Error-200524 occurred at .vi:2 DAQmx Write (analog 1-d NChan DBL 1Samp)

Similar Questions

• Error-200022 occurred at DAQmx start Task.vi

  Hello

  I have peripheral cDAQ and 3 modules that nor-9234 connected.

  My program (see attachment) works correctly with only 2 modules, but does not work with 3 modules.

  With 3 modules I have this error: "error-200022 occurred at Task.vi DAQmx Start.»   "Possible reasons: resource requested by this task has already been reserved by another task."

  To solve this problem, please help me

  Thank you

  Now I understant the error. This is correct (see below)

  

• Why do I get error 200524 for the generating function 2 code example?

  I get the following error message:

  Error-200524 occurred at the generating function 2 channel_lv86.vi

  Possible reasons:

  Scripture cannot be performed because the number of data channels does not match number of channels in the task.

  When writing, provide data for all channels in the task. You can also change the task so that it contains the same number of channels as the written data.

  Number of channels of task: 1
  Number of data channels : 2

  Task name: _unnamedTask

  When I downloaded and ran the 2 channel here code: https://decibel.ni.com/content/docs/DOC-3545

  I have a card pci-e DAQ 6259 and a block BNC-2110

  Why I get this error?

  When I open the VI I selected ' Dev1/ao"under physical channels. I tried all the other options (a0 - a3) which gave the same error message.

  If you have 2 channels in your data (as indicated in the error message), then you must choose 2 channels in your task control (the error message says that you have selected only 1.)

  You saw in the example how they were able to identify the 2 channels of analog output?

• Get error-200088 DAQmx reading (Analog DBL 1Chan 1Samp) .vi < add >...

  Hello

  I am using examples of labview and Labview 2011, I use the a sample.vi acq for the value of the voltage reading.

  but the thing is that I get the error of block then read this DAQmx Read (Analog DBL 1Chan 1Samp) .vi - 200088 ... And it's not indicate the correct voltage in labview.

  I also connected Multi meter with the analog card reader and multi meter gives the correct value, but it is not possible to achieve with labview.

  Please guide me how can I solve this problem which could be the reason for this.

  Thank you very much.

  
  

• Error-200609 occurred in the DAQmx write: selected buffer too small

  Hello, I write a few VI simple test that I will build finally to call external analogue output VI. I started with a very simple program to produce samples finished using the clock on board with DAQmx Timing.VI. When I run the program, I almost immediately get an error. The error message is below.

  Error-200609 occurred at writing DAQmx (Analog DBL 1Chan 1Samp) .vi:1

  Possible reasons:

  Generation cannot be started because the size of the selected buffer is too small.

  Increase the size of the buffer.

  Contradictory property
  Property: Output.BufSize
  Corresponding value: 1
  Minimum supported value: 2

  Task name: _unnamedTask<1C>

  I used the VI DAQmx before in similar applications and never encountered this error. In addition, I read the link below which DAQmx Timing.VI should automatically generate the buffer. Any ideas what could be the cause?

  Data sheet:

  Windows 7

  LabVIEW 2012

  PCIe-6353 as DAQ card

  Here is a picture of my diagram and the VI is attached.

  Oops. Just realized my very stupid mistake: I forgot to add the VI of task start. I did and it works as expected.

• Error-50103 occurred at DAQmx control

  We strive to take into two signals in LabVIEW through our acquisition of data, and then pass them through two channels of detection of distinct peaks, however, when we try to run the program, we get the following message is displayed:

  Error-50103 occurred at DAQmx control Task.vi:14

  Possible reasons:

  The specified resource is reserved. The operation could not be performed as indicated.

  Task name: _unnamedTask<9>

  I have attached the circuit we use below, any help woud be appreciated.

  Problem solved, use:

  http://digital.NI.com/public.nsf/allkb/485201B647950BF886257537006CEB89#case4

• Error-200431 occurred at .vi DAQmx Create Channel (I-acceleration-accelerometer)

  Hello

  I tried to use DAQmx Create Channel to accelerometer and yet it responds with error (see below). When I use max OR to measure the accelerometer (I-acceleration-accelerometer), there is no error, and I see that acceloremeter works.

