Group of channels on 2 switches

Similar Questions

• Added properties (Group and channel) are not a numeric data type.

  I use a use to add two groups and channel custom properties. The properties are text and digital, double and whole.

  When I create a request in the browser, I selects the custom using the drop-down list property, but has only the drop operator "=" or "<>". "" The property is displayed in the data portal is a number of float. I had this problem when I was adding properties custom by using a script. I then tried "Navigatorinstallation / my Index DataFinder/Reset/Reset", then repopulated my search box, using the use on my raw data files. At this point, all the properties of my have only the "=" or "<>" choice of operator in the query.

  It seems that my properties are digital in the data portal, but the the query string of the browser.

  Thanks in advance,

  Hi Bill,

  You don't have to delete the files.  Choose the NAVIGATOR menu "settings > My DataFinder > reset... '. "can clilck on the UPPER part of the two buttons, one called"reset the index.  Which will remove all records in database and re-index all of your data files.  If you one of these properties have already optimized, set their State not optimized before resetting the index, otherwise the optimized property data types will persist.

  If this does not help, then the problem could be in the use that you use.

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments

• How do you find the name of the Group and channel your TDMS file name?

  How do you find the name of the Group and channel your TDMS file name?

  Nevermind, I've used the file viewer.

• Firefox is not updated final 5.0b2 to 5.0 (beta channel) day after switching to the output channel

  I use 5.0b2. In b2, I went from the beta update channel on the channel of update release.
  Today 5.0 final is out, and Firefox does not update saying "your version of Firefox is updated.

  BTW, the "Channel selector" function is missing from the Firefox 5.0 and later versions. It has not been used as intended developers, so it's history.

  If the information provided from Helper7677 do not indicate that you have version 5.0 installed, download and install version 5.0 of yourself.

• Remove the port from the channel-group

  I met a strange problem with port aggregation, where I decided to remove a port of a port channel and put it in another, but in my SNMP tool, it still belongs to the old channel of port and the new at the same time.

  Port channel was created using:

  (config) #interface gigabitEthernet 0/1/22

  (config-if) trunk mode #switchport

  (config-if) active in mode #channel-group 1

  Then passes through

  (config) #interface gigabitEthernet 0/1/22

  (config-if) #no active mode channel-group 1
  (config-if) active in mode #channel-group 2

  I have also that when I pull up some information on configuring etherchannel.

  #show interfaces gigabitEthernet 0/1/22 etherchannel

  Port status Up Mstr Assoc in Bndl

  Group of channels = 2 Mode = active = Gcchange-

  Port channel = GC Po2 = - port-channel Pseudo = Po2

  Port index = 0 load = 0 x 00 Protocol = LACP

  Flags: S - device sends slow LACPDUs F - device sends Rapids LACPDUs.

  A - unit is in Active mode.        P - peripheral is in passive mode.

  Local information:

  LACP Admin Oper Port Port port

  Port flags State priority key number

  Item in gi1/0/22 SFT bndl 32768 0 x 2 0 x 2 0 x 117 0x3D

  Partner information:

  LACP Admin Oper Port Port port

  Key priority indicators Dev ID Age port key number status

  Item in gi1/0/22 SFT 32768 0817.35e4.2c80 26 s 0x0 0 x 2 0 x 118 0x3D

  Age of the port in the current state: 164d: 21 h: 32 m: 44s

  This could be a problem with my (observium) snmp tool or are there additional measures to eliminate a port of a group of channels? Reboot of the switch?

  System image file is "flash: c2960s-universalk9 - mz.150 - 2.SE4.bin.

  Hello

  I would say that it is related to the snmp tool, once you remove the port of the chain earlier and added to the new, which will be to the one, it is impossible that an interface will be less than 2 different port channels.

  Also there is no need to restart the switch or something like that, you can use the following commands to verify that the interface is now part of the new channel group:

  Show etherchannel summary

  Show interface execution item in gi1/0/22

  With these commands, you will see that the interface belongs to the Group channel 2, and the order that you set above shows that the interface belongs to po2.

  Hope this helps

• Series quick reading of the channel group properties

  Hi, can someone please advice what is the fastest way to extract about 400,000 files channel group properties? Currently I use DataFileLoadRed with only the Group of channels that interests me and channels stripped down to a single value by setting the no. intervals of 1 and SectionBegin / end of 1/2. Suggestions for improvements? PHEX

  An alternative would be to open all files with the following code.

