Difference between NAT vs vs Bridged, Host-only for the setting of my network card?

Similar Questions

• VPN Cisco ASA 5540 L2L - one-way traffic only for the pair to a network

  Hello

  I'm a little confused as to which is the problem. This is the premise for the problem I have face.

  One of our big clients has a Cisco ASA5540 (8.2 (2)) failover (active / standby). Early last year, we have configured a VPN from Lan to Lan to a 3rd party site (a device of control point on their end). He worked until early this week when suddenly the connection problems.

  Only 1 of the 3 networks the / guests can access a remote network on the other side. 2 others have suddenly stopped working. We do not know of any change on our side and the remote end also insists that their end configurations are correct (and what information they sent me it seems to be correct)

  So essentially the encryption field is configured as follows:

  access-list line 1 permit extended ip 10.238.57.21 host 10.82.0.202 (hitcnt = 2)
  access-list line 2 extended permit ip 10.207.0.0 255.255.0.0 10.82.0.200 255.255.255.252 (hitcnt = 198)
  access-list line 3 extended permit ip 10.231.191.0 255.255.255.0 10.82.0.200 255.255.255.252 (hitcnt = 173)

  Free NAT has been configured as follows (names modified interfaces):

  NAT (interface1) 0-list of access to the INTERIOR-VPN-SHEEP

  the INTERIOR-VPN-SHEEP line 1 permit access list extended ip 10.231.191.0 255.255.255.0 10.82.0.200 255.255.255.252
  permit for Access-list SHEEP-VPN-INSIDE line lengthened 2 ip host 10.238.57.21 10.82.0.202

  NAT (interface2) 0-list of access VPN-SHEEP

  VPN-SHEEP line 1 permit access list extended ip 10.207.0.0 255.255.0.0 10.82.0.200 255.255.255.252

  After the problem started only 10.207.0.0/16 network connections worked for the site remote 10.82.0.200/30. All other connections do not work.

  There has been no change made on our side and on the side remote also insists there has been no change. I also checked how long the ASAs have been upward and how long the same device has been active in the failover. Both have been at the same time (about a year)

  The main problem is that users of the 10.231.191.0/24 cant access remote network network. However, the remote user can initiate and implement the VPN on their side but usually get any return traffic. Ive also checked that the routes are configured correctly in the routers in core for the return of their connections traffic should go back to the firewall.

  Also used of "packet - trace" event raising the VPN tunnel (even if it passes the phases VPN). For my understanding "packet - trace" alone with the IP source and destination addresses must activate the VPN connection (even if it generates no traffic to the current tunnel).

  This is printing to the following command: "packet - trace entry interface1 tcp 10.231.191.100 1025 10.82.0.203 80.

  Phase: 1
  Type: ACCESS-LIST
  Subtype:
  Result: ALLOW
  Config:
  Implicit rule
  Additional information:
  MAC access list

  Phase: 2
  Type: FLOW-SEARCH
  Subtype:
  Result: ALLOW
  Config:
  Additional information:
  Not found no corresponding stream, creating a new stream

  Phase: 3
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  in 10.82.0.200 255.255.255.252 outside

  Phase: 4
  Type: ACCESS-LIST
  Subtype: Journal
  Result: ALLOW
  Config:
  Access-group interface interface1
  access-list extended allow ip 10.231.191.0 255.255.255.0 10.82.0.200 255.255.255.252
  Additional information:

  Phase: 5
  Type: IP-OPTIONS
  Subtype:
  Result: ALLOW
  Config:
  Additional information:

  Phase: 6
  Type: INSPECT
  Subtype: np - inspect
  Result: ALLOW
  Config:
  class-map inspection_default
  match default-inspection-traffic
  Policy-map global_policy
  class inspection_default
  inspect the http
  global service-policy global_policy
  Additional information:

  Phase: 7
  Type: FOVER
  Subtype: Eve-updated
  Result: ALLOW
  Config:
  Additional information:

  Phase: 8
  Type: NAT-FREE
  Subtype:
  Result: ALLOW
  Config:
  NAT-control
  is the intellectual property inside 10.231.191.0 255.255.255.0 outside 10.82.0.200 255.255.255.252
  Exempt from NAT
  translate_hits = 32, untranslate_hits = 35251
  Additional information:

  -Phase 9 is a static nat of the problem to another network interface. Don't know why his watch to print.

