How to query and make general dashboards with BSO cubes
Hello community,
Does anyone have the General information on how to make dashboards and repository with bso cubes. We did some dashboards with a few cubes of aso, but we know not even how do data appear in an analysis with bso cubes. We really don't know a lot about the difference between these types of cubes. Help demo or resources would be appreciated.
Thank you!
Hello
If you have managed to do with a cube ASO just do the same.
The ASO or OSB cubes in the end are cubes...
The different main, that's how you build your cubes as they probably contains different things with different structures.
Remember that ASO cubic automagically total when you query it, a BSO cube does almost nothing in itself, so if you don't calculate it you have generally not all aggregates, etc.
If you failed to get the data of your OSB the question is probably more your cube itself: there data? is it calculated? (if you are using SmartView you something?) you model right? etc.
Tags: Business Intelligence
Similar Questions
-
How to group and summarize the values with a vertical drop of 100?
Dear gurus
How to group and summarize the values with a vertical drop of 100 as the data indicated below:
Cas_Cod_ Cas_Amt_ Description
300 1000A
301 200 B
302 350 C
400 500 A
401 100 B
402 25
Now the data should be grouped like this
A (300,400) = 1500
(301,401) B = 300
C (302,402) = 375
Make sure that I don't have a column as description in my table to group data on description, its here just to give u an example.Hello
using mod for hundreds:
with x as ( select 300 code, 1000 amt, 'A' descr from dual union all select 301 code, 200 amt, 'B' descr from dual union all select 302 code, 350 amt, 'C' descr from dual union all select 400 code, 500 amt, 'A' descr from dual union all select 401 code, 100 amt, 'B' descr from dual union all select 402 code, 25 amt, 'C' descr from dual ) select mod(code,100) code, sum (amt) from x group by mod(code,100);
Using the mod you get the rest of a division, so mod (300,100) = 0, mod (301,100) = 1, etc.
Herald tiomela
http://htendam.WordPress.com -
How to edit and make changes to a scanned document
How to edit and make changes to a scanned using the adobe reader software
Hi micholef50672966,
Adobe Reader does not allow editing files - it allows you to view and comment on PDF files.
What format is the file that you want to change? If it's a PDF file, you can use Acrobat to edit (and convert any text image into editable text). If you do not have Acrobat, we invite you to try. You can download a 30 day trial of http://www.adobe.com/products/acrobat.html.
Best,
Sara
-
How to query the data of Contact with multiple fields
How can I query the data of Contact with multiple fields?
For example, I'll get contacts which are changed after a point at the specified time and whose country is US. How could I make the chain of research of the SOAP API "Query"?
And I also want to know how to make a search term for RESTful API for contacts above.
Any suggestions?
Thank you.
Hi Biao,
The following document describes how query for multiple fields using the SOAP API: request a Contact from several fields.
And you can search multiple fields using the REST API with the & operator. For example, to search for a Contact by e-mail address and date of creation:
- " emailAddress ='[email protected]' & converted > = '1369828886'".
Hope this helps and please let us know if you need more information.
Thank you
Fred
-
How to display BI Publisher reporting dashboard with a quick dash common to all BEEP reports
Hi gurus,
My version of BI Publisher is 11.1.1.12.
I have 10 BI Publisher reports, all have common guests.
I want to place every 10 BI publisher dashboard analytic reports and all reports BI Publisher must be invited to dash quickly. (Start date and end date)
For Ex: We have the start date end date guests and common to all BI Publisher reports.
How do we build this type of dashboard?
Please suggest.
Thank you
Kathia
I think I understand: you want to put all 10 BEEP reports one by one on the same page of dashboard.
If so, create two new guests of dashboard for the start and end dates and make them as text type.
In the variable of the presentation, you must provide your name of setting BEEP also exactly as it is defined in the BEEP data model, which will open a link between the BEEP and OBIEE.
Once done, you can drag and drop your guest of dashboard as a first leg on your dashboard page.
-
How warns 'space' error, make a backup with veeam?
Hello everyone.
I have a 300 GB virtual machine in a shop 305 GB data, so there are only 5 GB free. I use as backup Veeam software. Its working directory is another store of data with 300 + GB free.
I thought that have 5 GB of free space in the data of the VM store was enough for configuration files and such things, but maybe I was mistaken. The problem happened when I found the following error last Monday:
http://Msg.hbacommon.outOfSpace There is no more space for disk virtual myvm - 000001.vmdk. You
01:00:34.073 nov 21: vcpu-0 | may be able to continue this session by freeing disk space on
01:00:34.073 nov 21: vcpu-0 | the relevant partition and click Retry. Otherwise,.
01:00:34.073 nov 21: vcpu-0 | Click Cancel to end this session.
Take a look at the logs, it seems that Veeam just a snapshot, but in the same data store the virtual machine, not in the working directory of the virtual machine condfigured, where there is more than enough free space.