  Option Explicit
  
  dim groupindex : groupIndex = 1 ' you can also use a groupname instead
  dim groupProperty : groupProperty = "description"
  
  ' include this in a loop over all your files
  dim filePath : filePath = "C:\temp\example.tdm"
  dim store : set store = navigator.ConnectDataStoreByParameter("TDM", ""& replace(filePath, "&", "&") & "")
  dim propVal : propVal = store.RootElements(1).Children(groupindex).Properties(groupProperty).Value
  MsgBox propVal
  

  The files are open and your properties are extracted. Potentailly datafinder approach should be more fast but if you don't get that market this may be a way out.

• What are the bare minimum commands to get a stack of PC6825 3 - switch with inter switch Link Aggregation?

  I am brand new to PowerConnect switches, even though I am familiar with the concepts of VLANS, aggregation of links and spanning tree.

  I am on a deadline to get some new ones installed 6248 in our baskets and get them functioning as a stack. What are the bare minimum commands for:

  • Three switches in a stack (master/Eve/member)
  • 2 ports grouped between each (total redundancy) switch with loops WITHOUT switching

  All the switches are running firmware v3.3.9.1 (January 2014).

  Thank you

  The range of interface Ethernet 1/g1-1 / g2 allows you to select the ports you want in the channel of the port. Page 293

  Channel-group 1 Auto mode to create 440 lacp lag page

  Select the Group of channels with interface port-channel 1

  Switchport page 601 in trunk mode

  Switchport trunk allowed vlan [VLAN you use]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF

• Lacp 3560 switch circuits

  I'm trying to run a trunk on a four port Lacp group to a form of switch netgear a 3560 but am stuck. Everything works fine if I place a chest with a single autonomous port, and that everything works when I use a group of Lacp 'switchport access' mode, but as soon as I activate "switchport trunk" each gi status goes to "suspended" and no traffic flows.

  Does anyone have any suggestions?

  Thank you.

  Andrew,

  Thank you for the additional information. The configuration of the ports seems to be ok now.

  After the Show etherchannel , physical ports are individual-State. This would mean that the switches did not negotiate the creation of the Association using the LACP Protocol and ports still work as four individual switchports.

  The neighboring switch talking LACP? If he is put in LACP active mode? At least one device must be in LACP active state, and both must talk to LACP. Maybe you could try to replace orders 1 channel-group passive mode 1 mode channel-group active in your configuration.

  Best regards

  Peter

• Several groups Etherchannel summary

  I have a strange problem with a port-channel configuration on my 6509 (IOS 12.2 (33) SXI4a) with redundant Sup720s.  Before going much further to try to remedy through experimentation I wanted to receive feedback from others, in case anyone has seen this behavior.  I think I know why it happened, but I would have preferred to better understand the reasons and also the best way to solve it.

  We have a lot of servers in our environment configured with double copper 1 GB interfaces running in a configuration of Etherchannel delivered to our core 6509 switch.  We use LACP (assets) to support reunification between switch and servers

  We started with some WS-X6148A-GE-TX-line cards installed in order to support the lower flow of our servers at the same time and save money.  These line cards are oversubscribed on a ratio of 8: 1 as far as bandwidth goes, and we received with this for quite a while.  It emerged last year that we had heavy - hitting a few servers that receive many a fallen executives as contactors interfaces were not able to follow, if we bought a WS - X 6748-GE-TX line card that is almost full-speed capable line by port.

  Because we wanted to migrate these servers to the new card online with minimal downtime I thought the easy way to do the following:

  (1) put two interfaces on the line-new map in the same group of port-channel ports currently in use for this server.

  (2) move a cable in one of the new ports and wait to get online in the bundle of this port.

  (3) move the rest of the cable in the port of other new and confirm that it delivered.

  (4) remove the two old ports on the map in slow-line of the config of the channel port.

