GET overhead VPN

Similar Questions

• What ports should I use to get the VPN RA worked?

  Hello

  I have a few tunnels l2l. I don't use "vpn sysopt connection permit" command. I prefer to activate the required ports for specific source IP. So they can establish the VPN tunnel with me.

  Recently, I have configured remote access vpn. It is work very well... But only when I activate "vpn sysopt connection permit.

  Question:

  1. what ports need to be activated to get RA VPN work? (without vpn sysopt connection permit)

  2. How can I restrict the access of remote when clients they connected to my private network?

  Thank you

  Leo

  Hi Leo,

  When you are not using 'connection sysopt... '. ", you must explicitly permit udp 500 and udp 4500, traffic esp on the outdoor access list.

  Let's say that public intf outside ip address is x.x.x.x and pool customer, we use y.y.y.0 and you want to allow 'only' traffic for port 80 through the tunnel.

  In the ACL on the outside, you need the following instructions:

  access-list 101 permit udp any host x.x.x.x eq 500

  access-list 101 permit udp any host x.x.x.x eq 4500

  access-list 101 permit esp any host x.x.x.x

  access-list 101 permit tcp y.y.y.0 255.255.255.0 eq 80

  access-list 101 deny ip 255.255.255.0 y.y.y.0

  * Please indicate the post if it helps.

  -Kanishka

• Get the VPN without dedicated key server

  Hi all

  We plan to implement Get VPN in our collection company and place the pieces necessary to complete setting up VPN access. And I have a question about the present.

  Do we really need a dedicated server key? I mean I know that the key server cannot be a member of the group, but here's my question. I have a router that is configured for some voice features. And I do not want to be a member of my VPN infrastructure get (but it will be on the network and available to offices and remote sites). If this router can be configured as a server key and still perform other services such as speech or other things? I really need to know if this can work.

  I'd appreciate a quick and accurate answer that this forum is my last resort. Thanks in advance.

  -Jay

  Hi Jay

  You must be a key server, as is the router that will push the political security to members of the group. But it cannot be part of IPSec connections that is, not a member of the group.

  You can run other services and features on this router. But it should not affect the ISAKMP and GDOI traffic among the members of the group.

  Regarding

  Kings

• How can I get the Client VPN or NAT - ted connection

  I installed a router on a customer site to replace a PC that made the NAT on a cable modem connection.

  On the router THAT NAT is done to get all the s PC on the LAN to access the Internet.

  But... one of the users use a VPN client to get to his office. With the PC, there is no problem, but given that the router is in place it can not connect.

  Because I specialized on switched networks my knowledge; edge of NAT and VPN clients.

  Is there anyone who knows how to get this VPN client-session user to be NAT - ted?

  Kind regards

  Martijn Koopsen

  If you have some onfigured of overload, then you tap the traffic. In all cases, you should at least be able to establish a connection, as IPSec uses UDP 500 for the negotiation of the tunnel. If you are not able to pass all traffic, it is another question. Once the tunnel is established, the traffic can be encrypted using the Protocol ESP who cannot be tapped under normal circumstances. If this is a cisco IPsec client, then you must discover which is the feature of termination. If it's a hub 3K, you could activate IPSec over UDP to the problem of circumvention the ESP

  Hope that helps

  Jean Marc

• VPN connection: An unexpected error has occurred.

  I am suddenly unable to get my built-in VPN connection works on my iMac with OS X 10.11.5.  I get the VPN connection message: an unexpected error has occurred.  I have been using this VPN configuration to connect to work for several months with success.

  But last week (and I do not know if it had nothing to do with it), I went on vacation and used a free wi - fi setup of Tim Hortons.  I had a LOT of trouble getting the next login page, and I checked all playing with different settings of network without success.  When a change did not work, I put it to its original setting.  Finally, I learned to use Safari to access the free WiFi connection page of Tim.  Then once connected, everything was OK.

  But when I returned a week later and if necessary, to start my VPN connection to access the work, it wouldn't start.  I checked and recheck all my settings preferably of different network, but did not find those who were wrong.  I even deleted and re-entered my VPN service definition without solving the problem.

  Thinking that the problem could be the newly installed ISP of Bell equipment (we went from Rogers while I was away), I used my BlackBerry smartphone (issued by my employer) to create a wi - fi hotspot and accessed to the internet using this connection which completely ignored my home ISP equipment.  But still, I was unable to establish a VPN connection.

