Driver overran the buffer battery and I it keeps restarting my PC every half hour

Similar Questions

• Equium L10: Problem with the main battery and battery RTC

  Hello

  I have the Toshiba Equium L10 and it is about 14 months old and I have problems with the battery and how much time it takes after a full charge. I also have problems with the RTC battery and an ERROR 0271: check date and time settings message when I turn on the laptop.

  Regarding the battery, I can fully charge it upward in about 3 hours, but when I start to use it, apparently in the last few hours around one and a half or so and then it needs to be recharged. I can have down for about 40 minutes and then turn it off and come back later or in a day or two. How long should I expect from a fully charged battery?

  About the batttery RTC, it really becomes a pain and I only started to get the message of the ERROR 0271 start-up, in recent weeks. I can charge the battery pack and then leave for a few days, but when I turn it on, I get the message ERROR 0271 on the date and time incorrect. Surely after a full charge, the RTC battery should last longer than a few days?

  The manual says that if the RTC battery is exhausted or becomes weak, you must charge the battery of the CCF for 24 hours, in a different part of this manual indicates between 24 and 48 hours, but how can load you for long when the sections concerning the charging battery pack status after charging the battery you unplug the power adapter because leaving connected will shorten the life expectancy of the Battery Pack. So, how we can charge the battery of the CCF for 24 to 48 hours if we shouldn't leave the AC adapter plugged in once the battery is charged - which is nearly three hours. Suggestions about these problems would be appreciated.

  Besides we all know that it is easy to change the CMOS/RTC battery in your desktop base unit, but is it easy to change in a Toshiba Equium L10?

  Concerning

  Brave0

  Hi Brave0,

  The normal recommendation for the CMOS (RTC) battery is to leave the laptop connected to the power supply at least 12 hours when the main battery is fully charged. The charging circuit is going to hijack the current to the load automatically RTC battery and no current will be forwarded to your main battery.

  Recommendation do not leave the power adapter is plugged in the main battery is fully charged is really only applicable to older laptops that used no batteries Li - ion and therefore they had to be completely discharged before recharging to avoid any effect 'memory' of the battery.

  With modern Li-ion batteries, it is quite safe to leave the battery when fully charged and still power the laptop from the AC adapter. The charging circuit will pass all the battery charge if it is fully charged.

  Kind regards

• External hard drive not a letter from reader: I already installed device driver for the same thing and it's showing in disk management.

  External hard drive not a letter from reader: I already installed device driver for the same thing and it's showing in disk management. But when I checked in system information, it is also displayed device but sectors and the tracs where showing the value 0.

  Hello Sharan,

  These links may help:

  http://TechNet.Microsoft.com/en-us/library/cc750198.aspx

  http://TechNet.Microsoft.com/en-us/library/cc977219.aspx

• "Sorry, your computer has encountered an error and needs to restart. We are only collecting the error information, and then we'll restart for you. "windows 8

  Hi so I recently bought a new computer and out of no where he worked in some really annoying errors. This has happened three times, I can't understand a reason yet, AFAIK, it occurs randomly. A few times I start up my computer and it starts just the windows icon, the loading circle is not displayed. If I let it run it will remain still frozen. After a few reboots, he says still 'preparation auto repair' is still frozen. This has happened 3 times.

  The first time I have not jumped into the recovery CD, no problem, used a system restore, it was all good.

  The second time, she actually had a cause, our power went out and my pc was used, then maybe he could have ruined a circuit. So I put the CD, it wouldn't recognize it and if he did, he would freeze just and nothing to do. I tried F8, F12 and F1: he didn't even recognize these keys or react at least based on them.
  After a few restarts I miraculously managed to do recognize the CD and this time I made a cooling system.
  This lead me to think it might be some of my files/programs, but I'm still working on acquiring them all back after the update so I think it is unlikely that. 3rd time: yet once, it happened when I turned it on after a normal closed. It would not recognize the cd or the keys. After maybe 15 attempts, but rather oddly, everything was OK? I also noticed that my Tablet Wacom Intuos 5 is connected it will not start, but if I unplug it, it starts very well. (Driver error?)

