Error on packets on an interface

Similar Questions

• Error message: Teredo Tunneling Pseudo-Interface driver must reinstall

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Original title: Error Message: Teredo Tunneling Pseudo-Interface driver must reinstall .__Not able to find this driver on the Microsoft Web site.

  Hi Tony,.

  ·        When and where exactly you see the error message?

  ·        You did changes to the computer before this problem started?

  You can follow the steps below and try to reinstall the drivers and see if it helps.

  a. Click Start.

  (b) in the search box type Start devmgmt.msc and press to enter.

  c. in the Device Manager, click the action tab, and then click Add legacy hardware.

  d. click next then select install manually in a list, then click Next. In the list select the network adapters.

  e. once everything loaded in the manufacturer column, select Microsoft, and then scroll all the way down in the column for network adapter.

  f. Select turedo tunneling adpter in the list, and then next to the installation.

  Following the steps above should help you to install the drivers.

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error msg is not the interface

  After you download a file from the Internet, I then try to open the folder containing.
  then I get error (Interface unregistered)

  Number of windows.

  Try this

  • http://support.Microsoft.com/kb/870707

• Report Generation Toolkit, production of the 2147417842 error, "The application called an interface that was marshalled for a different thread."

  Hello world

  I have an application that stores data in an Excel worksheet by using the report generation tool.  My VI have worked well in the past using Excel XP, but since I have upgraded to Excel 2007, I get COM errors like this:

  "2147417842 error occurred while the application called an interface that was marshalled for a different thread. in Excel_Insert_Text.vi', this is the exact wording, even with the odd punctuation and capitalization.

  The first occurrence of the error is not determined.  Sometimes, to the record 10 sessions, involving a new .xls file, may occur before this error.  Once this error occurs, I must leave LabVIEW to solve.  If I try to do something with Excel, I still get this error, even if sometimes it comes out different source Excel_Open.VI is another.

  These screw logging worked fine until upgrading to Excel 2007.  I checked and I have been using a very old version of the report generation tool, v1.0.1.  I read the documentation and had a big sigh of relief when I realized that I needed to upgrade to v1.1.2 for Excel 2007 help.  However, even after the upgrade, I still get the same errors.  I'm using LabVIEW 8.0.1 and I also build these screws in an application.   The error occurs in the application built both in the IDE of LabVIEW.  Anyone out there have any idea what I can do to fix this?  I google a bit and discovered it is a COM error, but I can't find any reference to the report generation tool specifically.

  Thank you

  Phil

  I think that suits him!

  Here's what I did: I left privileged execution environment level upper VI as "as the appellant.  I tried the "user interface" configuration, but it seemed to slow down considerably the program.

  Then, I found each sub - VI, calling the report generation tool and define the environment for running favorite "user interface".  All the errors went away, and the program is much happier now.

  Big assumption on what a Christian, thank you!

• ASA5505 inscription on SSL cert error when applied to the interface?

  Created a CSR, gets the certificate files, the downloaded ASA505.   Three certificates in the CA certificates; the one in the certificate of identification.  Everything seems all just wonderful.  "Now use the SSL certs: in trying to associate the certificate with the Interface in the SSL settings section, we get an error"

  [OK] ssl encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  [ERROR] ssl trust-point ASDM_TrustPoint5 outside
  Trustpoint are not registered.  If please register trustpoint and try again.

  The cert will appear in the drop-down selection, why the error?  How do I delete it?

  Hi Stewart Buswell,

  I have seen this problem when starting the CSR request through the CLI by using the configuration of the terminal of registration and then going to the ASDM and adding the identity certificate without using the command crypto ca enroll through the CLI.

  In this case, if you use the CLI/ASDM you can follow this guide:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  And the way to solve this problem will be generation a new CSR on the ASDM using the same key pair and install the certificate on this trustpoint. After you apply the cert to the ssl, you can remove the old one which was not.

  Hope this info helps!

  Note If you help!

  -JP-

• Error during execution of Prod Interface

  Hi all

  We moved our project ODI of Dev to prod. and configured physical Arcitecture from production. Connections tested with success. But during the execution of the interface, we receive some error like below.

  STEP: Drop target about databaselink

  ORA-02024: database link not found

  STEP: Create a database on the target link

  ORA-01031: insufficient Previledge

  My patterns of Datawarehouse meet s/n previledge.

  My source and the target is to have databases Oracle 11.2

  Can someone tell me what could be the problem?

  concerning

  Abdel Aziz

  Hi all

  The question is the question previkledge to create the link target to the source database DB and is committed

  concerning

  Abdel Aziz

• ERROR 2: The class or interface 'Event' could not be loaded.