  I then tried my iPad VPN connection, and it worked!  Then, I defined a VPN service on the iMac to my wife and the iMac to my daughter and was able to successfully establish a VPN connection to my work very well, using exactly the same VPN configuration.  This led me to the conclusion, it was a problem on my iMac (and not with my new ISP or VPN system of my work that had none of the changes you made), but I still can't find what is "broken".  I run Onyx for my iMac OS X 10.11.5 and repaired permissions and clean the cache and all the rest she is doing to "solve" problems.  But the problem persisted.

  Is there a preference file corrupted somewhere (scan option is no longer on the current version of the Onyx for a reason any)?

  I still have a network setting wrong somewhere I need to go back to the system is correct value?

  Here is the attempt to VPN from the file system.log (with some hidden values in the case where they display my work VPN access):

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: received an order to start SystemUIServer [257]

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: changed to connecting status

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec connection to server nnn.nnn.n.n

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: phase 1 of the IPSec from.

  26 June at 16:13:48 Myrons-iMac raccoon [520]: agreed to the takeover of vpn connection.

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec connection to server nnn.nnn.n.n

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: connection.

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec Phase 1 started (initiated by me).

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: bind 1 (cannot assign requested address)

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: sendfromto failed

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: Phase 1 negotiation failed due to the error of sending. 94437eb7d5b1b6e8:0000000000000000

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: can not send packets

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IKE Packet: send failed. (Initiator, aggressive Mode 1 Message).

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: Controller IPSec: IKE FAILED. Phase 1, assert 0

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed by disconnecting

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec disconnection from the server 142.201.5.6

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec disconnection from the server nnn.nnn.n.n

  26 June at 16:13:48 - last message repeated 3 times-

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed to offline, terminus right no

  Any help or insight would be more useful and appreciated... so that I can work from home again.

  Thank you

  Myron VanderLaan

  I finally found my VPN problem.

  There is a 'racoon' file that is generated when I connect to the VPN to my work site.

  I have created a modified version of this file so that my connection does not expire in 3600 seconds (changed in 24 hours).

  Apparently, there are some slightly different settings (such as certain IP addresses other than VPN IP of my work) in this file under our new ISP Bell from the former FAI Rogers.

  And if I connect to the WiFi Hotspot from my BlackBerry, it does not once again because these settings in the file are different again.  I must return the file generated instead of my modified file.

  Bad luck!

• I want the password protect the VPN toggles

  IM aiming to put a lock on the VPN code switches as a means of Internet security. So far, using a VPN internet filter was the best method of filtering * sites because the restriction in iOS setting is either

  (1) too broad - the parameter filters too many sites that are not 'bad' according to my criteria and Internet which uses a hassle or

  (2) not wide enough and inefficient - if I have to enter each unique web address, that I want to block by hand, I'll never be able to get all of them.

  OpenDNS umbrella VPN is inexpensive ($20 years OLD!), relatively fast, be online most of the time and is effective. The only problem is, as many have said, Apple provides no way to get the VPN settings.

  Jailbreaking would provide tweaks to do this, but I don't want to go this way (although I feel that apple encourages this line).

  I looked in other methods, like the Ciscos Maraki new mobile device management. As a professional IT Tech. tool, maybe it's the best option, but it is not always easy for a novice to networking semi guy like me to understand.

  Fundamentally, I believe that Apple needs to work on its policy of the device settings. They need develop a control system easy to use and easy to use. Families and small businesses are ever needing management tools complete device for all levels of mobile devices. access to the network, access app, followed by the app, ext.

  I want to control and monitor the use of my family, it's so dangerous content out there and new ways to hide profane and damaging activities opens too quickly for an individual to find ways to control us needed tools to help us.

  Submit your Apple here:

  http://www.Apple.com/feedback

• access VPN r7500

  I can't get my VPN to work. It connects, but not change my IP address and allow me access to my network home.

  Here is my configuration:

  Comcast - router in Bridge mode

  -Nighthawk R7500

  -Macbook pro with tunnelblick (tried both viscosity)

  I have a dynamic DNS, which has been well updated, I tried all the options VPN configurations (tcp, udp, auto, home network only, all the network domestic sites and internet, even made manual configurations in the vpn file to try to force something.)

  The problem is; I can connect to the VPN server, but that's all. Nothing changes, I can't access my home network, my IP address does not change, I don't know what it is even made or connect to. I installed a dozen files configuration doing this, and one of the reasons why I bought this router was due to the VPN. Any help would be greatly appreciated, I really want this VPN to work.

  OK I thought about it. I went the subnet of my
  Network servant 172.16.x.x and it works fine now.