  All this is fine and dandy, I can deal with it, but not until recently that error in the title stood. I noticed, that it normally occurs when the computer is in "sleep" or the monitor turns off because it is inactive. If I move the mouse to bring on the monitor, it is just a bright blue solid then the following message: "sorry, your computer has encountered an error and needs to restart. We are only collecting the error information, and then we'll restart for you"appears and it stops. Whenever this happens, it starts up just fine, it is just annoying it encounters this error whenever I use it. I tried to do system recoveries, but it did not help. I can just do a reset or refreshment, but again once I do not want this effort and to lose files if the error is still going to happen. I'm not sure if this is a hardware error, heating, maybe? But I'm not all that experience in these things. As I said, this computer is fairly new, maybe 2 months, then maybe I could just put its warranty policy to use. But if you can think of anyway to help, it would be great thanks!

  My specs are:
  Avatar
  CPU: AMD FX Processor with Six cores (tm)-6100 3.30 GHz
  GPU: Geforce GT 640

  16.0 GB
  operating system 64-bit, x 64 processor
  Windows 8.1

  Hi Kaelie,

  This issue seems to be with the material. As you mentioned that your computer is under warranty. It would be better if you contact the manufacturer of your computer for help on this issue.

  Just reply to us if you are having problems with Windows in the future. We will be happy to help you.

• I bought a new camera with a disc of Adobe Photoshop Lightroom 5.  I have a pc with windows 8.1 windows.  I downloaded and deleted about 5 times.  It says installed properly, but whenever I hit the icon the pc hangs and I have to restart AID

  I bought a new camera with a disc of Adobe Photoshop Lightroom 5.  I have a pc with windows 8.1 windows.  I downloaded and deleted about 5 times.  It says installed properly, but whenever I hit the icon the pc hangs and I have to restart AID

  Uninstall your lr 5.

  install lr 5.7.1 and use your serial number to activate.

  Available downloadable Setup files:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
  • Lightroom: 5.7.1. 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5.5, 5 | 1
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Why continue those class Scheduler start and stop every half hour approximately

  Why continue those class Scheduler start and stop every half hour approximately. I am fortunate to have a sound event for the event program open and this event is triggered by Multimedia Class Scheduler, it seems, every half hour.
  Is this normal?
  Can I disable it?

  James

  Hello

  Service Multimedia Class Scheduler (MMCSS) allows multimedia applications to ensure that time-sensitive processing receives priority access to the CPU resources. This service allows multimedia applications to use CPU as possible without denying CPU for low-priority applications as well.

  This service is required only for the fact that the Windows Audio service lists this as a dependency. Without the Windows Audio service, no audio signal will play on the system. This service is started when the system starts, but shortly after (~ 8 minutes), it stops.

  This is a Notification which will start with all programs that use Windows Audio. For an example if you open Windows Media Player, then multimedia class scheduler also starts because it uses the windows audio.

• What is the speed of the hard drive of the 2015 2 and 3 to merge disks partition?

  I was looking through the Apple site and was wondering about the speed of the drive in the iMac in car merger. On their site it says that the 1 TB Fusion drive has 24 GB of Flash memory, and 2 models to and 3 to have 128 GB of Flash storage. But it does not say what the speed of the hard drive partition, which is what I want to know. It is 5400 RPM, or even 10000 rpm or 7200 RPM? I don't know, but I want to know. If anyone here knows the answer to this question, I would appreciate a response. Thank you.

  I have seen it reported that the Fusion drives are all 7 200 RPM.

• Format HARD drive, delete the recovery partition and recover with disc

  Hello

  I have a laptop Satellite C660D-17F and want to format my HDD, remove the recovery partition and recover the preinstalled Windows 7 and other software. I don't want to keep my own data, which are all stored already, I just want to be sure I can safely restore preinstalled stuff. I have a few questions that I need help to clear up before I go ahead.

  Am I right in thinking the dvd recovery disc I made when I got to my laptop has all the software and drivers that I need on this subject, the same that would have the recovery partition? If I do another room to spare in now just to be sure only will they have the out-of-box default stuff: OS, software and drivers on any of my data?

  I found [this post | http://www.mytoshiba.com.au/support/items/faq/71] which explains the recovery process. If I select "Erase the hard drive" (so I can wipe my hard drive and delete the recovery partition too) what happens after that? It will restore the OS and the software for the backup of dvd drive? Will the process after that recreate a recovery partition (which I don't)?

