Freeconferencecall bridge

Similar Questions

• The most convenient airport in Bridge mode lose packets

  Hi all.

  I have an airport extreme with the version of firmware 7.7.7 (later at the time of this announcement). My modem ISP settings are blocked and it is already fixed to make routing/DHCP/Nat, so I use my airport extreme in Bridge mode to avoid the double NAT (it connects connects to the ISP with DHCP router).

  Both the ISP modem/router and Airport extreme are creating two different 'wifi networks", which belong to the same network (192.168.0.0).

  I can enter each of this Wifi network, obtain an IP address in both cases and start using the internet.

  However, when I use it on my ISP router, everything works perfectly, however, when I use it on the airport network, it fails from time to time.

  If I start ping an external IP address (e.g.: 8.8.8.8), I've never lost a packet on the network of the ISP router, but I lose packets often on the airport extreme network.

  Also, if I ping the ISP of the airport extreme network router I lose packets from time to time. Sometimes also vice versa. I never lose packets when ping the router whose network providing I'm connected to.

  All the settings on the airport extreme values by default (except that I created an additional network of 5 GHz).

  Can you give us some advice as how to solve the problem? I read somewhere that disable ipv6 connection sharing could solve the problem, but it didn't. Thanks in advance

  If you have the Ethernet cable from your ISP router that is connected to the "O" on the AirPort Extreme WAN port, unplug the cable and plug it into one of the three ports LAN <>- on the airport to see if this will help with the issue.

  However, if you have the Ethernet cable from the ISP router already connected to one of the LAN <>- port on the AirPort Extreme, then you'll need to reset the AirPort Extreme back to default settings and then set up again.

  If you have any further questions, the Airport extreme is defective and must be replaced.

• Bridge of Airport Extreme wireless

  Hi all

  I have an airport extreme and I wanted to install a wireless bridge.

  IM on the 2nd floor and my router is on the 3rd floor

  my wireless signal is weak on the 2nd floor, so I wanted to bridge so that I get full signal wireless 2nd floor also

  I do not want to use cable (from the router to the most extreme airport)

  can someone explain to me how to do this

  Thank you

  Hi irfan_mu,

  Check this help page: AirPort base stations: install and configure a wireless network extended (802.11n) - Apple Support

• Thunderbolt manual bridge IP no longer works with Sierra

  I use a Thunderbolt bridge with manual IP connection to connect 3 mac to my main MacPro, since the update of Sierra I can't connect one of the mac via the manual / plus static IP.

  Please HELP, am I missing something? It has worked before and now it no longer work.

  Joe

  Anyone?

  My work is stationary, and my staff is looking at me.

  Help, please!

  I also note that since the Sierra update whenever I connect to the server via the LAN cable or stroke, it appears this box, -that use only to appear only once (when I put in place) and hten again, unless I have re - install the operating system.

  Perhapse it is a new way to set up an IP Maunaul or I've never done right. Help, please.

  I pay my staff to do nothing right now.

• How can I configure my Airport Extreme in Bridge mode (use the 3rd party router)?

  Data sheet:

  Airport Extreme - v 7.7.7

  Luma Surround Wifi 8

  I recently bought a wifi (luminance) surround system.  It comes with 3 routers that you place around your home.  Unfortunately I still have stains died in my house I'm looking to add my Airport Extreme (AE) to Luma network.  Is it as simple as plug the AE to the network (via Ethernet) and the bridge mode selection in the configuration of EI?

  I can see the AE of my iMac, and it is green.  How do you know that actually extend the wifi of my router Luma range?

  I searched the forum and all messages dealing with this are several years old.

  Thanks for your time...

  Basically, you want to create a mobile network with your Luma and AirPort Extreme routers. As you said, the extreme would need to be connected to the luminance by Ethernet and reconfigured as a bridge.

  In addition, the following are also required on the extreme:

  • Wireless mode: create a wireless network
  • The network name must be the same as that used by the Luma.
  • The type of wireless security and the password must match that of the luminance as well.