  Using this method with two servers to work pretty smoothly without breakdown in communication to servers.  However, I seem to have some odd leftover information in my config bothering me.  Here is an example:

  den-sw35aa #sh etherchan 36 short

  Flags: - Low P - D bundled in port-channel

  I have - autonomous s - suspended

  H Eve (LACP only)

  R - Layer 3 S - Layer2

  U - N running - is not in service, no aggregation

  f cannot allocate an aggregator

  M not in use, no aggregation due to minimum links has not met

  m don't use, port do not associate due to not meeting minimum links

  u - unfit to tied selling

  d default port

  w waiting to be aggregated

  Number of channels: 35

  Number of aggregators: 37

  Protocol for the Port-Channel port group

  ------+-------------+-----------+-----------------------------------------------

  36 Po36 (SD) LACP

  Po36A 36 LACP Gi2/9 (P) (SU) Gi2/19 (P)

  Last applied Hash Algorithm of Distribution: fixed

  As you can see, I have now two groups under this configuration of etherchannel port-channel.  No ports are assigned to the original Po36, and the new Po36A contains the two new ports.

  It also shows that I have 37 aggregators and only 35 groups of channels actually in use.  I wonder if this is going to happen with all the servers that I have to do and, ultimately, reduce the port channel groups total I can configure and I used.

  My idea of why this could have happened back to fundamental differences in the line cards themselves.  Going enabled card of tissue non-tissu a permit probably was a little too wait for a package of four way occur when I put all four ports in the group.

  As much as to get rid of him, I think to close the interface port-channel itself, then physical, then all ports put up in reverse order.  I hope that it would not come down to close the ports and left-hand config port all channel and reconfigure.  At worst a switch reboot, but it's absolutely a last resort, and if I were to conclude that it was to have some sort of negative performance impact.

  No previous experience or input would be appreciated.  I was unable to find anyone in the forum regarding documentation and a similar story has not received me any where.

  Best regards

  Ty

  Hello

  The following documentation talks about the behavior you're seeing. I do not know if you already took a glance at this document, but I'm still posting here for others who were not able to find it.

  http://www.Cisco.com/en/us/Tech/tk389/tk213/technologies_configuration_example09186a0080094470.shtml#po1A

  And for you to remove the aggregation switch reload or flapping interface would not help. I'm afraid you will have to reconfigure the portchannel again. It's the only way you can get rid of it.

  I hope this helps.

  Kind regards

  (TAC)

• Grouping of NETWORK cards causing the ESXi to retransmit ethernet frames received.

  I had an HP Proliant DL380 G5 ESXi 5.1.0 connected to a Cisco 3750 Switch stack.

  All by performing a tcpdump on a host without a report, I discovered that he was under the bombardment with ethernet frames for the MAC address of a computer virtual located on a host across the data center. After a few brief troubleshooting, I discovered that I was able to stop those erroneous frames by disabling NETWORK adapters on my VMWare host group.
  
  I believe that in my situation when ESXi is configured to use two network cards to all frames received on vmnic0 and retransmits them on vmnic1 and vice-vesa. I experienced these symptoms when ESXi is configured for failover with an active adapter and adapter mode standby and I also experienced the same symptoms in the following load balancing configuration.
  

  
  

  Symptoms: some time after activating the load balancing, all frames Ethernet for the MAC address of a virtual computer on the affected host are broadcast on each switch port in the entire data center.
  
  Steps to reproduce:
  (1) implementation below configuration.
  (2) unplug the ethernet cable connecting vmnic1 and switch1 port gi2/0/4
  (3) run the host 1.1.1.1 EI - n - q tcpdump on any machine physics linux in the data center (don't even have to be connected directly to 1).
  Confirm there is no packet seen with the IP address of 1.1.1.1 destination
  (4) plug the cable between vmnic1 and switch1 gi2/0/4 port ethernet
  (5) wait 60 to 120 seconds
  (6) watch a burst of frames ethernet with the destination MAC address of the VM (which owns 1.1.1.1) in the output of tcpdump

  Cisco Configuration:

  hostname switch1
  !
  src-dst-ip port-channel load-balance

  !

  interface GigabitEthernet1/0/4

  Description vmnic0.host0 (NIC 1)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  interface GigabitEthernet2/0/4

  Description vmnic1.host0 (NIC 2)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  Interface Port-Channel 4

  Host0 description

  switchport trunk encapsulation dot1q

  switchport mode trunk

  spanning tree portfast trunk

  end

  
  Configuration of ESXi
  vSwitch0

  Grouping of NETWORK cards / Load Balancing: route based on IP Hash
  Grouping of NETWORK cards / failover detection network: link status only
  Grouping of NETWORK cards / notify switches: Yes
  NIC Teaming / relief: Yes
  Grouping of NETWORK cards / adapters active: vmnic0, vmnic1
  NIC Teaming / standby adapters: nothingness
  NIC adapters grouping / unused: nothingness
  Security / Promiscious Mode: reject

  Security / MAC address changes: accept
  Security / forged passes: accept

  
  #1 Virtual Machine port group
  Network label: 'Public '.