  Hey, I'm new to the Forum and I have problems with Flash that comes, I can't fix. I have this error that tells me how "the class or interface 'Event' could not be loaded. The error is on the 5th line of code:

  1 stop();

  2

  3 addEventListener (Event.ENTER_FRAME, preLoad);

  4

  5 function preLoad(e:Event):void { }

  6 var bytestoLoad: Number = loaderInfo.bytesTotal;

  7 var numberLoaded:Number = loaderInfo.bytesLoaded;

  8 if(bytestoLoad == numberLoaded) {}

  9 removeEventListener (Event.ENTER_FRAME, preLoad);

  gotoAndStop (2);

  } else {}

  _root.preLoader.preLoaderFill.scaleX = numberLoaded/bytestoLoad;

  _root.preLoader.bytesPercent.text = Math.floor(numberLoaded/bytestoLoad*100) + '% ';

  }

  }

  I know that the code is AS3, but I can not pass by atm AS3 and I need the same code, but for AS2. So, can someone convert this for me? Moreover, it is supposed to be a preloader and I put this on the 1st frame. So I have extensions (.as), just the .fla file.

  Also, I use the newest Flash, Adobe Flash CS6.

  The Flash version has nothing to do with the things works or not.

• Error message - status of the Interface Windows printer has stopped working

  I am able to print just one document for this error message to appear.  It happens every time I try to print.  When I restart the computer, it prints the current document.  The error occurs once I can't cancel the document or do anything with the printer.

  
  

  How can I fix these errors?

  Hello
   
  1. did you of recent changes on the computer?
  2. who is the manufacturer of the printer?
   
  Try these steps and see if you can print without problem.
  Step 1: Update of the printer.
  1. visit the printer manufacturer and check whether there is an updated driver.
  Visit this link for more information: http://windows.microsoft.com/en-US/windows-vista/Update-a-driver-for-hardware-that-isn ' t-work properly
   
  Step 2: Run Microsoft troubleshooting to solve the problem.
  1 visit the following link and click on "Run now", follow the instructions to run the Troubleshooter: http://support.microsoft.com/gp/printing_problems
  2. print and check if you are able to print multiple documents without any problems.
   
  If the problem persists, contact the manufacturer of the printer.
   
  I hope this helps.

  Kind regards
  Syed
  Answers from Microsoft supports the engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Entry interface errors

  We see entry errors on the Gi0/1 interface on cisco 1941/K9

  Also, after reset the counters, we see these errors is cumulative once in 2-3 hours

  Any suggestions where to start?

  See logging no signal is today all the...

  #sh int gi0/1
  GigabitEthernet0/1 is up, line protocol is up
  Material is CN Gigabit Ethernet, the address is bc16.2222.1111 (bia bc16.2222.1111)
  Description: For the LAN-Lehavim
  The Internet address is 172.16.55.2/29
  MTU 1500 bytes, BW 1000000 Kbit/s, 10 DLY usec,
  reliability 255/255, txload 3/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  KeepAlive set (10 sec)
  Full-Duplex, 1 Gbps, media type is RJ45
  control output stream is not supported, control of input stream is not supported
  Type of the ARP: ARPA, ARP Timeout 04:00
  Last entry of 00:00:00, 00:00:00 exit, exit hang never
  Last clearing of "show interface" counters 07:15:19
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0
  Strategy of queues: fifo
  Output queue: 0/1024 (size/max)
  30 second entry rate 5911000 bps, 2439 packets/s
  exit rate of 30 seconds 14787000 bps, 2919 packets/s
  72815038 package, 3854388881 bytes, 0 no buffer entry
  Received 16169 broadcasts (5648 multicasts to IP)
  0 Runts, 0 giants, 0 shifters
       entry 46 errors, 0 CRC, 0 frame, invaded 46, 0 ignored
  Watchdog 0, multicast 16164, break 0 comments
  78723290 packets output, 1917039290 bytes, 0 underruns
  0 output errors, 0 collisions, 0 resets interface
  870 drops of unknown protocol
  0 babbles, collision end 0, 0 deferred
  carrier, 0 no carrier, lost 0 0 interrupt output
  output buffer, the output buffers 0 permuted 0 failures

  Yesterday was 1120 errors.