• Cisco VPN problem with security update KB3057839 for Vista

  Someone had problems with any connection Cisco VPN works after the installation of update of security KB3057839 for Vista? When this update is installed, the pop-up to enter the password and user id not come, need to use the Task Manager to close the program. The first time I went back to the restore point to get my VPN to work, this time I tried to reinstall the VPN but that doesn't work anymore. I started to uninstall updates (had 7 of them), when I got to it, KB3057839, the VPN began working again.

  Mike

  See this on the real issue:

  http://www.chiark.greenend.org.uk/~sgtatham/PuTTY/wishlist/Vista-update-breaks-config.html

  It turns out that the logon dialog box is invisible, but still, it agrees to enter you your password and LOG you!

• Connect to the router VPN using PPTP (Ubuntu)

  Hello

  As I mentioned in other post, I try to get the VPN works for my Ubuntu workstation. I'm not an expert of VPN, so I need help.

  So far, people seem to agree that pptp is easier to config that IPSec (under Linux platform). Select the PPTP Protocol and add a user account for the Linksys router.

  Now, the Linux part.

  I have pptp-linux installation (it is the best client for linux pptp seams). I try to set it up, but I missed something relatd to coding or something.

  I try to follow this documentation: https://help.ubuntu.com/community/VPNClient#PPTP

  When I run this command: pon myvpn nodetach

  I get the following error:

  Using interface ppp0
  Connect: ppp0 <-->/dev/pts/2
  MPPE required, but not executed [v2] MS-CHAP authentication.
  Connection down.

  Here is the log of the router:

  15 Oct 21:51:02 2008 Client Remote System Log [] disconnect PPTP server.

  Kind regards

  Hello

  Thanks for your help and this useful link.

  I have change my configuration file and I managed to set up the pptp connection.

  Here the configuration file that I use (for people with the same problem):

  RemoteName until-vpn
  LinkName until-vpn
  ipparam entmd-vpn
  Pty "pptp exemple.dyndns.org - nolaunchpppd.
  name budderball
  usepeerdns
  require mppe
  garbage-eap
  /noauth
  file /etc/ppp/options.pptp

  Also, I change the contents of/etc/ppp/chap-secrets:

  Budderball until vpn-based *.

  With this configuration, I can launch the tunnel and communicate with the gateway and LAN.

  Here the command line I use to establish the connection and than create road so that any request for 192.168.1.0/24 use the ppp0 interface.

  sudo pon entmd-cpn debug dump logfd 2 nodetach

  sudo route add - net 192.168.1.0 netmask 255.255.255.0 dev ppp0

  Finally, by reading the documentation, I found a plugin for Network Manager. It's a work like a charm.

  For ubuntu: sudo apt - get install network-manager-pptp

  An installation, you must restart to 'activate' the plugin. (this is a bug)

  You can use the network - manager to configure your pptp connection. I intend to post a wikiw on the Ubuntu Wiki page.

• Cisco Cisco IPSEC VPN to encrypt but not decrypt

  Hello

  I have a vpn ipsec problem.

  packets are encapsulated and décapsulés but only in one direction. I don't understand why.

  VPN is already mounted on another router, I want to change the router but can't get the vpn have the new router

  Thank you for helping me

  PS: Sorry for my English

  Hello

  I looked at the configuration of your router RT-897VA once again, and I don't know if static NAT statements in there are supposed to work or not, but they won't because you have not specified any inside and outside interfaces. Configuration changes below correspond to the configuration of your router RT, check if their implementation makes a difference (the changes are indicated in bold):

  RT-897VA #show run
  Building configuration...

  Current configuration: 3933 bytes
  !
  ! 11:56:34 configuration was last modified THIS Friday, November 4, 2016
  !
  version 15.4
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  RT-897VA host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  !
  No aaa new-model
  clock timezone THIS 1 0
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !

  !
  !
  !
  !
  domain IP XXXXX
  IP-name 194.2.0.20 Server
  IP-name 194.2.0.50 server
  IP cef
  No ipv6 cef
  !
  !
  !
  !
  !
  Authenticated MultiLink bundle-name Panel
  VPDN enable
  !
  VPDN-Group 1
  ! Default L2TP VPDN group
  accept-dialin
  L2tp Protocol
  virtual-model 1
  tunnel L2TP non-session timeout 15
  !
  !
  default value for the field
  !
  !
  !
  !
  !
  !
  !
  CTS verbose logging
  license udi pid C897VA-K9 sn FCZ2030DL
  !
  !
  username password privilege 15 itef 0...
  !
  !
  !
  !
  !
  VDSL controller 0
  !
  property intellectual ssh rsa keypair-name XXX
  property intellectual ssh version 2
  !
  !
  crypto ISAKMP policy 1
  BA aes
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA aes
  preshared authentication
  Group 2
  ISAKMP crypto key cleidentique address IP-WAN-B
  !
  !
  Crypto ipsec transform-set aes - esp esp-sha-hmac toto
  tunnel mode
  !
  !
  !
  crypto map ipsec-isakmp TUNNEL 1
  counterpart Set IP-WAN-B
  Set transform-set toto
  match address TUNNEL-DATA
  crypto map ipsec-isakmp TUNNEL 2
  counterpart Set IP-WAN-B
  Set transform-set toto
  match TUNNEL-TOIP address
  !
  !
  !
  !
  !
  !
  ATM0 interface
  no ip address
  Shutdown
  No atm ilmi-keepalive
  !
  interface BRI0
  no ip address
  encapsulation hdlc
  Shutdown
  Multidrop ISDN endpoint
  !
  interface Ethernet0
  no ip address
  Shutdown
  !
  interface GigabitEthernet0
  Description BOX-SWITCH
  switchport trunk vlan 101 native
  switchport mode trunk
  no ip address
  spanning tree portfast
  !
  interface GigabitEthernet1
  no ip address
  !
  interface GigabitEthernet2
  no ip address
  !
  interface GigabitEthernet3
  no ip address
  !
  interface GigabitEthernet4
  no ip address
  !
  interface GigabitEthernet5
  no ip address
  !
  interface GigabitEthernet6
  no ip address
  !
  interface GigabitEthernet7
  no ip address
  !
  interface GigabitEthernet8
  WAN description
  IP address IP WAN - A 255.255.255.240
  IP virtual-reassembly in
  NAT outside IP
  automatic duplex
  automatic speed
  card crypto TUNNEL
  !
  interface Vlan1
  no ip address
  !
  interface Vlan101
  VLAN-DATA description
  IP 192.168.101.251 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  !
  interface Vlan111
  VLAN-TOIP description
  IP 192.168.111.251 255.255.255.0
  IP virtual-reassembly in
  !
  IP forward-Protocol ND
  no ip address of the http server
  no ip http secure server
  !
  !
  IP nat inside source static tcp IP 25 expandable 25 192.168.101.2
  IP nat inside source static tcp IP 80 80 extensible 192.168.101.2
  IP nat inside source static tcp 192.168.101.2 extensible IP 443 443
  IP nat inside source static tcp 192.168.101.31 3201 IP extensible 3201
  IP nat inside source static tcp 192.168.101.31 80 extensible IP 3280
  IP nat inside source static tcp IP 443 33443 extensible 192.168.101.11
  overload of IP nat inside source list NAT interface GigabitEthernet8
  IP route 0.0.0.0 0.0.0.0 XXXX (ADSL router)
  IP route 192.168.100.0 255.255.255.0 IP-WAN-B

  NAT extended IP access list
  deny ip 192.168.101.0 0.0.0.255 192.168.100.0 0.0.0.255
  IP 192.168.101.0 allow 0.0.0.255 any
  access list IP-TUNNEL-DATA extents
  IP 192.168.101.0 allow 0.0.0.255 192.168.100.0 0.0.0.255
  TUNNEL-TOIP extended IP access list
  IP 192.168.110.0 allow 0.0.0.255 192.168.111.0 0.0.0.255
  !
  access list IP-TUNNEL-DATA extents
  IP 192.168.101.0 allow 0.0.0.255 192.168.100.0 0.0.0.255
  permit tcp host 192.168.101.3 192.168.0.0 0.0.0.255 established
  TUNNEL-TOIP extended IP access list
  IP 192.168.111.0 allow 0.0.0.255 192.168.110.0 0.0.0.255
  !
  !
  !
  control plan
  !
  !
  MGCP behavior considered range tgcp only
  MGCP comedia-role behavior no
  disable the behavior MGCP comedia-check-media-src
  disable the behavior of MGCP comedia-sdp-force
  !
  profile MGCP default
  !
  !
  !
  !
  !
  !
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  privilege level 15
  password...
  opening of session
  transport input telnet ssh
  line vty 5 15
  privilege level 15
  password...
  opening of session
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  !
  !
  !
  end

• Client VPN 3.7.2 on Redhat 7.3

  Hello

  Try to get the VPN 3.7.2 caces charged under Redhat 7.3 with kernel 2.4.18 - 10.

