How do I configure jumbo frames

Similar Questions

• How to activate traffic iSCSI jumbo frames?

  Hi all

  I have my separate iSCSI coming out of a NETWORK card dedicated to one vlan traffic.

  Now, I have activated the switch to extended frames, qnas 869 pro for jumbo frames also and I (AFAIK) activated my extended frames ESXI host.

  However on the stats of the switch, I can't have counters increase jumbo frames.  others are but not huge.

  After reading all that I Although jumbo frames can help increase performance?

  So I appreciated if you could help me!

  Thank you

  Josh

  Well some how I made jumbo frames work on my ESXI host.

  I enabled frames for each unique interface on the ESXI host and on my NAS that provides iSCSI (qnap 869 pro), I enabled frames extended on both interfaces on it.

  Now it works no problem!

• VMware ESXi4.1 with Jumbo Frames on iSCSI (how to install?)

  Hello

  I've read various articles relating to ESXi 4.1 and frames. They all pretty much say the same thing. I'm having some trouble understanding step 3 in the section "Creating a Jumbo Frames - enabled VMkernel interface" in the link below. Could break you the order for me?

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1007654

  Step 3 says: to create a VMkernel connection with Jumbo Frame support, run the command:

  esxcfg-vmknic - a-i

  My stacked switches cisco 3750G are configured for frames.

  Thank you all. This is my first post.

  Mike

  Assuming you want to create a vSwitch separated with NIC dedicated to iSCSI traffic, you should do this:

  1.) create a new virtual switch, i.e.

  esxcfg-vswitch - an iscsi switch

  2.) enable Jumbo on this virtual switch, i.e.

  esxcfg-vswitch - m 9000 iscsi switch

  3.) create a port for the VMkernel module group

  esxcfg-vswitch - a GRPE-iscsi iscsi-switch ports

  4.) create VMkernel. You must specify an IP address for use with the VMkernel, and a network mask and the MTU size, i.e.

  esxcfg-vmknic - a-i 192.168.100.1 - n 255.255.255.0 m 9000 iscsi-portgroup

  5.) associate a physical NETWORK card with the new switch, i.e.

  esxcfg-vswitch - L VMNIC5 iscsi switch

  You must run the command-line jumbos steps since there is no GUI Option - at least none that I'm aware off the coast.

• The e2000 wireless router does support jumbo frames?

  I can't find (unless I missed it) and in the e2000 on how documentation set sizes of frame of reference.  Is that supported?  If so, what are the steps?

  A fact important is jumbo frames are not compatible at a speed lower than 1000 Mbps

  I think that Linksys E2000 already has Gigabit Ethernet ports.

  And I think that you can change the size of the image on the properties of the Ethernet adapter if the card is a Gigabit Ethernet card.

• EqualLogic SAN and Jumbo frames

  I can't get the jumbo frames to work on our Equallogic PS6000.  We have the following configuration PS6000-> Dell PowerConnect 6248 (bunk)-> Windows 2008 Server.

  The network cards on the SAN has been set at 9000 MTU, ports on switches are set to MTU 9216 and the NIC on Server 2008 is fixed to 9014 with active RX & Tx flow control.

  When the server connects to the SAN, newspapers account connection iSCSI target to the initiator "172.21.X.X:3260, iqn.2001-05.com.equallogic:0-8a0906-xxxxxxxxxxx-23a001a955452af6-server1" ' 172.21.X.X:49156, iqn.1991 - 05.com.microsoft:server1' managed, using the length of the standard framework.

  When I ping the SAN of Server 2008 with a shitload of 8972 bytes, it works very well.

  C:\Users\system>ping 172.21.x.x f-l 8972
  Ping 172.21.x.x with 8972 bytes of data: reply from 172.21.x.x: bytes = 8972 times<1ms ttl="255" reply="" from="" 172.21.x.x:="" bytes="8972"><1ms ttl="255" reply="" from="" 172.21.x.x:="" bytes="8972"><1ms ttl="255" reply="" from="" 172.21.x.x:="" bytes="8972"><1ms ttl="">

  Why 8972?  Told that some genius on the internet.  Any help would be greatly appreciated.