  Phase: 9
  Type: NAT
  Subtype: host-limits
  Result: ALLOW
  Config:
  static (interface1, interface3) 10.231.0.0 10.231.0.0 255.255.0.0 subnet mask
  NAT-control
  is the intellectual property inside 10.231.0.0 255.255.0.0 interface3 all
  static translation at 10.231.0.0
  translate_hits = 153954, untranslate_hits = 88
  Additional information:

  -Phase 10 seems to be the default NAT for the local network configuration when traffic is to the Internet

  Phase: 10
  Type: NAT
  Subtype:
  Result: ALLOW
  Config:
  NAT (interface1) 5 10.231.191.0 255.255.255.0
  NAT-control
  is the intellectual property inside 10.231.191.0 255.255.255.0 outside of any
  dynamic translation of hen 5 (y.y.y.y)
  translate_hits = 3048900, untranslate_hits = 77195
  Additional information:

  Phase: 11
  Type: VPN
  Subtype: encrypt
  Result: ALLOW
  Config:
  Additional information:

  Phase: 12
  Type: VPN
  Subtype: ipsec-tunnel-flow
  Result: ALLOW
  Config:
  Additional information:

  Phase: 13
  Type: IP-OPTIONS
  Subtype:
  Result: ALLOW
  Config:
  Additional information:

  Phase: 14
  Type: CREATING STREAMS
  Subtype:
  Result: ALLOW
  Config:
  Additional information:
  New workflow created with the 1047981896 id, package sent to the next module

  Result:
  input interface: interface1
  entry status: to the top
  entry-line-status: to the top
  output interface: outside
  the status of the output: to the top
  output-line-status: to the top
  Action: allow

  So, basically, the connection should properly go to connect VPN L2L but yet is not. I tried to generate customer traffic of base (with the source IP address of the client network and I see the connection on the firewall, but yet there is absolutely no encapsulated packets when I check "crypto ipsec to show his" regarding this connection VPN L2L.) Its almost as if the firewall only transfers the packets on the external interface instead of encapsulating for VPN?

  And as I said, at the same time the remote end can activate the connection between these 2 networks very well, but just won't get any traffic back to their echo ICMP messages.

  access-list extended allow ip 10.231.191.0 255.255.255.0 10.82.0.200 255.255.255.252
  local ident (addr, mask, prot, port): (10.231.191.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (10.82.0.200/255.255.255.252/0/0)
  current_peer: y.y.y.y

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 131, #pkts decrypt: 131, #pkts check: 131
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0

  If it was just a routing problem it would be a simple thing to fix, but it is not because I can see the connection I have to confirm it by the router base on the firewall, but they don't just get passed on to the VPN connection.

  Could this happen due to a bug in the Software ASA? Would this be something with Checkpoint VPN device? (I have absolutely no experience with devices of control point)

  If there is any essential information that I can give, please ask.

  -Jouni

  Jouni,

  8.2.4.1 is the minimum - 8.2.4 had some issues (including TCP proxy).

  If this does not resolve the problem - I suggest open TAC box to get to the bottom of this ;-)

  Marcin

• What is the difference between win 7 pro DSP OEI DVD and the OEM or normal Full pack?

  1. What is the difference between win 7 pro DSP OEI DVD and the pack OEM or normal Full we learned normally?
  2. does DSP OEI DVD comes with CD of instalation?

  These versions are for small integrators (DSP = 'partners in enforcement service'), which usually contain a single Windows (1pk = 32-bit or 64-bit, not both as in commercial versions) and an OEM preinstallation kit to preconfigure Windows and/or integrate additional tools (OEI = 'Installation of Original equipment' or 'Integration organizational environment'). They have the same limitations that versions OEM = license is tied to the computer where the operating system has been installed initially and not transferable in case of death of the machine. "192GO should be enough for everyone." (of the miniseries "Next generation jokes")

• Tree node in data recovery for the 1st node only for the 3 data blocks?