Why this snapshot was created in the virtual machine datastored when its working directory is set to be in the other data store?
22:00:06.912 Nov 20: vmx | SnapshotVMX done with snapshot "Snapshot TEMPORARY veeam BACKUP": 27
22:00:06.912 Nov 20: vmx | VIX: : VMAutomationCreateSnapshotCallback: CreateSnapshot Got recall, snapshotErr = 0, UID = 27
22:00:07.241 Nov 20: 1 vcpu. HBACommon: first write on scsi0:0.fileName='/vmfs/volumes/4beada54-cca8b737-8c6c-f4ce46bcaa39/myvm_1/myvm-000001.vmdk'
22:00:07.347 Nov 20: 1 vcpu. STRING DISKLIB: UpdateContentID: old = 0x1c0a9282 new = 0x7c25aa6d
22:00:07.347 Nov 20: 1 vcpu. DISKLIB-DDB: "longContentID" = "e605c5b301ba16c949cc573c7c25aa6d" (was "15037ad78fd1b288bd4bceba1c0a9282")
22:00:07.437 Nov 20: 1 vcpu. STRING DISKLIB: UpdateContentID: update of content long IDs
01:00:34.070 nov 21: vcpu-0 | Msg_Question:
01:00:34.073 nov 21: vcpu-0 | http://Msg.hbacommon.outOfSpace There is no more space for disk virtual myvm - 000001.vmdk. You
01:00:34.073 nov 21: vcpu-0 | may be able to continue this session by freeing disk space on
01:00:34.073 nov 21: vcpu-0 | the relevant partition and click Retry. Otherwise,.
01:00:34.073 nov 21: vcpu-0 | Click Cancel to end this session.
01:00:34.073 nov 21: vcpu-0 | -
How can we prevent this happening?
Thanks in advance,
Lorena
Welcome to the community,
If you can confirm that the snapshot is created in the location workingdir when you take a snapshot manually, you must open a call with Veeam. Otherwise, check the settings (http://kb.vmware.com/kb/1002929) and make sure that the virtual machine is charged to the inventory after changing the vmx file.
André
-
Outlook Express broke down. With Windows XP SP3 can get detailed instructions on how to uninstall and reinstall Outlook with original disc?
OE gives an error message standard it is not correctly installed. Its a remnant message from OE4 and is false. You probably corruption with folders.dbx and you should remove it. See www.oehelp.com/OETips.aspx#7 then, after departures OE you must back up your messages and given the corruption, go to file | Identities and setup a new identity for you give a fresh message store and then you can use file | Import | Messages to bring them from the old identity.
Steve
-
How to stop and restart a measurement with specific criteria?
Hey guys,.
I burn my brain trying to figure this problem on my program.
For my research project, I use an O2 sensor which is coupled to a Labjack U12 card and that's why I make a value of 4 mg/L, based on the switch to an electric socket (connected to the analog output) that is connected to the ventilation system. So when I 3.8 mg/L lights aeration and 4,2 turns off.
But I want to execute this measure for some time (maybe 10 minutes) and then stop the signal at the analogue output. After awhile the O2 measure will be reduced to values of 0 mg/L, but I want that when it reaches a specific value (perhaps 0.5 mg/L), is always idle for some time (maybe 2 min) and then again activates the signal at the analogue output (reboot cycle).
Is it possible to was this concept using Dasylab? I would be very grateful if you could help me with this!
I enclose 2 photos, the real configuration of my block Dasylab and the other is the extent expected after the new configuration.
Hugs and Outlook for the suggestions.
Celso
Is the curve in the diagram of the output of the "Labjack: AI"-module?
You can then use the following series of blocks:
Direct the signal of the Labjack-block in a block-combitrigger: Start-event is when the signal is less than 0.5, Stop-event is when the value exceeds 0.5 (do NOT use events "is less to ' / ' exceeds '!).
Connect the trigger block to a block Counter, which counts both the signal received (from the trigger-block) is TTL-high.
Use another trigger-block just after the block Counter: beginning-event is when the signal exceeds {insert time in seconds}, Stop-event is "live".
Now connect a block action, which controls the ventilation switch corresponding (light: curve rises, turn off: curve drops - is this correct?), the action should be triggered, if the signal of the previous block put on a rising.
How to control the measurement time of 10 min with meter,-relaxation, switch-action-modules and is left as work at home.
-
HOW TO install and make CCP in Jdeveloper 12 c
Hello experts, I am new to Jdeveloper.I uses Oracle weblogic server10.3.5 with oracle forms and reports 11g to windows 7 my weblogic is configured for oracle forms and it works well. Now, I want to install Jdeveloper 12 c to make CCP components to my oracle forms. Please tell me the tips to install jdeveloper 12 c in my system so that I could use my oracle and reports forms and Jdeveloper.For that I should install jdeveloper with separate weblogic server. Please tell me that how can I do for my PJC oracle forms. Thank you cordially Abdellatif.
I solved this problem
-
For a long time my address bar is backwards, the triangle button (I guess it's called the location bar history or something) always showed my most visited Web sites in a big box with all my sites. Now it always does the same thing but the window its shorter and has now a scroll bar on it, is there a way to restore or change this option to how I got it?
Normally, you should see approximately 12 items in the drop-down list.
This is defined via the pref browser.urlbar.maxRichResults you can review and edit the topic: config page.
If you see a lot less you could have an extension or a theme problem.Start Firefox in Safe Mode to check if one of the extensions (Firefox, Tools/menu key > Modules > Extensions) or if hardware acceleration is the cause of the problem.
- Put yourself in the DEFAULT theme: Firefox, Tools/menu key > Modules > appearance
- Do NOT click on the reset button on the startup window Mode safe
-
How to add and schedule a workout with Apple Watch?
I have a Garmin watch and I can easily create a restructuring plan (of the web database) and transfer it to the watch. My training is a series of market, slow and fast running at different times during the workout. Anyone know if I can do the same thing with the Apple Watch? Thank you!
You will find here how to customize your workout on Apple Watch use the app to your Apple Watch - Apple Support training
-
How to stop and restart a .vi with a button front?
Hey guys, a newbie here.
I have a .vi with a stacked sequence. First frames are few parameters (LIN master node) and initialization of hardware and hardware data should pass on (the frame response table). In the next section, there is a loop in which the data of sends and receives material (LIN monitor). If I want to change the initialization, settings, or data values, I need to stop the .vi and restart it. I was wondering if there is a simple way to do this with a single click (a button on the front panel).
An alternative would be to put another loop outiside all stacked sequence, then run it once with a push of a button (the inner loop should leave the reboot on the outside), is it possible?
I hope I made any sense. Thanks for your suggestions.
Tomaz
Ideally, redo the code with a state machine would be the best way to go, if this is so you can add this powerful tool to your Toolbox. That being said, wrapping your existing code in a while work loop, with its own stop button to stop the program, if the execution of the entire sequence is ok. Where you might encounter problems with this, is if there is a step in the sequence that should not be run again, there should be the encapsulation of code from the image of this sequence in a case statement that only runs the first time through. If you have the time, learn how to use a state machine would be a real advantage, really take your LabVIEW knowledge to the next step, if you pardon the pun.
-
How to print and scan in xp with on the installation of office 2000
Hello
I removed office 2000 proffesional and it deleted the program printing and scanning. Do you know if there is a separate program from microsoft or how I can install just part of the office.
Thank you
Jeff
Hi Jeff,
To provide the proper resolution, I would need more information on your side.
1. What is the number of brand and model of the printer and scanner?
2. what program you were using before you print and scan?
I suggest to try the procedure described in the article and check if it contributes to printing and scanning.
Use your computer to print, scan, fax
http://Windows.Microsoft.com/en-in/Windows-XP/help/Setup/print-scan-faxHope this information helps. Answer the post with an up-to-date issue report to help you further.
-
How apps, downloads and slips are included with the DPS company?
How many unique applications, folios (not entirely sure that I understand multifolios vs folios) and app downloads are included with DPS company each year?
Ah, sorry! My mistake completely. We have updated our pricing model, and you are quoted is based on the new model. Your sales representative is to give you accurate information and is the right person to ask these questions to.
Neil
-
How to find and change in InDesign with GREP?
Hello
I'm working on Indesing with 100 + page at the same time and in this case use 'find & change' option for faster work. I found an application for "GREP" [find what: (\d)([\|\u]) | [() [\|\u]) (\d)) ] who find them number with character and the character with numbers. see in the picture below...
Now, I want to change "GREP" code to add a sixth space in bwtween figures with the character and the character to the number. For more details, see photo below...
can any buddy help it at the same time & the same query?
Try the thius on a copy of the file, because it can have unintended consequences:
Find \d(?=\u)|\u(?=\d)
Replace $0 ~ %
Maybe you are looking for
-
I have can´t open my photo app, it just says: "library of closing". What can I do to fix my problem and review my photos?
-
Whenever I start Firefox the boring "Hooray!" "Your Firefox is updated" screen/tab is displayed. I know that it is up-to-date. How can I stop this?
-
Hacked account - need of my entry date to contact customer service
Does anyone know how to do this? He drives me crazy - I had my Skype account for years, I have no idea when I registered. All information concerning this problem for Windows :/
-
I have a HP Mini and I get password control failed... Fatal error... System stopped... CNU92262D5. Can someone tell me please how to unlock this computer? Thank you
-
HP Pavilion Notebook - 15-ab04: some keys on the keyboard does not
Hello Recently I'm impossible to insert the exclamation mark (SHIFT + 1) on all programs. I know there is no problem with keys like shift key works and the number 1 button also works. But when I press these two keys in combination that I get nothing