  VLAN: 27
  Grouping of NETWORK cards: all unchecked (inherited)

  #2 Virtual Machine port group
  Network label: "trunk".
  VLAN: 4095
  Grouping of NETWORK cards: all unchecked (inherited)

  VM kernel Port #1
  Network label: 'management '.
  VLAN: 2

  Grouping of NETWORK cards: all unchecked (inherited)

  VM #1
  

  OS: Windows Server 2003
  NIC 1 / adapter: Flexible
  NIC 1 / network Label: 'Public '.

  IP address: 1.1.1.1/24

  I apologize for the delay in my response.

  Unplug physically 2 cable NETWORK card on the host and configuration mirrored port on the switchport to 1 NETWORK adapter of the host, I have been able to confirm that the host VMWare issues guides on NIC1 with a destination MAC address of one of its own VM.

  After carefully reviewing the captured data, I noticed that the destination frames wrong "02:bf:cb:50:a2:76" MAC address actually belonged to "Local Area Connection 1' one of my Windows 2003 Server WHAT VM installed on the suspected host.

  Dig a little deeper, I discovered that this virtual NETWORK card is presented to the operating system as
  Name: Local 1 network connection
  "Type: VMware Accelerated AMD PCNet adapt."
  MAC: 02-BF-CB-50-A2-76

  But the configuration of the virtual machine in vCentre is
  Name: Network adapter 1
  Type: Flexible
  MAC: 00: 0C: 29:fa:e8:83

  Note the different MAC addresses.

  Digging a little further I discovered that Windows 2003 server has configured on "Local 1 network connection" network load balancing and NLB is the cause of the altered MAC address.

  Rather than to investigate further I have just placed a load balancer linux before the server windows 2003 cluster and that you turn off NLB.

  But I suspect that there is still a fundamental problem in the Virtual Switch VMware with how he learns the MAC addresses of the virtual machine is using flexible vNIC. In particular, with a virtual machine that uses a form to override the MAC address such as that used by NLB.

• Questions of virtual switch VMware ESX 4.0

  I have two vmnic that I use for the service console, I have a current value and the other on the eve.  On the collection of NETWORK Adapters tab, I settled on 'Route based on the original virtual port code' load balancing.

  I have six vmnic used for a network of Virtual Machine, I have all of them the value active.  On the collection of NETWORK Adapters tab I I settled on "Route based on ip hash" load balancing.

  I have two vmnic used for a VMkernel network, I have all of them the value active.  On the collection of NETWORK Adapters tab I I settled on "Route based on ip hash" load balancing.

  I have the service console cables dating back to a Cisco Catalyst 3560 G, I don't have something special with these ports installation.

  I have the cables of the VM network dating back to a Cisco Catalyst 3560 G, I'm recommendations on this article: http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004048

  I configured 3 groups of channels on the Cisco for each ESX Server (with 6 ports each in each group). What should I do for the configuration of load balancing. In the best practices guide, it shows src-dst-ip. CBC - mac is set to by default etherchannel. If I turn it on to src-dst-ip I have to configure any IP address on the Cisco as the dst - ip or etherchannel takes care of that. What is the best practice for blaance of etherchannel load config?

  I have the VMkernel network goes to the two HP ProCurve 2910al switch.  I would like to divide one of each vmnic between two switches.  Not configure anything at the level of the switch for this?

  I would be grateful the help, thanks again.

  Although each ESX Server will require its own port-channel group independently. So you will have at least the same number of channel groups of port you have esx servers.

  There isn't any problem with not not using circuits.  If you are ending in expansion and maybe a different subnet for your virtual machine to access the creation, then channels will be required to spend more than one vlan to the port-channel group.

  Hope that helps!