  In show processes cpu sound there is no cleats

  Hi you entered mistakes and cost overruns at the same time

  This means that your more using the interface, too inbound, buffers are filled and drops traffic when its maxed out

  It's Cisco response to exceedances

  In a small number of cases, the overrun counter can be incremented due to a software fault. However, in the majority of cases, it indicates that the capacity of the interface has been exceeded. Nothing can be done on the router that reports of cost overruns. If possible, the rate at which frames are to come should be controlled at the remote end of the connection. Otherwise, if the number of exceedances is high, the equipment must be upgraded.

• How to read Wireless Interface error

  I have a few questions about this error on the interface.

  (1) what could be the problem and the solution for the mistakes of this interface? I noticed that the number of output errors multiply.

  (2) why the number of errors is different from the interface of two?

  (3) how to know either the AP or external antennas is defective? This access point is a 1200 series.

  AP #sh int dot11Radio 0

  Dot11Radio0 is up, line protocol is up

  Material is 802.11 G Radio, the address is 1111.1111.1111 (bia 1212.1212.1212)

  MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Last clearing of "show interface" counters 17:19:47

  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 7338

  Strategy of queues: fifo

  Output queue: 0/30 (size/max)

  5 minute input rate 5000 bps, 6 packets/sec

  5 minute output rate 243000 bits/s, 145 packets/s

  1034266 package, 1153540007 bytes, 6 no input buffer

  Received 6155 broadcasts, 0 Runts, 0 Giants 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  entry packets 0 with condition of dribble detected

  1171797 packets output, 443779394 bytes, 0 underruns

  449 output errors, 0 collisions, 0 resets interface

  0 babbles, collision end 0, 0 deferred

  0 lost carrier, 0 no carrier

  output buffer, the output buffers 0 permuted 0 failures

  AP #sh int dot11Radio 1

  Dot11Radio1 is up, line protocol is up

  The material is 802. 11A Radio, the address is 2222.2222.2222 (bia 2323.2323.2323)

  MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

  reliability 255/255, txload 2/255, rxload 1/255

  Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Last clearing of "show interface" counters 17:20:11

  Input queue: 0, 75, 2, 0 (size/max/drops/dumps); Total output drops: 7775

  Strategy of queues: fifo

  Output queue: 0/30 (size/max)

  5 minute input rate 3000 bps, 5 packets/s

  5 minute output rate 528000 bps, 144 packets/s

  241379 package, 35065157 bytes, 4 no input buffer

  Received 4941 broadcasts, 0 Runts, 0 Giants 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  entry packets 0 with condition of dribble detected

  686438 packets output, 149994557 bytes, 0 underruns

  291 output errors, 0 collisions, 0 resets interface

  0 babbles, collision end 0, 0 deferred

  0 lost carrier, 0 no carrier

  output buffer, the output buffers 0 permuted 0 failures

  Rare exceptions, errors always will... increase the key factor is "how (what sort of) errors," and "how long are they produced."

  It is a common process in troubleshooting to reset the counters (XXX clear interface counters) and analyze them for a period to determine the error rate (how fast the mistakes happen).

  You can also use this time to investigate whether counters increase because of some external actions (a Manager or some other iXdXiXoXtX standing in front of the antenna, for example).

  (2) you can activate one both antennas and measures on the ground with a laptop running Netstumbler (www.netstumbler.com , it's free) and compare the results of one antenna compared to another.

  Good luck

  Scott

• Industrial communications for CANopen - interface create error

  Hello

  I am trying to run a few basic examples, I found with the finder example in communication industrial directory - NOR - for CANopen-> cRio-> FPGA bitfiles-> CANopen_cRio_heartbeat.vi.

  But the block 'create an Interface' gives me the error 2147136667.

  I work with with module NI 9881 cRio. The module is connected to the robot from Festo.

  You please any idea what can cause this error?

  The text of says error:

  Possible reasons:

  You try to start an interface that is missing the bus for the transceiver power. Some physical layers on the material OR CANopen are fed internally, but others require an external power supply so that the port to operate. This error occurs when starting an interface on the equipment that requires an external power supply when no power is detected. Power supply right to your transceiver. Refer to the material of the NOR-Industrial communication CANopen Book for CANopen help for more information.

  See you soon

  Ivo

  Hello T.t,

  The 9881 must be fed outdoors. You can do with a CAN of junction box or with a Câble CAN.

  Concerning

• Interface VLAN traffic information

  Hi all

  Could someone please advice what traffic demonstrated Interface VLAN?

  For example, I have two interfaces, VLAN 10, and I created the layer 3 Interface VLAN 10.

  If I monitor the traffic of 10 to VLAN, the two interfaces combined traffic statistics?