  Hello alllll
  
  I have 3 BLOCKS of DATA master / detail-detail; GL_TYPES - < GL_ACCOUNTS - < GL_COMPANIES
  
  The Rel attribute between 1 and 2 is
  

  GL_ACCOUNTS. TYPE_ID = GL_TYPES. TYPE_ID

  is between 2 & 3 ADR
  

  GL_COMPANIES. ACCOUNT_ID = GL_ACCOUNTS. Account_id

  I have also a Tree is recovering the data in blocks of data, the following code, used in the trigger WHEN-TREE-NŒUD-SELECTED and it works fine, but not for all nodes;
  the selected node displays the data for the first node only. Assets to say but if I chose to any other node it returns no data?
  
  you could any boady pls explain to me why what is happening?
  
  The following code is:
  -----------------------------

  DECLARE
                      
          htree ITEM;
          NODE_VALUE VARCHAR2(100);
  
   BEGIN
  
   IF :SYSTEM.TRIGGER_NODE_SELECTED = 'TRUE' THEN  
        
  -- Find the tree itself.
  
   htree := FIND_ITEM ('BL_TREE.IT_TREE');
   
  
    NODE_VALUE := FTREE.GET_TREE_NODE_PROPERTY( htree, :SYSTEM.TRIGGER_NODE ,  Ftree.NODE_VALUE );
    
  
    GO_BLOCK ('GL_ACCOUNTS'); 
      
     set_block_property('GL_ACCOUNTS', DEFAULT_WHERE, 'GL_ACCOUNTS.ACCOUNT_ID = '  || 
     ftree.get_tree_node_property('BL_TREE.IT_TREE', :SYSTEM.TRIGGER_NODE, FTREE.NODE_VALUE));
  
   EXECUTE_QUERY;
   
   END IF;
        
   END;
  
  
   

  Kind regards
  
  Abdetu...

  I would say there is nothing in relation to tree now. Because the tree is to give the appropriate value for the setting of the block where clause. Check the relationship and that the cursor goes to the block expected where the data must be retrieved. Like you said tree account id that the tree is from the correct values.

  -Clément

• Will that be HP motherboard compatible with RAM only for the card mother amd?

  Hello

  I have Compaq 510 with motherboard HP

  I want to upgrade from 2 GB to 4 GB

  I only compatible DDR2 Ram only for the AMD motherboard

  my laptop that will run RAM?

  I don't want to lose my money to buy an another RAM

  thankss...

  Sorry for my bad English

  You must ask to HP/Compaq.

• I just bought the 14 items and I don't see the download button. only for the operating system of the ILO. Help, please.

  I just bought the 14 items and I don't see the download button. only for the operating system of the ILO. Help, please.

  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If he continues to not try to use a different browser.

  Download and Installation Help-

  https://helpx.Adobe.com/download-install.html

  PES 10, 11, 12, 13, 14 - https://helpx.adobe.com/photoshop-elements/kb/photoshop-elements-downloads.html

  PE 10, 11, 12, 13, 14 - https://helpx.adobe.com/premiere-elements/kb/premiere-elements-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  Photoshop/Premiere Elements 14: http://prodesigntools.com/photoshop-elements-14-direct-download-links-premiere.html

• How to make all the fields on one page read only (for the recipient) without having to make each field read-only?

  How to make all the fields on one page read only (for the recipient) without having to make each field read-only?

  Hello Jmbtexas4,

  By default, you will need to individually click on the fields of the form and check the 'read only' and save it. From now on, it is not possible to select all together and make the changes.