  I downloaded the kernel.org kernel (2.4.18) and it located in usr. I have then run, do, make dep, and make install to create all the necessary files (including autoconf.h, version.h etc.).

  I then installed the Cisco VPN client - taking of the default values for all the locations of files etc. The module seems to compile fine with no error messages, however when I try to run a 'start vpnclient_init' de/etc/init.d, I get the following:

  [ [email protected] / * / init.d] #. / vpnclient_init start

  From/usr/local/bin/vpnclient: /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec:

  unresolved symbol skb_over_panic_Rsmp_2344b59d

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol dev_base_Rsmp_c89 pending

  e6c24

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol alloc_skb_Rsmp_20 pending

  791234

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol skb_under_panic_R pending

  smp_36e2a71b

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol register_netdev_R pending

  smp_e2549a3a

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol xtime_Rsmp_f31ddf pending

  83

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol add_timer_Rsmp_a1 pending

  9eacf8

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol del_timer_Rsmp_fc pending

  62f16d

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol __global_restore_ pending

  flags_Rsmp_54dd1dcb

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol dev_add_pack_Rsmp pending

  _25791be4

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol unregister_netdev pending

  _Rsmp_2dd2d775

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol __global_cli_Rsmp pending

  _64576b05

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol printk_Rsmp_1b7d4 pending

  074

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol kfree_Rsmp_037a0c pending

  BA

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol __kfree_skb_Rsmp_ pending

  8cbe73da

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol __global_save_fla pending

  gs_Rsmp_5d902e96

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol kmalloc_Rsmp_93d4 pending

  cfe6

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol eth_type_trans_Rs pending

  mp_3c74ec43

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol jiffies_Rsmp_0da0 pending

  2D 67

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol do_gettimeofday_R pending

  smp_72270e35

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec: symbol dev_remove_pack_R pending

  smp_878a87ec

  /lib/modules/2.4.18-10/CiscoVPN/cisco_ipsec:

  Tip: You are trying to load a module without a GPL compatible license

  and unresolved symbols. Contact the provider module for

  help, only they can help you.

  Can anyone help point out where I should be looking. I reinstalled several times but the problem persists.

  Thanks for your help.

  Barry

  Research on the release notes for the 3.7.2 looks like there may be a bet caveat with Linux which is the origin of the current problem. Take a look at this link http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel3_7/clint372.htm#xtocid22

• PPTP VPN or IPSEC for Android and iPAD

  Being new on the RV180 (and routers VPN besides) I had trouble getting a VPN's, supporting my iPad and Android devices. However, I understand that an IPSEC connection would be a safer sollution. Unfortunately I can't find a clear statement anywhere to do it.

  I found descriptions/parameters in the different RV180 of the setting of the (few) in mobile platforms. So far not managed to get the installation program.

  Little help to start would be great!

  Thank you very much.

  Ronald

  Hello Robert.

  My name is Chris and I work at the Cisco Small Business Support Center.

  The PPTP option will be much easier to install, and most devices have a built-in capability of PPTP.

  The RV180 supports the IPSEC tunnels, but only for links from site to site or a remote user with the client software.  Some of the other features of our support SSL VPN connections, which would allow you to use the Cisco Anyconnect client available for android, but SSL VPN is not a characteristic of the RV180.

  On my Android (Droid X running Android 2.3.4) phone he built in VPN, IPSEC and PPTP client.  Yours is probably as well, but if not there should be a few apps available.

  If you decide to go with PPTP you can configure it like this on the RV180:

  1. go to the router admin page and click on VPN > IPsec > VPN users.

  2. check the box to enable the PPTP server.

  3. complete the range of internal addresses for your customers to use PPTP (192.168.1.200 - 192.168.1.210 for example)

  4. click on save.

  5. Once you click on save, you should be able to edit the table of parameters of VPN client.

  6. click on add, check enabled, enter a user name and password for the PPTP user to use and for the protocol type, select PPTP.

  7. click Save to add the user.

  Once this is done, you should be able to go into the settings on your Android device and add a VPN for PPTP connection.   Fill in the same information you setup of the RV180 and you should be able to connect.

  The server address will be the WAN IP of your RV180.

  As far as IPSEC goes, the process is similar but a little more complicated.

  1. on the router admin page go to VPN > IPsec > Basic VPN configuration.

  2. choose the VPN client for peer type.

  3. name connection (it is used on the router)

  4. choose a pre-shared key to be used with this connection.

  5. for remote WAN IP address, you can leave the default remote.com

  6. for the Local gateway Type, you'll want to choose IP

  7. to Local WAN IP select IP and enter the IP address of the RV180 (WAN IP)

  8. for LAN Local, enter the local network for the RV180 ID (default is 192.168.1.0)

  9. to the Local LAN subnet mask enter 255.255.255.0

  10. click on save.

  The steps above create a VPN IPSec tunnel using the default values of the router, which you can view by clicking on default settings under VPN > IPSEC.

  Now you just set your phone.  On my phone, I have an option for Advanced IPSEC VPN, but yours may be different, or you may need to use an application like a customer, if your phone does not have built-in IPSEC VPN.

  On my Droid X, I want to go wireless and networks, VPN settings, Advanced IPSEC VPN, add a new virtual private network.

  My phone uses models of connection, so be sure to choose one that fits your tunnel on the RV180 parameters.

  Enter the RV180 WAN IP address as the VPN server, as well as the pre-shared key, install you on the RV180.

  Make sure that all connection settings that you have configured on the RV180.

  You will also be asked for an internal subnet IP address, and for this, you must enter the Local LAN and subnet mask, that you configured on the RV180 in steps 8 and 9 above.

  I wish I could be more specific, but it seems that there are several different menus and options depending on what Android phone using your.

  I hope that this helps, but if not feel free to respond and I'll try to explain.

• Site to Site VPN filter

  I've set up a site to site VPN and I can't seem to get the VPN filter works. I've followed this document:

  http://www.Cisco.com/image/gif/paws/99103/PIX-ASA-VPN-filter.PDF

  I created an ACL and created an ACE with only traffic I want to allow. Then, I went to the site to site group policy and apply this filter. However, I can still ping remote network from a customer who should not be allowed. Remote network is 192.168.2.0/24.Here is my partial config:

  permit Test access extended list ip 192.168.2.0 255.255.255.0 192.168.1.2 host
  Trying to deny a range ip extended access list

  Group Policy internal Test
  Test group policy attributes
  value of VPN-Filter Test

  tunnel-group Test_tunnel type ipsec-l2l
  attributes global-tunnel-group Test_tunnel
  Group Policy - by default-Test

  Hello

  First of all I would like to clarify that the group name used for one site to the other tunnel tunnel must be the ip address of the host "at least for the tunnels l2l static" it's tunnel-g were you must apply this "Test" group policy, configuring the filter seems perfect, but you must make sure that you apply the strategy of Group accordingly. Now, once you apply group policy to the correct you have to bounce the tunnel tunnel-g otherwise the new filter will not take effect, you can use the command "erase the crypto ipsec his counterpart x.x.x.x" generate some traffic and bring up the tunnel is again he should have the filter.

  If you apply correctly and bounce the tunnel it will work.

  You can check if the filter is applied with the command "show vpn-sessiondb detail l2l" and find the name of the ACL

  Best regards, please rate.

• NAT, ASA, 2 neworks and a VPN tunnel

  Hello. I have a following question. I am trying to establish a VPN tunnel to a remote network used to be connected to our via a VPN tunnel. The problem is that the previous tunnel their share has been created for the x.x.x.x our coast network which will serve no more time a month, but is currently still active and used. As I'm trying to get this VPN tunnel as soon as possible without going through all the paperwork on the other side (political, don't ask) is it possible to make NAT of the new network in the network x.x.x.x for traffic through the VPN tunnel.

  Something like this:

  new network-> policy NAT in old x.x.x.x fork on ASA-> VPN tunnel to the remote network using x.x.x.x addresses

  It is possible to add the new policy, but sometimes it can conflict with the former.

• Using Cisco IOS Firewall VPN clinet

  Hello

  I configured RTR1 to support VPN Clients. RTR1 has a site 2 RTR 2 site VPN tunnel.

  Customer VPN connected to RTR1 have RTR1 LAN IP connectivity. How can I get the VPN Client LAN to access the local network RTR2?

  I've included the VPN Client LAN to be ecrypted in the VPN tunnel to the LAN RTR2 and Vice Versa. I also tried a static router configured on RTR2 for the LAN of Client VPN IP WAN RTR1 serving of next hop.

  Still doesn't work is not for me. Any ideas?

  Thank you

  The other side added your remote VPN client pool to its configuration? The remote site must know its interesting traffic as well. Is RTR2 NAT'ing? Cleaned the configs for the two routers would help a lot.