  Well we got it to work.  On Server 2008, we have Broadcom and Intel network adapters.  For our tests, we were just using the Broadcom NIC.  Properties Advanced NETWORK adapter, we initially have the value package Jumbo 9014 and it did not work.  So, we opened the Broadcom Advanced Control Suite that came with the NIC and searched and found that there are two parameters that need to be addressed.  There is a jumbo packet definition which has been set at 9014, which is what we wanted it in the advanced NIC Properties.  There is another parameter, MTU, which can be seen on the advanced NIC Properties.  It has been set at 1500.  Once we define to 9000, frames jumbo started working.  We then uncabled Broadcom NIC and wired the card NETWORK Intel and the value of frames 9014 on advanced network adapter properties.  Once we have that frame has worked on this NETWORK adapter, no other measures were needed.  If it's working now.  Thanks to everyone for their help.

• Best practices of Jumbo frames

  Hello

  I'm looking to use a pair of N3048s in a branch, as the heart of the network and for iSCSI (connected to a new equallogic).

  If I understand correctly, you can set the jumbo frames on the basis of a single port so it must be enabled on all ports.

  Will this cause a problem with the LAN network (i.e. not an iSCSI storage) that none of the devices are configured to use frames?

  Bravo for any advice,

  Huw

  It will not cause any problems. Frames allows the switch works with larger packets. If the switch receives a smaller package, it will be the leash at this size and it transmits on. If a larger packet is sent to a device that cannot receive the biggest package, then the package will be broken down into smaller.

• Enabling Jumbo frames on VMXNET3 adapter in Windows Server 2012

  Hello everyone on the forums of wonderful Equallogic :)

  We have a PS4100X of the virtual computer running on vSphere 5.1 EQL. Everything works very well, and we are about to migrate a VM 2012 SQL our database. I did some research on the issue of whether we should allow the frames extended on the VMXNET3 adapter in the virtual machine.

  Reading this white paper, it seems there are large performance benefits to enable jumbo frames and a few other options in the NETWORK adapter settings:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20403565.aspx

  Just curious as to how other people and if they saw an improvement in performance. Someone at - he had experience with this?

  Thank you

  Lee

  Frames being good or bad, is highly dependent on the switching infrastructure.   If the switches do not manage flowcontrol and frames, then performance could be worse with frames enabled.

  If the switches are not on the list certified for EQL tables, I tend to start with the standard frames, get a baseline run, then try frames gradually and do things of course worsen.

  Extended frames may provide an advantage, he will never be a huge increase, but it improves the efficiency of the network and could reduce the overhead of the processor.    Which are not mandatory for EQL iSCSI environments.

  Please check best practices with document ESX.  That can really help to maximize your performance with storage EQL.

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601.aspx

  Kind regards

• cannot ping vmk2 on other servers with jumbo frames

  I had 3 servers esxi 5.1 configure each with 2 NICs vmk - vmk1, vmk2

  vmk1 is on fabA

  vmk2 is on fabB

  the chassis is connected to the FI and the FI, its goes directly to the heart of nexus 7 k. Frames is enabled on the core switches.

  I have CoS of vmotion gold and a Qos policy of gold with the default values shown.

  the problem is each esxi host, when I try to vmkping (vmkping s 8000 vmk1 or ip vmk2), the vmk2 of another esxi host, it does not. but the fact of vmk1.

  I checked my vmnic political and especially on fabB models and they are all set to 9000.

  any ideas here?

  I ping the host local esxi itself and vmk1 vmk2

  Tony,

  One of the things to keep in mind is that traffic of FI - A IF-E passes by the upstream layer 2 network site.  Make sure the LAN past what uplink you also have enabled jumbo frames.

  David

• Jumbo Frame (MTU) option is missing on vSwitch (vSphere Client)

  Hello.  We use ESXi 4.1 in our environment.  I'm going on my ESXi host configuration via vSphere Client, and found out that Jumbo Frame (MTU) is missing in the vSwitch.  That's what I expected, but the "NETWORK card" setting"section is missing.  Any of you had this problem?  Thank you.

  

  With ESXi 4.1 and versions earlier, you must configure several command line parameters, see for example http://kb.vmware.com/kb/1007654

  André

• Jumbo Frame on 1 Gig network

  Hello

  I'm using iSCSI based shared the storage configuration on the 1 Gig host connectivity, iSCSI, physical switch software and storage.

  Should I enable the jumbo frame on all devices of connection in order to have a higher flow rate?

  It will cause no problem as the connection to the store of data or something like that?

  Kind regards

  Sushil

  Allow executives to Jumbro for the IP storage is recommended, in any case may be a glance on the following link to see a few considerations and test results on the Jumbo Frames: Jumbo Frames comparison test with storage over IP and vMotion & raquo; boche.net & #8211; VMware vEvangelist

• Jumbo frames, change the MTU size without VM guest tension

  I'm trying to disable jumbo frames, specifically to change the size of the mtu to 1500 (instead of 9000) in vcenter on some hosts. Some hosts run esxi 4.1, others are running esxi 5.0. I wonder if it is absolutely necessary to turn off the virtual machines that are connected to the iscsi san network while making this change, or is it relatively safe to make this change, while VMS are running.

  Each VM has active multipathing, 2 vswitches with 1 NIC associated with each.

  I know how to make the changes, regarding my questions whether it is possible to safely make changes while VMS still access the SAN.

  Yes, it is something that I do in my lab quite frequently without using maintenance mode. Memaad notes, maintenance mode is always preferable to avoid unnecessary risks, but it's finally to you.

  See you soon.

• question of vMotion iSCSI and jumbo frames

  Hello

  I have a cluster ESXi 4.1 using vCenter and a SAN MD3200i.  I'll do an upgrade to optimize the installation, which includes the installation of four NIC ports in hosts that will be used for iSCSI.  I struggle to enable frames or not, but if I do, I just want to do for the iSCSI, at least for now.  Currently, the maps iSCSI network on the hosts and the MD3200 iSCSI connections are connected to two switches separated, although I have seven other switches in the building connected to the PC, printers, etc.  What I only turn frames on two switches that iSCSI is connected, or do I have to enable frames on all my switches?  There is a Dell 2724 and eight 6224Ps of Dell.  ISCSI is connected to the 2724 and one from the 6224Ps.

  The two switches that are connected to the iSCSI ports are not dedicated iSCSI switches; they have other devices on them, but I can only enable the frames extended globally on the switch.  Would there be any problem allowing the frames extended on the switches, otherwise all connected devices are configured for them?

  Another question about vMotion: I will create four ports on each host for iSCSI vmkernel.  Currently, there is also a port configuration vmkernel for traffic management and vMotion.  Is it possible to set up each of the four iSCSI for vMotion vmkernel channels, or should I leave it configured on the port of vmkernel management?

  Thank you!

  Sure. If you're going to enable Jumbo frames, you need to have dedicated switches for that, or a switch that may have different units MTU on their ports.

• ESXi 5 and Jumbo frames

  What is the proper way to configure some jumbo frames for an ESXi cluster used shared storage NetApp?  Configure extended frames to the bottom of the VM Guest NETWORK card or I stop at the dvSwitch?  I already configure jumbo images throughout the storage on the physical hardware.  It's just the virtual machine where I'm not sure and if I do not set up the virtual machine, will there be problems?

  Thank you!!

  Then, you don't need to do anything for the virtual machines.

• No on free ESXi 4.1 jumbo frames?

  Hello

  I'm testing a Dell R710 connected to a SAN, iSCSI and Dell MD3200i according to the documentation, I find that I am out of luck if I want jumbo frames because it must be configured using the CLI tool, and this tool is not usable without having to buy a license. Is this correct, that I need at least the package Essentials to use CLI and therefore the frames?

  Thank you

  This is the API vCLI,... which is limited read-only in the free version. However, you can connect to the console (or ssh) directly to execute the necessary commands.

  André

• vMotion and Jumbo frames

  Enabling Jumbo frames ever advantage vMotion traffic bad? We will migrate out of our HP EVA on Netapp Storage soon. Currently, we are a single Fibre Channel shop now, but consider using NFS on Netapp only to align virtual machines (recommendation of Netapp Professional Services to increase the speed of the mbralign of a Linux VM).

  As we will only use really based on IP storage for the storage of virtual machine production, someone suggests to go even bother to change the size of the MTU on our switches and virtual switches?

  We are currently using 4.0U1 ESX and vCenter 4.0U1 but will be upgrading to 4.1 ASAP.

  I have never heard or read something about enabling Jumbo frames for vMotion. I don't think it's even a supported configuration.

  There are docs on activation of traffic iSCSI Jumbo frames. Most say, there is no advantage to 1 GBit networks but a significant advantage for 10 Gbps networks.

  André