  -Usman

• Hi, I installed Windows 10 on my II Surface Pro today and I lost my ADobe Acrobat program, installed, but it took a key no. from a previous version. My no. is only for the update to Acrobat XI. Thank you

  Hi, I installed Windows 10 on my II Surface Pro today and I lost my ADobe Acrobat program, installed, but it took a key no. from a previous version. My no. is only for the update to Acrobat XI. Thank you

  Hey Samy,

  Please read: error: "this serial number is not for a product calling it" | CS6 cs5, CS5.5,

  Hope that helps!

  Kind regards

  Sheena

• Are the five sites of free creative cloud only for the test?

  Are the five sites of free creative cloud only for the test?

  Hello

  No, you can add your own domain name to these sites and use them like any other normal site. Let me know if you have any specific doubt, and I will try to answer,

• What is the difference between pls_integer index and index of directory for a collection?

  Hi all

  I have a bit of difficulty understanding the difference between pls_integer and directory when you declare a collection...

  Is not so much pls_integer than the supposed to be the same in 10g and 11g?

  My problem is that I've declared a collection in a procedure with directory and by record type, it takes 10 seconds to process. (IE TYPE test_table IS the TABLE OF test % rowtype directory INDEX ;))

  However, the same procedure with the declared collection with index of pls_integer, take only 1 second to process. (IE TYPE test_table IS the TABLE OF test % rowtype INDEX BY PLS_INTEGER ;))

  Any help would be welcome.

  Thank you.

  MichaelR wrote:

  I don't understand when say you not to use DML in a LOOP and use sql only. Can you please give me an example?

  I usually of code like this:

  1. I'm looped slider
  2. Update table_name
  3. the value of col1 = i.rec1
  4. where col2 = i.rec2;
  5. end loop;

  This approach is incorrect.

  All SQL is parsed and executed as SQL cursors. There is no such thing as use SQL or cursor.

  A cursor is a "compiled SQL program. Source SQL that has been analyzed in a cursor executable code. When you retrieve the cursor, you push the button the cursor or program execution. It finds a row and return lines. He's on a break. You get the rows returned, these processes and then click the button run the cursor using fetch. Until the cursor/program finds no additional data (or he faces a snapshot too old for example, where it can not rebuild a coherent reading to find the next set of lines).

  A cursor is and has never been a set of cached data in memory that you are recovering from.

  Take a look at your code. You use a slider/program to retrieve data from the database. For each row in the cursor returned, you call another slider/program and pass this line as input data.

  It's slow. Data line moves a cursor to your PL/SQL code, and then again from your PL/SQL code to another cursor.

  A single slider that makes the reading (the SELECTION cursor) part and the part of writing (the slider to UPDATE), requires no PL/SQL to read and write the parts together.

  How to write this unique SQL cursor? You can use:

  UPDATE (SELECT... Of... JOIN THE... WHERE...) SET...

  You can use the MERGE statement. Or maybe just a statement UPDATE simple vanilla.

  What is the problem of a conceptual, performance and scalability point of view, is the approach that you have indicated above. That approach will ALWAYS be slower than just SQL. This approach cannot scale.

  The mantra of performance for Oracle is simple: Maximise SQL . Minimize the PL/SQL.

  Use the SQL language correctly and properly. Do not what SQL is designed to do, in PL/SQL.

• The difference between them and how they are used by the first?

  I'll buy Adobe CS5 Master Collection. I have a job that has Win 7 Ultimate 64-bit. I have a Nvidia CX card that is installed. The Nvidia card came with fast HD. I will also receive a Matrox MXO2 mini for my junction box.

  My Question is what is the difference between - fast HD, elemental Accelerator, technology Max that you can get with the Matrox junction box, and all this will be of use to me or come into conflict with the Mercury playback engine. I don't think I'll buy the Max technology (no not necessary). But I'm confused on the other 3 being redundant or contradictory.

  Can someone please suggest another option for a junction box? Some companies do not support their products if you are using a Dell workstation.

  Any help would be greatly appreciated.

  Thanks in advance for any advice or suggestions.

