dv5-2130us turns off instead of mode 'sleep'

Similar Questions

• HDD turns off after the mode 'sleep'?

  I would like to know if the hard drive would turn out or not after the mode 'sleep'.

  Does anyone have any suggestions?

  Thanks in advance for your suggestions :>

  The computer do not hibernate unless it stops the disc after writing the hibernation file.

  Mode for similarly low-power stop discs 1

• Dragon Naturally Speaking has stopped working, how to turn off Windows compatibility mode?

  How can I turn off Windows compatibility mode

  I use Dragon Naturally Speaking (DNS) and all of a sudden it will not open. The info, after trying MANY proposed options, says "turn off Windows compatibility mode.

  Hello

  1. don't you make changes before the show?

  Try the following steps to disable the compatibility mode.
  a. Locate the launch of Dragon NaturallySpeaking file, right-click on it and click Properties.
  b. click on the Compatibility tab.
  c. in compatibility mode, uncheck the box "run this program in compatibility mode for".
  d. click ok to apply the changes.
  e. check if the problem persists.

  If the problem persists, then contact the program vendor support team:see Dragon NaturallySpeaking support

• Computer won't turn on after the mode 'sleep'

  My computer acted funny lately when it goes into mode 'sleep', and I have to reboot it until I can do something new. I know I'm not the only one having this problem, I've read the other posts on this problem. Anyway, my keyboard has a sleep button that I brush occasionally, that causes all this to happen. However, I brushed it today, and instead to go just in a coma, the computer entered into mode 'sleep' (the light was orange, noise died down), then woke up to the top in a way where the fan on, but the light went off. I've forced to close and then turned back on. Now when I turn it on, the light and fan both going on, but the monitor remains off, and none of the lights on the keyboard lights up. Is there a simple solution to this, or it will need repairs?

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Perform the steps from the link below.

  The problems of wake the computer from sleep mode

  Warning: Be careful when you change the BIOS settings. The BIOS interface is designed for advanced users, and it is possible to change a setting that can prevent your computer from starting properly. BIOS update should be made only if necessary (to solve a compatibility problem, for example). It can be a complicated process, and if an error occurs, your computer could be rendered inoperative. Be sure to observe the instructions of the manufacturer.

  Reference link provided below for more information:

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/BIOS-frequently-asked-questions

  Hope this information helps.

• Yoga s1 - keyboard/trackpad turn off in tablet-mode/tent

  Hello

  I have the version of edu 10 school windows to install on my thinkpad yoga s1 and I following driver problems.

  no rotation of the screen

  not auto brightness

  keyboard / trackpad doesn't turn off when screen undergoes a rotation, more mixture windows does not work because he does not notice that the screen is different.

  are there drivers or fixes to this problem. I installed all lenovo drivers I found on the Web site and the software update, and he said no problems. also, the Device Manager shows no points mark.

  can someone help me, I need this laptop for my studies. I thought I'd make the wise choice to do a fresh install of windows to leave out any confilicts but this is long over.

  Kind regards

  NeatFreak

  Mod edit: System model added to the subject line to improve visibility / clarity

  Thanks for that.
  Unfortunately it has not worked for me, but I understood what the problem was. It was because I installed the "N" of windows 10 EDU verion and leading to some problems with the sensors and the touch screen. So if I install extension multimedia Windows 10 out of the microsoft page, everything worked from the unpacking so no need for pilots to sensor.

  Thanks for the help =)

• When we turn the or after mode 'sleep' my motherboard will load but then nothing else... White screen. If I reboot and select Safe mode it loads. If I reboot in safe mode then everything works. Windows loads, everything works.

  When I turn on my PC or after mode 'sleep' my motherboard will load but then nothing else... White screen.  If I reboot and select Safe mode it loads. If I reboot in safe mode then everything works. Windows loads, everything works.

  I have this pc for 3 years.  My system was full of unused and unwanted programs, so I rebooted to Vista, deletted all my old files that Vista had moved into the "old." This is when I started having this disorder.

  (I made this process more yet to see if it would help with no luck)

  My first thoughts were video driver... downloaded the new drivers 3 times.  scanned all the other drivers for updates ect. nothing seems to help...

  Anyone have any ideas?