  LB

• record channel times of order data NI_DataType

  I'm trying to replicate some features of selection of the control Data Logging property in the VeriStand workspace in a Labview application (I wish I could get just the VI for control of the workspace).  In the control of the registration of the properties-> channel category data the time channel can be selected.  When I select absolute time he records the system path = 'targets, controller, channels, Absolute System Time. "  But I have one property TDMS NI_DataType = 68.  If I manually select the channel (add channels) we obtain a = 10 NI_DataType.  The difference seems to be that the NI_DataType = 68 has the well formatted time (m/d/Y/min) while the NI_DataType = 10 at a time in a large number that represents the number of seconds.  The NI_DataType is read-only.  How can I get the formatting nice NI_DataType = 68 to be registered like that?  This post is treated?  If so how to do that?

  Thank you!

  I have found that the Group of channels TDMS (NI_VS Data logging API.lvlib) type def that gets wired for the new Data Logging Specification.vi has a def of time type of the channels Options which allow channels different time to be configured and named.

• Continuous sampling PlotStripChart DAQmx and multiple channels

  I modified the sample code sychAI DAQmx - AO.cws slightly to provide more output wavforms. I can read at the same time on a single channel without problem. Then when I try two channels I read in an array of N (N > have a lot of examples of PlotStripChart 2, N = 2 with 2 tracks so it updates a point at a time...) I don't want that.)  samples. 0 to N - 1/2 is what AO1 (output channel 1) written on, and N/2 to N - 1, that's what written AO2. Now, if I put the number of tracks 2 and try to draw on a stripchart I get the range 0 to N - 1 on both routes.

  How to draw a picture of say 10000 samples on 2 tracks with table grouped by channel?

  Thank you

  I changed my DAQmxReadF64 to the group by number of Scan instead of channel and set skipcount = 0 and staringIndex = 0 and which has worked exactly as I wanted... but according to documentation it should not work.

• Strange behavior. 2590 relay switch and Get position vi.

  I'm reading a PXI2590 1 x 4 MUX switch relays that I fires only when necessary. I know the names of the relays are MUX01, MUX23 and MUX0123. If I switch, niConnect channels INIT, wait Debounce and can get the Position of the relay, I get a correct reading (closed or open). I then called niSwitch close .vi and the switch remains in this position.

  However if I just called INIT, niSwitch getting the Position of relay and close vi seems the selector to a different value (default?). I confirmed this behavior using a HF generator and Analyzer of spec.

  Is what I do with these evil vi? Can I use DAQmx driver for this switch instead?

  LabVIEW 8.5.1

  OR-Switch 3.70.49152

  NOR-DAQmx 8.7.1f2

  NOR-PXI-2590

  Hello GovBob,

  Correct me if I'm wrong.  First you call OR-SWITCH boot (not initialize with topology) or initialize options with the 'reset device' Boolean is unwired? (which means reset = true)

  Then, in a case: call OR-SWITCH connect channels, wait OR-SWITCH Debounce, OR-SWITCH get relay post, then NOR-SWITCH close (close a session, not close relay).  Then physically measure opens or shorts.

  In the other case: appeal OR-SWITCH get relay post, then NOR-SWITCH close.  Then physically measure opens or shorts.

  The results are the second case has openings (ch0 is connected to the com).  This is expected behavior since the indicator 'reset the device' in one of the screws initialize is TRUE if left thread continues.  However, if you physically measure different values compared to what OR-SWITCH get post is back, so please submit your screws and a list of the steps and the values measured for each stage.  I hope this helps!

  -Jordan

• Use custom that sorts and types of lines in groups

  I need to create a synthesis in DIAdem report. I have provided the raw data of another person. The data are organized in time. There are essentially 3 types of different lines that contain completely different data. What I would do is to separate the types of lines in 3 groups, then have the channels data support located in their respective groups. I want to put the data found in the first row of 20 or so as properties of the root if possible. I understand that it is a big business, any help would be very helpful thank you.

  Is attached, the raw data and a diagram of the groups and channels (like what I'm looking for)

  I wonder by my boss to do some work that is signifcantly beyond my programming abilities (which are limited). So help me. Please, I beg you. Thank you.

  Hi adevins76,

  In fact, files *.log you sent are still missing at the time of the date/time string.  I forgot scan lines [UUT_TEST_LOG] in the root properties, now the does for *.txt files both use *.log (which encode information differently).

  Ask if you have any other questions,

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments