator (OMSA).

  2 disks configured in RAID 1 act as a reflection of the other. Failure of 1 drive ensures that the same data are available on the other. When you replace the failed disk, the rebuilding process begins, and the same data gets automatically copied.

  Please let me know if you have any other questions.

• Dell PowerEdge R710 memory upgrade 16 GB (4x4Go) for 72GO with more than 64 GB (8x8Go)

  Hi all

  My Dell PowerEdge R710 is seen 16 GB (4x4Go) now and would like to add 64 GB (8x8Go), it will be total 72GB. Please help me add memory into the slot on the right. Can I do the following as below

  A1/B1 > 8 GB

  A2/B2 > 8 GB

  A3/B3 > 8 GB

  A4/B4 > 8 GB

  A5/B5 > 4 GB

  A6/B6 > 4 GB

  Thanks Robert, I already bought 64 GB (8x8Go) and would like to add to my current server which is running 16 GB (4x4Go). So, please show me how.

  Thank you

  Binh Kien

• Upgrade memory PowerEdge 2900 III

  All 3 poweredge 2900 people use the same type of ram? I have a dell poweredge 2900 III and am looking at an upgrade of ram which is listed as compatible with the first generation, the PC2-5300F. I was wondering if this does not work for my 2900 gen 3.

  Also, can someone shed some light on what the maximum capacity of RAM for the 2900 III.

  Thank you guys!

  Hello.

  The PC2-5300F which is a fully Buffered DIMM is which was delivered with all the 9th Gen Dell servers and should be compatible across all revisions of 2900. What is the size of the memory you are looking for? In my view, that the maximum RAM capacity on the 2900 III server is 48 GB.

  I hope this answers you questions.

• Update memory Dell Poweredge R510

  Hello.

  There are two Dell Poweredge R510 servers with the following configuration:

  CPU: Intel Xeon X 5675 (3.06 GHz, 6 C, 12 Mb cache)

  Additional CPU: Intel Xeon X 5675 (3.06 GHz, 6 C, 12 Mb cache)

  64 GB of RAM by 2CPU (LV double rank of 8 x 8 GB RDIMMS) 1333 MHz

  We want to upgrade servers with 128 GB of RAM.

  What is the most appropriate way to do it?

  Can I order 8 modules with 16 GB of RAM and replace?

  Thanks in advance for your help.

  Enzorik,

  You can order and use the 16 GB DIMMs in the R510. You can see the directives of the population by proc on page 117 of the guide, located here. Before the memory upgrade, however, you must be certain that you have the server to update BIOS, Drac, lifecycle controllerand Raid Controller. This is to ensure that the server remains stable.

  Let me know if that answers your question.