Similar Questions

• Cannot install Windows Update error 80070570 code.

  OT: dates.

  Almost none of my top dates are up dating. I get code 80070570. I need help!

  http://Support2.Microsoft.com/kb/947821/en-AU

  Difficulty errors of corruption of Windows by using the DISM tool / System Update Readiness

  or

  Manually, try to install updates from Microsoft Download Center.
  a. visit the Microsoft Download Web site, type the number of "KB" of the update in the search box and press ENTER.
  b. in the list of search results, click on the (KB) Knowledge Base article link to go to the download page. If there is more than one list, look for a link that goes to the Microsoft Download Center.
  c. If there are several versions on the download page, find the appropriate for your computer. Click on the download button and save the update to your desktop.
  d. When you are prompted, click open to install the update.
  Microsoft Download Center

  http://www.Microsoft.com/en-us/download/default.aspx

• Several update failures, sfc scan in safe mode not working do not with a WRP, new error 80070570 installation error. USB installation failure...

  I don't know why but it questions

  (1) the win 7 install dvd (retail), it comes with an error 80070570
  (2) Usb key with win7with sp1 do not fare any better either
  (3) several chess update with error with no. support messages either.
  I tried all known and a few new patches, it comes
  Scan of SF,
  Hot Fix
  Update device drivers
  RAM memory modules
  Repair installation
  Recovery Console
  Safe mode startup
  Isolation of CBS newspaper.
  Reformat and reinstall at least 20 times on 3 separate hard disks
  MB reset
  Incremental update
  SP1 iso dvd and usb stand-alone installation
  Check disk and every known, all make mistakes recovery console on NEW and OLD INSTALLED IN WIN7
  Distribution
  Virus on, defender of victory off the coast
  Safe mode / with all combinations on
  Microsft onseven and support forums
  I'm starting to think that this could be a deliberate attempt to make me go buy win8
  I need help please
  Krish

  Hello

  1. the Microsoft updates you aren't able to install?
  2. What is the accurate and complete error message you get?
  3 have. what troubleshooting measures you tried to solve the problem?

  I suggest you try to install the updates to the clean boot. Clean boot helps eliminate conflicts of software that occur when you install a program or an update or when you run a program in Windows. You can also troubleshoot or determine what conflict is causing the problem by performing a clean boot.

  How to perform a clean boot in Windows
  http://support.Microsoft.com/kb/929135

  Note: Follow How to reset the computer to start as usual after a clean boot troubleshooting article KB929135 to reset the computer in normal mode.

  I hope this helps. Let us know if you have other problems with Windows in the future.

• Have an older iPad that I inherited. iOS is outdated but get error message when I try to update. Support instructions do not match my iPad. This was bought in 2011 I think.

  Have an older iPad that I inherited. iOS is outdated but get error message when I try to update. Support instructions do not match my iPad. This was bought in 2011 I think. I need help to remove the update one put it back.

  CBTEKRONY wrote:

  Have an older iPad that I inherited. iOS is outdated but get error message when I try to update. Support instructions do not match my iPad. This was bought in 2011 I think. I need help to remove the update one put it back.

  What is this error message that you receive? This would help a lot. From there, a person must be able to provide some additional troubleshooting steps.

• I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

  I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

  Drive, interface in the crankcase of training controller, or the USB port or the cable may be faulty.

• I have the version 7.0.1 of firefox and cannot access the cookie settings, I get errors indicating cookies are disabled, but cannot find anywhere in the Privacy tab that allows me to manage cookies.

  I have windows XP - Pro and recently upgraded to Firefox 7.0.1 and OE I get errors from web sites on cookie settings. I can't access the cookie settings via the tab tools option and privacy, because there is no option of cookie except to erase or delete individual cookies. I could manage my cookies before but something has changed in this version of Firefox, and now it's playing a lot of features of my web site.

  See all the parameters of the story and the cookie to use:

  • Tools > Options > privacy > Firefox will be: "use the custom settings for history".
  • http://support.Mozilla.com/kb/cookies
  • https://support.Mozilla.com/kb/enabling+and+disabling+cookies

• Hi, I just bought a used 2012 Pro 13 "Macbook. It came with iMovie installed. However, I would like to get the update to iMovie. He said: I can't update iMovie because a different Apple ID was used to download iMovie and I get errors. How can I update iMo

  Hi, I just bought a used 2012 Pro 13 "Macbook. It came with iMovie installed. However, I would like to get the update to iMovie. He said: I can't update iMovie because a different Apple ID was used to download iMovie and I get errors. How can I update iMovie?

  Error message #1: these applications cannot be accepted by your Apple ID. These applications have already been assigned to another Apple ID, and they will be available in this list of purchases Apple ID. If you don't have access to this Apple ID and would like to receive future updates, you will need to purchase applications.

  Error message #2: update are not available with this Apple ID. This update is not available for this Apple ID either because it was bought by another user or the item has been refunded or cancelled.

  Error message #3: we could not complete your request. There was an error in the App Store. Please try again later. (null)

  Unfortunately, free updates are available to the original purchaser of the computer. The iMovie is locked to his Apple ID, so unless you have to grab his ID, you can buy iMovie.

• I get error # 4005 when I try to reset my iphone via itunes 6.

  I get error # 4005 when I try to reset my iphone via itunes 6. The iphone is frozen with the screen showing that it wants to connect to itunes. I made sure my itunes and software mac was up to date, tried to restart my computer and tried different usb ports and I always get the error code 4005 every time. I am also using the same cable of load supplied with the phone.

  Are there more options for me to unlock my phone?

  If you have tried all the steps mentioned in this article and you are still not able to restore the phone, contact Apple for repair.

  If you see errors 9, 4005, 4013, 4014, when you restore your device iOS - Apple Support or

• Pair of M30 - 604 with installing identical software - Modem gets Error 633

  Hello

  I have a pair of Satellite M30 604 s running Microsoft Windows XP SP2, the same Office 2003 Enterprise, Norton SystemWorks 2005 software. All was well at least the last 6 months.

  I recently installed Norton GoBack part of SystemWorks, this may or may not be connected to the problem, it's just the latest thing that has been installed.

  A single machine whenever you try to connect through software Modem on COM3 TOSHIBA gets Error 633.

  Have studied the problem even backed up a machine and restored that to the defective one, still no error.

  Any ideas, or I might have to strip the thing down by using the recovery disks, is not prepared, in view of the time it will take to get back to where he is - without this annoying fault.

  Seems to be the hardware failure or conflict as now make a full recovery.

  [Edited by: admin on 16 July 05 08:54]

• Get error Code 12 as he tried to use the ExpressCard 8360 VXI card

  Dell XPS M1530 laptop computer using, under Win XP SP3.  Everything went very well with the same material in September 08.  Now, I am getting error Code 12, "this device cannot find enough free resources that can be used. (Code 12) ».  I tried disabling other devices in my laptop as the large map broadband and media without change in the symptom slot.  Is there a better way to understand what is happening and to restore my computer to work with the MXIExpress card?

  
  

• I tried to solve the problems to the existing solution in this forum. I still get error 50405

  Dear,

  I use USB-6009 for controlling pumps, valves, and two Mass Flow Control. Each two cycle I get error 50405. I tried to solve the problems in the existing solution in this forum, but the error always showing each cycle 2 of the operation. I enclose my VI filled for the expertise, I was wondering if its design issue? Home shot of the error screen. Thank you.

  You have certainly a few design issues.

  The structure of stacked sequence tends to create more problems than it solves. I the have not used in new programs since version 1.2 of LabVIEW (in 1989). A state machine is a much better choice of architecture.

  Local variables can cause race conditions, copies of additional data, poor performance and it is difficult to debug code. There are special cases when they should be used, but these conditions are not in your code. Just wire directly on the terminals of control at the scene, the data will be used.

  My guess on the likely cause of your error is the use of several DAQ Assistant to perform the same task (with different data values) in each image in the sequence structure. With the arcitecture state machine that I suggested above, you would need one. The DAQ Assistant trying to be clever on the configuration and tasks of closing, but different instances do not speak with each other, so they don't know when to release the resources.  You might be able to do work if you used the DAQmx screw standard you have done with the task of digital output.  You do not connect the error lines of the DAQ Assistant for you can be missing errors.

  Indicators and controls without legend may be a troubleshooting nightmare. Please give each control and seeing a unique label. If you don't want the visible label on the front, you can use the properties of the control to hide. If you want multiple controls to have the same visible text for the operator, use the legend.

  Learn how to use subVIs. Most of the code in the 6 images of the structure of internal sequence is identical. By converting only a Subvi, you would reduce considerably the size of the diagram and if you ever need to modify the code, it should only be changed in one place - the Subvi.

  The while loop in frame 0 of structure of outer sequence is a "gourmet" loop He's going to run as fast as possible and seize all available CPU resources until the user presses a button. Put a wait function (ms) in the loop with expectation of ~ 100 ms. best, learn how to use the Structure of the event for user input.

  The second loop inside of the structure cases inside does nothing and can be removed.

  Many of these objects suggest that you have a programming background using the text-based programming language.  LabVIEW uses a paradigm of data flow that avoids largely for things such as the structure of the sequence and the local variables. I recommend that you work through the tutorials online on the Getting Started with LabVIEW.

  Lynn

• Each cycle of operation of 5 I get error 50405

  Dear,

  I am trying to solve this problem for the last month, it make me crazy every day.
  I posted the same post ago last month and I got the answer from the experts OR, that its the problem of leting the vi running for only 5 cycle (previously showed only after 2 cycle), after the 5-cycle the error appear again.

  More information link

  I tried to solve the problems to the existing solution in this forum. I still get error 50405

  Here's my vi updated seal and some information, hope someone can help you resolve this error.

  Thanks for your support and help Lynn.

  Hi MESHA'AL,.

  Error-50405 is normally related to an error in communication between your device and your computer. I suggest updating your DAQmx driver to the most recent who will support your version of LabVIEW. See the compatibility chart for more details.

  I also suggest upgrading your computers USB drivers and try the different USB ports, hubs and even the cable if you have another.

  If possible, try to run your program on another computer to see if you can reproduce the behavior on another system.

  Finally, if the presists of the error, try to run some of the sample code provided with LabVIEW so we can narrow this down to a problem with your code. At this point I'm leaning more towards a driver/hardware however problem.

• Why do I get error-229771

  Hello

  I recently downloaded labview in order to write a scenario that would take measures of voltage of a battery by using the NI USB 6008 case. My code has worked fine until I extended my trial labview for the period of 45 days. I receive the error 229771 making reference to my DAQ assistant. Is it possible for me to solve this problem?

  Thank you

  You search the forum for the error code? There are a few posts showing solutions.

  For some reason you need to leave the sign less for the search to work.

  This could be a good starting point:

  I get error-229771 to Task.vi DAQmx Start?

  Steve

• Why do I get error 200428 executable?

  I had a NOR-DAQ application correctly by using a project under development LabVIEW 8.6 and 8.8 NOR-DAQ.  When I use the same exact project to build the executable on the same PC, I get error 200428 - "measures: value passed to the control task/channels is not valid" when starting.  How could it be?  I use tasks DAQ built with the DAQ Assistant and stored in the project.

  For the record, I solved this problem by importing for MAX kept project file: Build\Data\NI-DAQmx.ini.  It imported all my tasks DAQ to MAX and the executable is now working properly.  Thank you.

• HP Pavilion M8200N Ctr Media: Get Error Message When I run as the recovery disc for my HP M8200N media center pc

  When I ran the disk recovery software, I keep getting error screens, they all started "a problem has been detected and windows has shut down to prevent damage to your system.   I re-ran about 10 times about 5 different error messages.  None of the proposed solutions would work since I coundn't get to Windows.  Safe Mode respectable and cmd failed after loading files. Could not get to checkdsk /F. could not get t check material are another anywere in windows.  I tried Yes No. and recovery of the plant.  Has been a long path towards the resumption of the plant.

  Reminder of my problems with my HP:

  My HP Pavilion M8200N Ctr Media had a blue screen in the past and I've never had a problem wiping the drive, refomatting it and my running recovery disks.  I had Crypotolocker beginning of the year and cleaned the machine and manually deleated 35 k corrupt (masked and not masked).  The PC then worked for a month when a blue screen frooze it and I could not reset the registry.  I tried to clean the disc, but it wouldn't work.  Records recovery and rescue, did nothing.  Finally, I tried and old version of XP that leaves me in the drive, but the drive size 1/2 gig would only up like 131meg.

  I tried to buy a new drive for teribyte 1, but recovery software would not rcognize it.  Then, I took the reader to original HP and connected to my Linux box with Gparted on it (a powerful software partitioning and recovery).  GParted fixed the HD.  I created 3 partitions on it.   I then tested all partitions to copy files and pictures in them and then get back them.  3 all partitions functions correctly. Then I reinstalled the HD in the HP M8200N.

  When I would run recovery disk, which has always worked in the past, I got these error messages:

  IRQL_NOT_LESS_OR_EQUAL

  CDFS_FILE_SYSTEM

  Make sure you have enough space

  NFTS_file_system

  on behalf of those that I remember well.

  Someone at - it solutions to this problem.  My wife loves his HP desktop computer and cannot use the new laptop, so any suggestion is appreciated.

  You have focused on potential problems with the hard disk have you considered maybe it's memory? If you know how to run gparted, I'm sure you can use memtest86. Make the bootable media and run a full test at startup and see if the RAM is good.