  Added SIDENOTE:
  I actually prefer to be able to choose what programs preinstalled settle after that I have format, but I'm guessing that probably isn't possible and will settle for install everything and remove what I'm after. Or is there a way?

  Sorry, I know that was a long post, but I want to be sure of what will happen BEFORE I'll and spoil things! :) If you got this far, thanks for reading. :)

  Hello

  I will try to offer help. ;)
  > Am I right in thinking the dvd recovery disc I made when I got to my laptop has all the software and drivers that I need on this subject, the same that would have the recovery partition?
  Yes. Saved on recovery discs recovery image contains the operating system, all necessary drivers, specific Toshiba and utility tools and some additional software.
  > If I do another room to spare in now just to be sure only will they have the out-of-box default stuff: OS, software and drivers on any of my data?
  Preinstalled Toshiba Recovery creator make recovery disc that includes the recovery image only. It has nothing to do with your personal data.
  > I found this post that explains the process of recovery. If I select "Erase the hard drive" (so I can wipe my hard drive and delete the recovery partition too) what happens after that?
  After that, you should use recovery disks created for the recovery image installation.
  > Will the process after that recreate a recovery partition (which I don't)?
  When you use the recovery disc for your laptop recovery image installation will have factory settings which include the recovery saved on the HARD disk image. To be honest I do not understand why you do not want to have this recovery image on the HARD drive. This allows the installation of recovery using recovery of HARD drive option. But of course you can delete it later for more free space on your HARD drive. Installation image that you can always use created for recovery discs-recovery DVDs.
  > I'd really rather be able to choose what programs preinstalled settle after that I have format, but I'm guessing that probably isn't possible and will settle for install everything and remove what I don't want after
  Fix.

  Also - check http://aps2.toshiba-tro.de/kb0/HTD1303440001R02.htm

  Good luck and if you have any other questions feel free.

• PASTE THE BUFFER DUPLICATION AND ATTRIBUTES OF THE PEN OF A PHOTO TO ANOTHER

  I am trying to create the effect of Parallax through a catalog of the same photos. Is it possible for me to paste the clone stamping I did on one photo and paste attributes to the next and so on? Thank you

  If you used the Clone Stamp tool in a new empty layer where you sampled all the layers of cloning in the empty layer. You can drag the layer cloned in your next documents. You can continue clone stamping in the layer to chip away and drag this layer in the following document and so on...

• Several times (not all the time) when I disconnect my lap top and then plug it back, the computer crashes and I have to restart manually.

  I called Dell a few weeks ago.  They had me remove the battery, press the power button 15 X and then restart.  They did a scan of material and said that everything was going well.  I ran once again virus scan software, and there is no virus.  I deleted all temporary files.  They said that perhaps, it might be a problem of software somewhere but wanted a ridiculous just to check amount only.  Do I have other options as to how can I fix?  This is a NEW computer that I just received in August!

  Hello

  What antivirus/antispyware/security products do you have on the machine? Be one you ALREADY had on this
  machine, including those you have uninstalled (they leave leftovers behind which can cause strange problems).

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ---------------------------------------------------------------------------------------

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes without doing anything - then right click on the task - bar
  The task manager - take a look at stored by - Services - process - it is a quick reference (if you have
  a small box in the lower-left - show for all users can check only).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG and then display a list of the people here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out what are the files, registry keys and other objects processes have opened, the dll
  they loaded and much more. This exceptionally effective utility will show you even owned by each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to startup automatically when your system boots and you
  opening of session. Autoruns also shows you the full list of registry and file locations where applications can configure auto-
  start the settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  WhatsInStartUP - free - this utility displays the list of all applications that are loaded automatically when Windows
  starts. For each request, the following information is displayed: Startup Type (registry/Startup folder).
  The command - line String, product name, file Version, company name, location in the registry or the file system,
  and much more. It allows you to easily disable or remove unwanted programs that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window Watcher says it all, reporting of any window created by all running programs, if the window is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 the love of the updated drivers that can drastically affect the performance so I would update the main
  drivers.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Try to reconnect the file history and then try to restart it, it says has been disconnected.