  To 'know' that the extreme extends the network of Luma, simply consult the BSSID value in the drop-down of OS X Wi - Fi. It must match the ID of the airport on your base station. Note: You must hold down the option key before clicking on the icon of the free Wi - Fi connection.

• Bridge on the homepage on biggest tunderbird - start page

  When I opened tunder bird the bridge is very low

  I need more

  https://addons.Mozilla.org/en-us/Thunderbird/addon/theme-font-size-changer/

• Bridge mode breaks down wireless network

  I have a Time Capsule of 4th generation, I am creating an additional wifi network at the back of my house to cover a dead zone.  I'm not trying to extend an existing wifi, I seek to create a new wifi network but have it on the same network range as my network existing.

  My ISP is a router that I have in my basement that has wireless on it. .  It powers up to one router links AC that all my devices connect to.  Then, this device provides wired and wireless access to most of the House.  However, I have a task of dead at the back of the House for the wifi.  So I have an Ethernet cable, which goes to the back of the House and who connects in port WAN on the Apple Airport Extreme / Time Capsule (4th gen).   If I set this device to create a new wireless network in bridge mode, it works for about 20 minutes to an hour and then causes a sort of problem on my network and all my other devices go crazy.  If I disable the router from Apple or back to NAT, everything's fine.

  The only reason why I don't want to do this NAT device is because if I put it up to NAT then devices connected to the apple Airport extreme will have more access to the apple TV on the main network.

  So I need no more shots on why the bridge mode does not work on the router from apple or I need to know how to get Apple TV visible on two different IP ranges at the same time.  Unfortunately, the Apple TV can be connected to both wifi and wireless at the same time.

  Anyone have any ideas?

  Bridge should work fine... I would suspect that your TC gives signs of decomposition.

  It is now more than 3 years old which is the best before date.

  Try again using static IP method... I think it is more successful than the bridge.

  Should be enough information in this post... but if not just give me all the IP info from the existing modem router to. I can then give you specific info to set the TC.

  Re: time capsule Airport Guard disconnection

• Bridge mode... Router and TC

  My internet does not work if I have my xfinity on bridge mode router and my TC on mode bridge?

  Bridge on the modem/router and Bridge Mode on the TC will not work.

  Xfinity modem/router must be configured as a modem only simple only (in bridged Mode), and the TC must be configured in router Mode of DHCP and NAT

  or

  Xfinity modem/router must be configured normally as a modem/router, and the TC must be configured in Bridge Mode

• Blank Superhub &amp; TC Bridge Mode

  Hi all

  I am based in the United Kingdom and e through our internet a blank Superhub (handset cable modem / router) I want to connect my TC and use the network wireless of my TC, but maintain the Superhub wireless as well.

  I implemented the TC mode bridge on the network tab. I was then the port connection WAN on the TC to the Superhub, but it kept crashing the superhub. So, I went and connected to one of the LAN of TC ports to the port ethernet on the Superhub.

  It connects okay and I can get on the network without wire of TC, but it will not allow internet access. When I unplug the TC, I have to reset the router.

  Any help appreciated. All of this used to work very well, and then the Superhub has physically changed by Virgin for a update.

  I have not changed anything in the Internet tab in the AIrport utility, do I have to?

  Other objects related to the Superhub are a Bridge Sonos and Apple TV (both wired).

  Thank you

  The TC is defined to create a wireless network... SHOULD NOT EXTEND wireless.

  Although I doubt that it would be even possible to put in place this way.

  The internet tab must be configured for DHCP... but let me suggest another installation program that I find my best.

  Static IP address.

  I did a very complete post here with details.

  Re: time capsule Airport Guard disconnection

  If you need assistance please give me real info of the Virgin router... its IP address and the DNS and gateway, you found on the client machines.

  From this, I can give you together more specific instructions.

• Using the Airport Express Terminal as a bridge

  I would like to get video Amazon on my older Blu - ray player.  I was wondering if I could use my old AirportExpress (1st generation) as a bridge.  Now my new Comcast modem connects to my Time Machine that gives me my wireless connection. I tried to connect to the airport & connecting to my Blu - ray via ethernet cable, but I just get a flashing yellow light and the DVD on the screen tells me just the internet connection failed. Is this possible?