  Thank you

  Dave

  I have

  I was able to download these files.  Rthl64.sys point - one component of your network cable in pictures device driver memory.  Interestingly, the dates of the 2006 pilot (Rtlh64.sys my Sep 26 07:20:23 2006 (45190CF7)), so it's most likely your problem.  Follow these steps:

  -Download a new copy of the software/drivers on the website of Realtek here: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=7&PFid=10&Level=3&Conn=2

  -Uninstall the current software/drivers on your system

  -Install the newly downloaded drivers

  -Monitor for more BSOD

  Here is a summary of the BSOD:

  BSOD BUGCHECK SUMMARY

  By: 6002.18267.amd64fre.vistasp2_gdr.100608 - 0458
  The debugging session: 16:23:07.947 Sun 31 Oct 2010 (UTC - 05:00)
  System Uptime: 0 days 13:18:38.380
  WARNING: Unable to verify timestamp for Rtlh64.sys
  ERROR: Module load completed but symbols can be loaded for Rtlh64.sys
  Probably caused by: Rtlh64.sys
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  BUGCHECK_STR: 0X9F
  Nom_processus: System
  Code 0000009F error checking
  Fffffa80 00000000 00000003' arguments'03de3a30 fffffa80 '05bf1050 fffffa80' 072dc010
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  By: 6002.18267.amd64fre.vistasp2_gdr.100608 - 0458
  The debugging session: 22:49:49.007 sat 30 Oct 2010 (UTC - 05:00)
  System Uptime: 0 days 5:12:31.440
  WARNING: Unable to verify timestamp for Rtlh64.sys
  ERROR: Module load completed but symbols can be loaded for Rtlh64.sys
  Probably caused by: Rtlh64.sys
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  BUGCHECK_STR: 0X9F
  Nom_processus: System
  Code 0000009F error checking
  Fffffa80 00000000 00000003' arguments'03def060 fffffa80 '05bdf050 fffffa80' 04aeb2d0
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  By: 6001.18000.amd64fre.longhorn_rtm.080118 - 1840
  The debugging session: 21:48:58.144 Wed Oct 27 2010 (UTC - 05:00)
  System Uptime: 0 days 9:49:32.487
  WARNING: Unable to verify timestamp for Rtlh64.sys
  ERROR: Module load completed but symbols can be loaded for Rtlh64.sys
  Probably caused by: Rtlh64.sys
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  BUGCHECK_STR: 0X9F
  Nom_processus: System
  Code 0000009F error checking
  Fffffa80 00000000 00000003' arguments'03a1ca30 fffffa80 '05-99050 fffffa80' 039c8c60
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``

  -John ( http://www.carrona.org/index.html )

• Windows 8: laptop turns off instead of going to sleep!

  Hello

  Earlier, everything was going well but over the past 10-15 days, I am facing a problem.
  PROBLEM: Whenever I have press the power button / stop or try to put the pc to sleep, it shuts down the screen but hard drive and other things stay active... and after 2-3 minutes it shuts down my laptop completely. So, I have to start my laptop instead of awakening it.

  
  I have configured my laptop for the following measures:
  1 power button
  2. close cover
  3 icon pressed sleep I have start menu
  4 sleep after 20 minutes of inactivity.

  For all of the above-mentioned actions, pc should go to sleep which does not occur. Please suggest me something.

  Hello

  Keep the computer in a clean boot state, and check. If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem. Continue with the remaining steps to pin-point on the third party service. After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  How to perform a clean boot for a problem in Windows Vista, Windows 7 or Windows 8.

  http://support.Microsoft.com/kb/929135

  Note: please go through the section: How to reset the computer to start as usual after a clean boot troubleshooting section of Kb to start the computer to a normal startup after you fix the problem.

  I hope this helps.

• Turning off on its own sleep time IdeaPad N586 wireless card

  This past weekend here when I left my sit computer without using it, he falls asleep on his own as it is supposed to, but when I put my computer from sleep and reconnect, I know that my wireless card is cut and takes like 30 seconds - 1 minute before to activate it again, I did check the fn + f5 and it showed as wireless card being the even if the wireless network connection showed It is not connected, how do I fix this and recently, I make sure that the wireless connection off automatically to save energy

  Follow this thread here: http://www.sevenforums.com/network-sharing/318973-wifi-sleep.html

• How to turn sound when switching mode sleep?

  Hello

  I got my 13 edge two days ago and have now installed all updates and upgrade the BIOS (how can this amount of updates it will take a new PC? Not surprised a lot of people have problems with their computers...)

  But I can't find out how to make the boring 'BING' when the computer goes into sleep mode. Looked in system sounds and the Control Panel, but I can't. Ether in power options...

  It's embarrassing during the day, but if she wakes up on LAN alert during the night I want it to be QUIET.

  Everyone knows?

  See you soon,.

  johfo

  Power Manager (Advanced mode)-> global settings-> power management options to

  Uncheck "beep when power state changes.

• How can I turn off the mobile mode.

  I have a 10 nexus, which, with a 10 "screen, isn't really a mobile device. Unfortunately, Firefox is indicative of the web pages that it is. Given this information, some web pages redirect to a short page. Turn on "site office request" does not work since I'm no longer on the site I want and this button is not persistent. So the question: How can I enable notification of mobility?

  Hello

  Please try to change the user agent.

  To change the User Agent string, just enter about: config as an address in the address bar of FireFox, where you normally enter a URL (link). I recommend you keep the original value, you can get when you enter about: in the address bar.

  Now press the right button of the mouse for the contextual menu and select 'Chain' of the menu entry 'new '. Enter the preference name "general.useragent.override", without the quotes. Then enter the new value of User Agent: "Mozilla/5.0 (Windows NT 6.1;". Win64; x 64; RV:25.0) Gecko/20100101 Firefox/25.0 "(sans guillemets)."

  I hope this helps!

• How can I turn off battery saving mode? If that's what it is...

  The other day, my computer laptop has become a kind of battery saving mode after I restarted, where I couldn't customize my background and toolbar, and my internet passwords and things disappeared. I can't fix it, and my computer is plugged... It has a taskbar of bright blue and I can't boot up normally with my saved settings. Thank you.

  Hello

  1. What is the brand and model of the laptop?

  2. where have you changed the settings from?

  Method 1: Run the troubleshooter

  See the following site:

  http://windows.microsoft.com/en-IN/windows7/Open-the-Power-troubleshooter.

  Method 2: Restore the default settings in power options

  (a) click Start, Control Panel, system, and security and then Power Options

  (b) according to the plan that you want to change, click on change plan settings

  (c) select restore default settings for this plan.

  I also suggest you please contact the manufacturer of the laptop computer for more help on the issue.

• turn off /on archivelog mode

  Hello
  
  can anyone provide steps to Activate and Deactivate archivelog mode in the RAC nonRAC environments
  
  Thank you

  No cars

  (1) close immeidate
  (2) startup mount
  (3) alter database archivelog / alter database noarchivelog
  (4) modify the database open

  RAC

  (1) alter system set cluster_database = false scope = spfile

  (2) immediate stop

  (3) the COMMENCEMENT of the proceeding from the same node in Mount

  srvctl start database d-i o prod1 mount prod

  (4) alter database archivelog / alter database noarchivelog

  (5) alter system set cluster_database = true scope = spfile

  (6) stop immediately

  (7) start the database

  srvctl start database-d prod

• Satellite A660-18 - powers off after waking from sleep mode

  My powers of Satellite A660-18 wide for 2-3 seconds after waking from sleep. I upgraded the memory from 4 GB to 8 GB, using the site of Crucial, so I know it is compatible. BIOS is updated to 2.00.

  Don't know what to do, how can I fix without turning off completely from mode "sleep"?

  Hey Buddy,

  > I upgraded the memory from 4 GB to 8 GB
  And have you had the problem before you upgrade memory too or as memory upgrade?

• How to close the mode 'sleep'

  How can I turn off keeps it mode sleep stops every five minutes

  Start button > in the search box, type power options > press the Enter key > column to the left, click on change when the computer sleeps > click the point, and then select the time. You can set 1 minute forever > click on save changes when done

• Computer goes into mode 'sleep', even if the power settings has no mode standby enabled

  * Original title: Windows 7 mode 'sleep'

  Hello, I bought a gaming PC just after Christmas with windows 7 (because I don't like 10) and lately I noticed something wrong with her every 10 twinks than the monitor turns off or on mode 'sleep' this isn't a huge problem, but it is extremely boring all my power options have "sleep" mode on and I looked for a solution for centuries and I can't find 1. can someone help me please?

  It dose not do in mode 'sleep' now, I think it's a program called advanced care system do. Thank you for helping us you helped me a lot