  Martin

  Post edited by: Mallady1

  RapiHD is the former name of the elemental accelerator. The EA is a PP plugin that uses your graphics card from nVidia (via CUDA, nVidia GPU programming structure) to speed up encoding h.264/AVC output files. The previous link in this thread is wrong, but here is a link to work for the elemental Accelerator. The product is pretty much dead end, so much that it will be not a CS5 version. There is a stand-alone version called lucky, but it requires you to use Adobe products to encode firstly your timeline to an uncompressed AVI file (or any other format), thus defeating the purpose.

  The Mercury playback engine uses CUDA to accelerate the effects, transitions and insight into the chronology PP. It accelerates only marginally encoding, or not at all. There are a lot of threads on this forum discuss the EMT.

  I have a Blackmagic Design card, so I can't tell you anything about the Matrox card and its software.

• Difference between different models (sold in different regions) of the iPhone 7

  I'm traveling to the Japan, and it turns out that my phone broke. So, I plan to buy iPhone 7. But I noticed that there are different models according to the countries or regions. According to Apple customer service, it has to do with different bands of LTE in different regions. But exactly the same bands that WE supported the Japanese model (which is completely separate from all other) / version of the EU with the exception of it's CDMA.  She would work very well after my return to Europe (Germany)? Where can I buy non-CDMA, GSM version for the Japan as well.

  Here is the link showing the differences between the various models of iPhone 7.

  You have a question?

• What is the difference between 3.6.25 and more recently as the version 9.0.1

  I'm not sure to understand the difference between the versions of 3.6 and many 9.0.1 version. I have much more trouble with this new version - actually had to uninstall it because it kept crashing. I understand that there are more bells and whistles, but what is the advantage of the most recent on this old reliable version?

  See:

  • http://www.Mozilla.org/Firefox/features.html

• What is the difference between REFin and PPSin? Can I use the PXI-5652 to synchronize USRPs?

  Hello world!

  I'm working on a project I want to synchronize 8 USRPs (USRP 2920) as receivers. And it seems that PXI-5652 has a connector REF, so I decide to use it as the reference of the USRPs 8 clock. But I don't know how to connect the PPSin, and in fact I'm confused of the difference between the REFin and PPSin.

  Thank you!

  Jay_c salvation,

  In short,.

  REF is the terminal for the device USRP to accept a signal from external reference frequency (10 Mhz).

  PPS is the terminal for the device USRP to accept a signal from external time source base clock (1 pulse per second)

  You can see this whitepaper for a detailed description of MIMO system about 8 * 8.

  Please refer to the section "time and frequency" for information specific to your question.

  http://www.NI.com/white-paper/14311/en/

  I'm not sure whether you can use the specifically 5652 signal generator for your application.

• What are the differences between "PowerState" and "Guest.State" when I run the powercli command Get - VM

  I run the script following powercli: -.

  Get - VM | Export-Csv-path c:\test.csv - NoTypeInformation - UseCulture

  And from there I found 2 properties that describe the State of the virtual machine;

  1 PowerState which can be either; Receiving or PoweredOff

  2 Guest.State, which can be either; running or not

  Can someone so advice on the differences between these two properties? Could I have for example a VM with PowerState = PowerOn, and that his Guest.State = no run?

  PowerState if the State of the virtual machine itself.

  Documentation Centre of vSphere 6.0

  PoweredOff

  Receptor

  Suspeneded

  Everything about .guest is achieved through VMware tools and provide information to the OS itself.

  (VMware tools must be installed and working properly in the operating system to get whatever it is this property)

  Documentation Centre of vSphere 6.0

  Keep

  Reset

  Running

  ShuttingDown

  Standby

  Unknown

  Could I have for example a VM with PowerState = PowerOn, and that his Guest.State = no run?

  Yes.

  For example, if a virtual computer is started and VMware tools have never been installed on it, it will signal exactly that.

  From the vSphere Client, you will get in the summary > General > VMware Tools

  Does not not (not installed)

  You will get more information using the API via PowerCLI.

  . extensiondata.runtime.PowerState #poweredON

  . extensiondata.guest.GuestState #notRunning

  . extensiondata.guest.ToolsStatus #toolsNotInstalled