  Now my new Comcast modem connects to my Time Machine that gives me my wireless connection.

  I think that you wanted to say that you have a Time Capsule that produces the signal of your wireless network, correct? (Time Machine is a software on your Mac used to back up the Mac on another hard drive).

  I was wondering if I could use my old AirportExpress (1st generation) as a bridge.

  In 'bridge', do you mean you want the AirPort Express to receive a wireless signal of the time and then wireless Capsule to deliver one Ethernet signal to the DVD player?

  The answer is 'yes' to the offer that you really have a 1st generation AirPort Express. To check, look for the model number on the side of the Express in the small print. It starts with an "A" followed four digits.  A 1st Gen AirPort Express is A1264 model number.  What is the number that you see?

  I tried to connect to the airport & connecting to my Blu - ray via ethernet cable, but I just get a flashing yellow light and the DVD on the screen tells me just the internet connection failed

  Assuming you have a 1st Gen Airport Express, the device must be set up and configured to work with time Capsule. The AirPort Express doesn't quite work simply by plugging.

• Garage double NAT &amp; DHCP - bridge Possible issue error

  Help...

  So it's my game on a yacht...

  I have a MacMini (run bootcamp Windows 7 Pro), so actually it's a PC.

  • I use internal WiFi adapter of the MacMini to get my internet connection of various different Marina I could stay in
  • I then share the connection with the internal LAN adapter WiFi adapter WiFi
  • This allows me to share the WiFi port with other devices on the yacht

  Then I have an AirPort Extreme-

  • I then run an Ethernet on the MacMini Port CAT6 cable
  • on port WAN on AirPort Extreme
  • AirPort Extreme now has an internet connection (from the marina, WiFi)
  • I then activated the WiFi on AirPort Extreme to create a WiFi network on the yacht
  • and it gets its internet connection from the WAN port, which comes in turn the MacMini, which in turn comes from the Marina WiFi

  Connected to the AirPort Extreme are-

  -iPhones, iPads, MacBook, Apple TV, Smart TV, etc etc.

  -Some devices are connected using the LAN ports and AirPort Extreme cable

  -Some devices are connected by WiFi using WiFi airports

  I want DHCP to be handled by the AirPort Extreme-, mode I set as "DHCP and NAT".

  What is the problem-

  • AirPort Extreme shows an error
  • "double NAT and DHCP.
  • and suggested I turn it in Bridge mode
  • but I don't want to do that

  Any thoughts?

  Concerning

  Tim

  Would help if we could get the exact message you see.  You will probably need to change the DHCP-range on the AirPort Extreme to a different value, and then use the option 'Ignore' the Double NAT then the airport will show a green light.

  You will have to live with the Double NAT if you want AirPort Extreme to act as a remote router that provides a private network.

• Received annoying pop-up "there is no set application to open the moat bridge URL: gvr:MoatSuperV22._i_.b.u.»

  While I was surfing teamofgreekz.com on Safari 9.1 on my Macbook Air Yosemite (10.10.5), I received this strange window pop-up that follows:

  «There is no set application to open the moat bridge URL: gvr:MoatSuperV22._i_.b.u.»

  Eight more windows with the same message popped into the estate. I rebooted my Macbook immediately afterwards without pressing any of its options (cancellation, change in Document, search App Store), so I wasn't able to get a screenshot, only the message. A quick search on Google for this supposed URL does not work, but after searching the substrings in it (moat-bridge, greater Vancouver and MoatSuperV22), it could be related to Minecraft. Weird, since I don't have Minecraft on my computer and there is no advertising associated with Minecraft on the teamofgreekz.com site.

  I was not able to reproduce this weird pop up, but I'm writing to find out if someone has encountered this and has any input. Thank you.

  Hello..

  If this happens again, delete cookies from Safari.

  In your Safari menu bar, click Safari > Preferences then select the Privacy tab, then click: delete all data Web site

  Then exit and restart Safari.

• Pogo &amp; bridge base online sites, kicked by the window javascript without error message or of wrnings; requiring reloading. IT OFTEN!

  Since June and all 3 or 4 FF updates; I got updates Java, Adobe Flash, of big Windows 7 and my Avast antivirus program. Since then, I had a lot of problems with the bridge Pogo.com and Bridge Base Online game; When I used 2 power play games. Now, I can't even finish a game without being launched.

  I created new profiles; replaced new facilities of all of these programs (including FF) and even went to earlier versions. None of them has solved the problems. I also made sure to do Mode without failure and turned FF parts or disable, as suggested in all the troubleshooting tips, etc. Also the same for other programs. Everything indicates that the errors in the Javascripts. on these sites or in their or FF. I'll go to IE and try to use it again. I hate it but no choice, up to what something is fixed.

  Worked! Very useful! Already transmitted person-to-person on Pogo!

  Thank you very much.

  Wolverine655

• Airport Express connects to my WiFi bridge

  Hello world

  It is searched many Web pages and throughout the Apple support forums, but I still could not understand...

  I bought recently Airport Express to extend my Wifi in another room and thus use it for AirPlay. My existing WiFi network is set up by the router, Asus RT - N12 (it is connected to our modem from the vendor to the scale of home - isn't available). I want to my Airport Express to work as bridge, connected to the existing network and to serve as extension and receiver airplay.

  It works only when I connect Airport Express via LAN cable to the Asus router and set it as the new network. This is not convenient because it is located near the router and does not provide any additional coverage to our Wifi.

  I tried to set up the base Airport Express "Extend existing network." But once set, it REQUIRES connection via cable. To connect to the existing WiFi network, there is NO other choice. This option is missing in the Airpot utility, so I can't select the Wifi to connect to.

  In addition, when I connect to the Airport Express Terminal cable to the WAN port (which is our wall of our home modem), you do not find the internet connection for some reason any (while Asus has no question to do).

  I'm quite desperate here. I already think to buy Airport Extreme. But I don't know if he will be able to connect to the internet for the same reason. And, it is five times more expensive. Everything else works with Asus without problems and additional parameters. iPhones, iPads, Apple TV, Android phones, Mac Pro, laptops Windows (except old 3G iPhone that says that it cannot connect to the network).

  Any ideas where to look for a solution? None of the settings in our modem Asus to allow the airport as bridge recommended? And, above all, WHY is configuring lack the ability to connect to the existing Wifi network and wants to connect via cable ONLY?

  Thank you...

  I want to my Airport Express to work as bridge, connected to the existing network and to serve as extension and receiver airplay.

  Unfortunately, function of "extend a wireless network" Apple is an exclusive feature that has been designed by Apple for only wireless "extend" the signal of another Apple wireless router.

  Or, another way of saying the same thing would be to say that, if you want to extend the wireless network, you will need two routers Apple for this purpose.

  In other words, the function 'extend' is not compatible with 3rd party routers, so the only way that you will be able to get the Express at work... or any other router from Apple, incidentally... would do what you did and plug the Express using a wired Ethernet cable connection.  If you cannot run the Ethernet cable, then you can take a look at a pair of Ethernet over Powerline (EOP) adapters to eventually send the signal on power lines the existing AC in your House.

  If you only want to use the AirPort Express for AirPlay, it might be possible for the Express to 'join' the wireless network... but the Express won't provide any additional wireless signal coverage by joining a wireless network.

• Can I use a wireless bridge mode?

  I have problems with NAT Type 2. I want to disable the appearance of shaping of my Time Capsule and continue to use wi - fi. I thought I knew how to do this after selecting the bridge Mode and place all cables ethernet in making <>_, that the Wireless does not work, as in, it looks good in Airport utility, but I can't connect to my devices. I should add that there is a switch/hub between the TC and the modem cable. Why wi - fi does not work?

  What is the number and model of your modem?

  We ask for the type of modem you have will determine whether or not you can have a switch between modem and Time Capsule.