  Thank you

  Prasanna Kumar deully

  Oh sorry I thought you meant span monitor where you register the interface traffic combined with the terms of a vlan

  To answer your question, it will display the number of ip layer 3 traffic in packets to all interfaces grouped under the vlan, then Yes, the two interfaces will show the interface of layer 3 vlan, some platforms will also show some L2 information like below and its shows 30 sec count on VLAN interfaces, but number five on the physical interface FA0/1

  Vlan149 is up, line protocol is up
  Material is EtherSVI, the address is 0008.e3ff.fd90 (bia 0008.e3ff.fd90)
  The Internet address is x.x.x.x/24
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  KeepAlive not supported
  Type of the ARP: ARPA, ARP Timeout 04:00
  Last entry of 00:00:14, exit ever, blocking of output never
  Last clearing of "show interface" counters 24w4d
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0
  Strategy of queues: fifo
  Output queue: 0/40 (size/max)
    30 second entry rate 2134000 bps, 381 packets/s
  exit rate of 30 seconds 2019000 bps, 460 packets/s
    L2 switching: ucast: 30595061 pkt, 2268569227 bytes - mcast: 0 pkt, 0 bytes
  L3 in Switched: ucast: 5882988002 pkt, 1908218042989 bytes - mcast: 1623 pkt, 775020 bytes
  L3 on Switched: ucast: 5579358870 pkt, 1872959920772 bytes - mcast: 322 pkt, 138259 bytes
  5886751734 packets input, 1885010127367 bytes, 0 no buffer
  Received 0 emissions (28 of IP multicasts)
  0 Runts, 0 giants, 0 shifters
  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored
       5618600472 packets output, 1854023804196 bytes, 0 underruns
  0 output errors, 0 interface resets
  output buffer, the output buffers 0 permuted 0 failures

• Enable SNMP to send blocked due to the loop network interface

  Dear community,

  We had a customer who has created a loop on his layer access and STP blocked some interfaces in order to protect the network.

  Normal behaviour until now, but we would like to receive the device, when these events occur, usually when an interface is set to err - disable or close (I guess it's more err - disable).

  We noticed that somehow the concerned interface was sometimes stay down without checking back and maybe change her status.

  I tried a few commands such as:

  Server enable SNMP traps stpx root-incompatibility incompatibility loop-inconsistent

  Enable SNMP-Server intercepts the port security (this is probably more for quantity of excess on the interface MAC)

  I also found a nice MIB called Cisco-Err-disable

  But I have the feeling that I missed something on the side of the device,

  Any help in setting this up would be greatly appreciated,

  Thank you

  STP will not put the port in err-disable mode.   The mib, CISCO-ERR-DISABLE report when the port is placed in a State of err - disable one of these events published in the MIB:

  CErrDisableFeatureID: = TEXTUAL-CONVENTION
  Current STATUS
  DESCRIPTION
  '- Integer value assigned to several functions/events.
  This error can disable a system entity

  Uni-directional: unidirectional link detection

  bpduGuard: Spanning feature Tree BPDU Guard that prevents
  treatment of BPDU packets on an interface to access

  channelMisconfig: bad configuration of aggregation of General links

  pagpFlap: Link Aggregation of Cisco PAGP protocol errors

  dtpFlap: Dynamic Trunking Protocol errors

  linkFlap: heartbeat of status of links

  l2ptGuard: Tunnel Protocol L2 errors

  dot1xSecurityViolation: 802. 1 x of violations of authentication

  Addition: breaches of Port

  gbicInvalid: invalid errors GBIC (examples):
  GBIC not taken in charge being inserted)

  dhcpRateLimit: DHCP snooping rate limit violation

  unicastFlood: unicast flooding threshold violations

  veterinarians: VLAN Membership Policy Server are related errors

  stormControl: Storm control (unicast, multicast, broadcast)
  threshold violations

  inlinePower: inline power errors

  arpInspection: errors detected by dynamic Arp Inspection
  Feature (DAI)

  portLoopback: Interface Loopback error

  packetBuffer: error on Buffer packets

  macLimit: errors by a function limited Mac address

  linkMonitorFailure: followed link failure

  oamRemoteFailure: Remote failure detected by Ethernet OAM
  (Operations, Administration and Maintenance) function

  dot1adIncompEtype: 802.1ad ether-type incompatible errors

  dot1adIncompTunnel: 802.1ad Pdu Tunnel Incompatible errors

  sfpConfigMismatch: incompatibility of the SFP configuration

  communityLimit: violations of Community limit Vlan

  invalidPolicy: violation of QoS policy

  lsGroup: errors by the State group link tracking feature

  ekey: errors by a key error mechanism

  portModeFailure: failed to change Port mode

  pppoeIaRateLimit: errors by an Agent through PPPoE
  Speed limit feature

  oamRemoteCriticalEvent: Ethernet OAM critical event remote
  Failure

  oamRemoteDyingGasp: Ethernet OAM remote Dying Gasp failure

  oamRemoteLinkFault: remote fault of the Ethernet OAM of link failure

  MRP: Errors detected by multiple VLAN Registration Protocol

  The switch will generate traps with:

  # Server enable snmp traps errdisable

  -Dan

• 2950 and 1410 errors

  Problems with errors in packets between a 2950 and 1410. Size of packets to 1500 and send 50000 I get about 98% ok. Also with a 3550 switch I get zero errors with this same test... Any ideas? It's between the radio and this 2950 switch.

  power on the 1410 injector is your problem. the CRC errors you get idicates that you have a duplex mismatch. The power injector is set hard auto negotiate it cannot be changed. The problem arises when you set your switch and integral ethernet on 100 duplex radio interface. Fight the logic here and set everything to auto. my P2P radio prod radio, passed a bad 2 Mbps to 20 Mbps. attention also with your signal - db. -40 dB to-54db should be good. You don't want to run hot (-19 dB to-30 dB), your performance may suffer.

  also glazing will reduce your signal. 1410 radios that can take time, so let them on the roof. I bench tested these radios and got 25 mb/s to 43-52db, it can be done

• 2 IOS Firewall interface

  Hello - I have a 3640 that is segment 2 internal LAN. There are 2 ports fastethernet on the box. I can't ping a network to another and vice versa. Even with all the icmp access allowed in both directions. I can however ping insofar as the router on both sides. The router can ping all customers on each side.

  When I do a sh ip road, it shows the two directly connected networks even if it does not show 2 subnets divided into subnets. Also with controls different debugging, I see that the packages be droppped. Errors are no way of ip Routing, the udp port any source, ip address is our interface, there is even an error saying wrong cable type.

  Here is a copy of the configuration.

  !

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  no service tcp-small-servers

  no service udp-small-servers

  !

  hostname 3640GW

  !

  Enable

  !

  IP source-route

  no ip-server name

  !

  IP subnet zero

  no ip domain-lookup

  IP routing

  !

  !

  no ip inspect the audit trail

  inspect the IP tcp synwait-time 30

  inspect the IP tcp, finwait-time 5

  inspect the IP tcp idle time 3600

  inspect the IP udp downtime 30

  inspect the IP dns-timeout 5

  IP inspect a minute 900 low

  IP inspect a high minute 1100

  IP inspect 900 low max-incomplete

  IP inspect high 1100 max-incomplete

  inspect the tcp host incomplete-max 50 IP block-time 0

  !

  FA 0/0 interface

  no downtime

  Connected wireless description

  IP 192.208.127.199 255.255.255.0

  IP access-group 101 in

  KeepAlive 10

  !

  FA 0/1 interface

  no downtime

  Connected to the CORP description

  IP 192.208.126.199 255.255.255.0

  IP access-group 100 to

  KeepAlive 10

  !

  ! Access control list 100

  !

  no access list 100

  access-list 100 deny ip 192.208.127.0 0.0.0.255 any

  access-list 100 permit udp any eq rip all rip eq

  access-list 100 permit icmp any 192.208.127.0 0.0.0.255

  !

  ! Access control list 101

  !

  no access list 101

  access-list 101 deny ip 192.208.126.0 0.0.0.255 any

  access-list 101 permit udp eq rip all rip eq

  access-list 101 permit icmp any 192.208.126.0 0.0.0.255

  !

  router RIP

  version 2

  network 192.208.127.0

  network 192.208.126.0

  No Auto-resume

  !

  !

  IP classless

  no ip address of the http server

  !

  Any help is appreciated.

  Gavin.

  What exactly are you trying make here? In an ACL, 'ip' includes 'icmp', so the first line of your ACL 100 and 101 deny ICMP packets. The following two lines are probably not do anything since the two RIP UDP and ICMP, as I said, are included in "deny IP" on the first line.

  In fact, your lst in each ACL line says allow packets in the interface with an IP address of the interface to other destination, will never happen.

  In fact, more I watch this, looks like you have the ACL applied to each interface. If you apply ACL 100 to 101 for the fa0/1 and fa0/0 then this will probably do what you have to do.