  Original title: Ihave even question rereconnecting windows player 8

  I tried to re connect my history of file player from what I've read, will reconnect the file history.  you try to restart it, it says has been disconnected. How can I reconnect it them. has the red x on the icon

  Hi Larry,

  1. What is the full error message that you receive?

  2. you try to connect an external USB driver for backup?

  You may receive this error message if the external hard drive is not properly detected.

  You can consult the section "Reconnect your drive" article and check:

  What happens if something is wrong in the history of the files?

  For more information, see the articles:

  Restore files or folders by using the history file

  Set up a drive to history file

  Protect the user with history of files files

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• My laptop hard drive had to be replaced, and now I can restart all programs except Acrobat 9 Pro CS4?

  My drive hard laptop died and had to be replaced recently. I was able to restart all programs except for Acrobat 9 Pro CS4 disc? Can anyone tell if there is a different process to restart Acrobat Pro 9, as it is strange because there is no problems with other components of CS4 software?

  By restarting, I assume you mean reinstall. For CS, Acrobat installation is a little strange compared to the rest of the CS package and requires other parts of the CS to activate or certain aspects of these. One of the messages at the beginning of this forum responds to this problem (or used to). Otherwise, I suggest you check in the CS forum.

• Links in the Facebook crash and Safari pages keep reloading / crashing even with iOS 9.3.2

  Ive got ios 9.3.2 and links in Facebook keep crashing again. And every time I try to navigate in safari or chrome pages keep reloading. Sometimes only couple of times, but other times it charging until the phone freezes and puts an end to all applications and sent it to me to the home screen. Shurting, sometimes even to the bottom of the Web page. There are some days where was at its worst, but it stopped after the phone automatically just reset (like holding home and power at the same time button). But it doesn't work when I do it myself. At the moment it is slightly backward. Especially with the Facebook links crash. But my safari page was actually not to recharge for some reason any while I was typing this question on my iPhone. It is very annoying because I can't navigate on my phone. Actually, it gets to the point where any other webpage just keep reloading until phone crashes.

  I'm using an iPhone 6 +.

  I do not know how to solve and I thaught it was a 9.3 iOS problem. I use 9.3.2

  It was not a problem in the 9.3, there is a problem with your phone. That's why 9.3.2 has not set. As a first step, remove the Facebook application, reboot your phone in now the HOME and SLEEP buttons simultaneously until the Apple logo appears, and reinstall the FaceBook application by downloading it with the App Store application on the phone.

  For Safari, open Safari, tap the HOME button, wait a second, double - press the HOME button and sliding upward on the Safari screen image. Then go to settings/Safari and tap clear history and data from the Web site. Reboot again.

  If the problem persists after these steps, restore iOS through iTunes and set the phone like New. Do not restore the backup, because the problem is most likely in the data to be backed up.

• I have blown my motherboard on an old computer and hooked up my old hard drive to the new computer and want to transfer my favorites on the new drive but cannot find where they are located on the old drive - any help?

  My motherboard went bad on my old computer, but the hard drive was OK. I bought a new computer and plugged my old hard drive to it via a usb adapter. I would like to import or copy my favorites from the old hard drive to my new, but I can't find where they are. I was unable to determine the search for articles on the web. Be advised that my old hard drive is basically nothing more than a place of storage for files at this point. My old operating system is windows XP, and my new system is Windows Home Premium.

  https://support.Mozilla.com/en-us/KB/recovering+important+data+from+an+old+profile

  Your old profile is located here in Win XP and W2K:
  
  drive: \Documents and Settings\username Windows login\Application Data\Mozilla\Firefox\Profiles\profile_name

• Why is it hard drive see the photos, films and music even after I deleted all

  Hello

  I recently deleted all my photos, movies and music on my Mac to save on hard drive.

  However, despite the removal of all my hard drive is showing:

  3.2 GB movies

  1.3 GB Audio

  Photos of 4.3 GB

  I searched these files and the results come back with nothing but my hard drive is still showing that this space is taken to the top.

  Does anyone have any ideas or ideas?

  Thank you

  Andrew

  Hard drive space and 'other ':

  https://support.Apple.com/en-GB/HT202867

  Also, try to rebuild the Spotlight index: https://support.apple.com/en-us/HT201716