  OR PXI-1042 and I use OR-4462 card to measure vibration vith acceloremeter.
  

  Error-200431 occurred at DAQmx Virtual Channel Create

  Possible reasons:

  Physical channel selected does not support the type of measure required by the virtual channel you create.

  Create a channel to a type of measure that is supported by the physical channel, or select a physical channel that supports the type of measure.

  Property: I. MeasType
  Requested value:
  You can select: sound pressure, voltage: Microphone, accelerometer, Position: Eddy Current proximity probe, Force sensor: IEPE, speed sensor: IEPE

  Task name: _unnamedTask<104>

  Hi serdaryilmaz,

  I'm not sure why the accelerometer mode does not work, but it works very well in normal mode - it maybe has to do with the accelerometer, you?  Whatever it is, if it works with the voltage mode, I am happy that we found a way to make it work.  Is this an acceptable work around you?

• Error-50103 occurred at DAQmx start Task.vi:11

  Hello

  I use a nor-6008 to perform a thermal sector and I get the error "error-50103 occurred at DAQmx Start Task.vi:11 '. I have read other forums of discussion and it seems combe because I use the wizard DAQmx who don't properly resolve the resource when finsihed. I've dug further and saw that it is linked to an on-board clock synchronization problems. However, I can understand how to solve this problem.

  I thought that I create a loop that continuously monitors inputs and sometimes to interrogate the memory so I'm not kidding to the top of the clock. It's much harder to do than sounds. Can someone take a look at my code and give me some advice/suggestions to clean the DAQmx assistants.

  Thanks in advance

  Cole

  I finished by dividing my resource between the two input channels using a single assistant DAQ and dividing down the data rate and the number of samples. Works fine now.

  Big pain in the ass well.

• error-50103 occurred at DAQmx control Task.vi:6

  I'm new to LabVIEW. I'm using LabView 8.6 and one NEITHER cDAQ-9172. For practice, I'm doing a program that takes the temperature and pressure readings and graphs.

  I don't have the modules or sensors yet, so I started by simulating a RTD temperature measurement NI9217 and a NI9237 module for the measurement of pressure.

  I created 2 while loops that run in parallel. One with an assistant of data acquisition for the temperature and the other with an assistant of data acquisition for the pressure.

  Highlight run out, when I run the program, the signal is both while loops. The temperature seems to work ok and the data graphic. The pressure, however, only goes in once, and I get the error message: "error-50103 occurred at Task.vi:6 DAQmx control Possible reason (s): the specified resource is reserved." The operation could not be performed as indicated. »

  In addition, the stop button does work on my front. I have to use the button stop in the toolbar.

  Anyone has any advice on what I can do to fix this problem or any suggestions on the best ways to address the issue?

  Thank you.

  Search the forums for error 50103.  That will tell you everything you need to know about this error code.

  For more information on your questions, post your VI so we can see what might be wrong.

• I get an error message "an error has occurred while trying to write to the CONFIG folder. MSI"by updating to adobe reader.

  I have a folder named CONFIG. MSI shows as locked in 'share with '.  I can't seem to change the configuration, that is, to unlock the file.  In addition, 'Properties' shows 22 files in the folder but only 2 files display in Windows Explorer.  When I try to update Adobe Reader, I get an error message that an error occurred during the attempt to write to the CONFIG folder. MSI.  I am the administrator on this PC.  What can I do?

  Original title: locked file, CONFIG. MSI

  Hi Paul Rumbaugh,.

   

  (1) this exactly happens when you try to access the folder?
  (2) what is the error message or error code ?
  (3) have you made changes on the computer?

  Method 1-

  You should check if the problem persists in Safe Mode as well.
  To connect in Safe Mode, you must follow the steps in the article-

  Start the computer in Mode safe

  Note: make sure you connect in Normal Mode after you perform the troubleshooting steps.

  Method 2-

  Perform the steps in the article-

  Disable the anti-virus software

  Enable or disable Windows Firewall

  Note: make sure that you turn on Windows Firewall and re- Activate the antivirus after performing all the troubleshooting steps given the computer can be at risk of infection by the virus.

  Method 3-

  See the steps in the link-

  Error writing to file C:Config.MSI

  Note: you must follow step 7 of article to return the computer to Normal startup after you perform the troubleshooting steps.

  Hope this helps!

• Move to the new computer, get "an error has occurred during playback of files or write files to a disk." The disc

  • I tried to move my catalog and PE6 install to a new computer.  This is on a Dell Windows XP machine, and I moved it to a Toshiba Windows 7 (64-bit) machine.  I always kept my photo on an external hard drive files.  My library is 50 GB, 10,000 files.  Here's what I did.
    • Copied the original PE6 installation file on the Toshiba.  Installed but not activate it.
    • Copied my catalog folder to the location of the Windows 7.
    • Plug the external drive into the Toshiba.  So makes that same letter drive as a front.
    • Fired up to PE6 on Toshiba.  Seemed fine in the Organizer.  Everything seemed to be there, but I didn't try to make any changes at this time there.
    • PE6 disabled on the Dell.  Enabled on the Toshiba.
  • Then I realized that it is not fair.  I can edit the keywords and the stars rating on photos, but not the dates, legends or notes.  I get "an error has occurred during playback of files or write files to a disk." The drive is may be full, or there may be problems with the source media. »
  • Only a fraction of the external drive is in use.
  • I can access the files on the external hard drive with another application (Windows Photo Viewer).
  • I tried the reconnect All missing files.  Somewhat ambiguous, she said "There are no files to reconnect."
  • In the properties in the organizer for each photo are the appropriate file names and paths.  Folder view works fine in the Organizer.
  • I can put new files in the directories of the same external drive, import them into PE6, then change them normally.

  What is the best way to get Organizer connected correctly to my files?  I guess I could import all photos on the new machine, but I guess I'd lose some of my metadata.  So it's out of the question.

  Thank you

  Bill

  Well, the recommended method for moving the catalog is to use organizer of the PSE6 on your old computer to do a full backup on your DHM.  (Which backs up the catalog and media files).  Then, on your new computer, open the Organizer PSE6 and restore from this backup.

  Your method seems logical, but...

  Ken

• DAQmx also write Analog DBL 1Chan 1Samp down of released NI USB-6009 - code error-200077

  I'm trying to get 5V 0V high low output of ao0 to an NI USB-6009 based on a switch in LabVIEW using DAQmx writing Analog DBL 1Chan 1Samp.

  When you use a voltmeter connected to ao0 and analog-ground on NI USB-6009; Im not getting anything.

  I also get code error-200077 for some reason any:

  DAQmx Start Task.vi:4
  Property: AO. Max
  asked the value: 10.0
  Valid values begin with: 0.0
  End with valid values: 5.0

  Channel name: Ao0/Dev1

  The task name: _unnamedTask<28425>

  Set the configuration output terminal to the CSR instead of by default.

  Five maximum value and the minimum value to zero.

  See attachment.

• Error-200524 when you try two analog output voltage signals

  I am train to the output of two signals to analog voltage simultaneously using Labview 8.2.1. One is a waveform to produce sound, and the other is a trigger on another computer (using labview 6.1). I've been doing error-200524 write DAQmx. Here is a screenshot of my VI:

  

  The error message says:

  "Measurements: writing cannot be performed because the number of data channels does not match number of channels in the task."
  When writing, provide data for all channels in the task. You can also change the task so that it contains the same number of channels as the written data. "

  How can I solve this problem? Thank you.

  Show you only a waveform in the block diagram.

  Here is a picture that shows what I told you to in my previous post.

  

  The waveform connected at element 0 of the 'picture to build' will be emitted on channel 0.  The waveform that is connected to the item 1 of the 'picture to build' will be emitted on channel 1.  The instance of 'DAQmx writing' is 'Analog 1 D Wfm NChan NSamp.

  Hope that is more clear!

  d

• Error-50400 occurred to the Invoke method: FIFO. Read in Host.vi

  Hey there,

  We have sensors on an engine which are connected to a Board of Directors OR cRIO 9014 (with a NI9411 6 digital input modul channels) and from there, via the network to a host computer.

  cRIO jury: the jury cRIO collects data from the engine and stores in a buffer, it's because the network is to slow for the size of the data

  Host: bed of the host computer in the network buffer on the map of cRIO, on the host computer, it takes specific portions of the data to create charts of the engine pressure

  Error:

  Error-50400 occurred to the Invoke method: FIFO. Read in Host.vi

  Possible reasons:
  The transfer did not complete in the time-out or the specified number of retries.

  This error occurs in the following scenario:

  -motor is running

  -cRIO is running

  When I press the Start button (boolean 3) in the host.VI to start reading the data of the card AFTER I pressed the button to run the host VI.

  The error will not occur if I pressed the button start (3-Boolean) BEFORE I pressed the button to run the host VI.

  We tried to increase the timeout, but it still does not work, the error occurs!

  We would be really happy if you could look over it and help us in this case! If you need more information or if we need to clarify a specific part, please let us know!

  We have included the VI in the attachment!

  Thanks in advance!

  CHRISSE,

  There are a few things wrong in your application, if I can offer a few suggestions.

  First of all, your loops are not running in parallel.  In fact, they are in while loops with a real constant wired for them. I don't know if this is normal for debugging, or on accident.  I would put the question (read pulling elements Dummies) out of your hand while loop.

  Your second nested while that the loop (that of the poll the number of items and then shooting them) will execute only once and can make only a few samples.  I don't think that that's what you're looking for here, and there are two ways we can go here.  You might question continually until you have 0 items available for x time, then you know that you have no more available samples and you can process all the data, OR you can put your computer through this loop and always just write in the file immediately in the form x samples are drawn.

  In addition, the stop of the main loop condition is ( <= 3)="" therefore,="" it="" will="" run="" once="" and="" then="" stop. ="" maybe="" you="" mean="">= 3?

  In addition, you have "add to the file" disabled on your writing to the worksheet, so whenever you write that you are overwriting the old data.  If you want to write constantly, you will lose data.  This can be cured in this affecting true (requiring a new name for file or programmatically removing the old worksheet each time that you run the vi) OR you can recover all your data in a shift register and only write to the file once you have all your available data.

  The error you see is because you try to close your FPGA reference twice.  Simply close it once.

  After seeing your overview, I think this can be cured by simply reading wiring to get your 1440 X 4 items, but as we have seen, this does not work.  Something happens in your system... that's what I want you do... just run the following... code and let me know how much remaining elements it gives you... Once the number remains (I hope for this, and your engine continue to function), press stop, and all values will be presented on a graph for you.  My broken wires are because I do not have the FPGA VI.

  

• SE "error-88705 occurred to self-test" for PCI-6520 after the electric bike for PC

  Hello

  I use a card PCI-6520 on an industrial PC running Windows Embedded Standard (64 bit).  The card works fine in normal use, but if the PC is power off and back on (instead of closing Windows in the start menu), the map do not communicate to the start-up of the machine.  If I try to run a self-test to the MAX, I get the error "error-88705 occurred to the self-test.  The card remains unusable until I restart the PC in the start menu

  Unfortunately this system will be used headless in an industrial application, so if he ever get turned off, it will be turning off the unit and not through windows or the soft power on the Panel switch front of the PC.  It is important that the machine can start in the application of LabVIEW in power on without any external intervention.

  There is also an NI GigE in the PC card and continues to operate correctly regardless of the way in which the PC is off

  Some of the system features:

  Card mother Intel DH67CL

  Core i7 3770 to 3.4 GHz processor

  8 GB RAM

  64-bit Windows Embedded OS

  NOR-DAQmx v9.3.5 driver

  See you soon,.

  Brett

  I just installed version 9.6 of the DAQmx and which seems to have fixed the problem

  See you soon,.

  Brett