How to re-enable Lightroom after losing during the clean install of windows

Similar Questions

• After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive.

  * Original title: hard drive

  I have a lenovo laptop, processor Intel i3, 500 GB hard drive. After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive. I ran chkdsk looking for bad sector and its display 6000 KB in bad sectors. After completing the audit when it began to restart its stuck when the windows logo appears. What should I do? Reinstall the windows help?

  Run the hard drive HD diagnosis extended CD scan manufacturer to know with certainty the State of the reader.  If your brand has no bootable diagnostics in the link, use Seagate Seatools burned onto CD or SeaTools for a USB key .  Follow this with a full check disk command from the installation media kicked prompt know with absolute certainty the State of the reader.  If he repeated the errors after you run the two tests twice, I replace it or at least keep everything backed up in real time.

  If by chance the drive past diagnosis then compares the steps you've done with the best possible Clean install Windows 10 in the link, you can do more if it varied too - especially if the partitions were not deleted during install.  If you do then I additonally run own Diskpart command command line of the punt media accessible to the first screen after startup by pressing SHIFT + F10 keys, or through the repair your computer on the second screen.

• How to uninstall Windows 7 32 bit or get the clean install of Windows 7 64 bit to work properly.

  Today, I bought and installed windows 7 32 bit as an upgrade from vista 32-bit, shortly after I spoke to my friend and he told me that I could have used the disk for 64-bit and Windows 7 64 bit instead, the problem now is that I can't find a way to remove windows 7 32 bits using other methods I've seen here as the file Windows.old, it isn't here. Also I cannot perform a clean Windows 7 32-bit to windows 7 64 bit installation because when I insert the disk it says that I need to boot from the disk, so I tried then whenever he says failed to load. IM fine with doing a clean install and losing what I have, because I have them the settings and files saved externally already so no need to save again.

  Thank you very much

  Mango

  Looks like you're stuck with a clean install of Vista's original support for start.

  Messages rating helps other users

  Mark L. Ferguson MS - MVP

• Satellite L650 - unable to connect to the internet after the clean install of Windows 7

  Hi guys

  IM really angry because I just finished installing a new copy of w7 on my laptop (upgrade home pemium to proffesional) and now the ONLY way I can connect to the internet is via a usb device.

  I even tried ethernet and no luck.
  The screen display resolution is also mucked up.
  What can I do?

  Also reset it to factory settings make me reinstall it home premium?
  If so I'll do that but I need to know if this is the case, please

  its a PSK1JE L650 btw

  Post edited by: bilal98

  > I tried Ethernet and no luck.
  > The screen resolution is also mucked up.
  > What can I do?

  You must install the necessary drivers.
  For internet connection, you will need to install the LAN and WLan driver.
  To get the best display resolution install display driver

  > Also reseting it to the factory settings let me reinstall it home premium?
  > If so I'll do that but I need to know if it does, thank you

  Looks like you have already done this as posted here:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=68031

• Removal of the reserve system and PQSERVICE during the clean reinstall of Windows 7

  IM about to format my hard drive and reinstall Windows 7 using the windows 7 CD that I bought. I see a number of partitions:

  Disk 0 partition 1: PQSERVICE

  Disk 0 partition 2: System reserves

  Disk 0 partition 3: Acer

  Disk 0 partition 4: DATA

  I would like to reinstall also costs as possible

  Can I delete Disk 0 Partition 1: PQSERVICE and Disk 0 partition 2: RESERVE SYSTEM

  I think PQSERVICE provides stuff like the drivers for my ACER desktop computer requires. However I already downloaded the ACER site using my serial number. I'm more concerned about the reserve of the system parition.

  I got response would be much appreciated. I'm not to make a terrible mistake.

  Thank you

  your PC had no any CD to re - install because it is inside the PQSERVICE partition, you must make the CD yourself using Acer erecovery tool.

  without PQSERVICE and create this partition with Acer erecovery CD/DVDs you will not be able to restore factory default.

  If you don't want or need it, simply clear all the HARD drive and go with a simple installation of windows 7, PQSERVICE and system restore are not needed, the system restore is not created from the new facility.

  The drivers are downloadable as you have already found.

• How to eject a disc after download in the new lightroom?

  Am I missing something or is part of this feature? How to eject a disc after download in the new lightroom?

  There will be an another upcoming update for Lightroom, where import old windows will be restored and eject option was part of it.

  So we can just wait for the next version of the eject option restores also as well as the import window.

  Really, thank you for patience on this and apologize for the inconvenience caused to you.

  Thank you

  ~ Mohit

• How can I enable AHCI in dv7 6199us? And install windows on a SSD?

  Hello!

  I got help.

  How can I enable AHCI in dv7 6199us? And install windows on a SSD?

  Intel based computers, like yours, are usually set to "RAID", which is a superset of "AHCI". Basically, if the BIOS won't let you choose between "IDE mode", "AHCI" and "RAID", leaving in the RAID led to you everything done "AHCI". In this case there is no need to activate the AHCI, as RAID will support an SSD anyway.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• screen turned sideways during the cleaning of the keys. Look in the event viewer shows no case... How to rotate screen?

  How to rotate screen? turned on its side during the cleaning of the keys... difficult to use the cursor or anything else because everything is under tension.

  Press Ctrl & Alt keys and use the arrows to rotate back.
   
  According to the graphics card on your computer, these can be alternatives.
   
  Right click on the desktop | Graphics options | Rotation.
   
  Right click on the desktop | Screen resolution | Orientation.
   

• How to remove a schema after having connected the expdp session

  Dear Experts,

  How to remove a schema after you connect the expdp session?

  I'm not able to reach a work

  
  [oracle@orcl28 ~]$ expdp system/****  attach=SYS_EXPORT_SCHEMA_01
  
  
  Export: Release 12.1.0.1.0 - Production on Mon Jan 18 02:23:26 2016
  
  
  Copyright (c) 1982, 2013, Oracle and/or its affiliates.  All rights reserved.
  
  
  Connected to: Oracle Database 12c Release 12.1.0.1.0 - 64bit Production
  ORA-39002: invalid operation
  ORA-39000: bad dump file specification
  ORA-31640: unable to open dump file "/home/oracle/datapump/UREPJ.dmp" for read
  ORA-27037: unable to obtain file status
  Linux-x86_64 Error: 2: No such file or directory
  Additional information: 3
  

  You have this table in the schema of SYSTEM-SYS_EXPORT_SCHEMA_01?

  Delete this table, and then try again.

  Aman...

• How can I make my PC OS meets the requirements and get windows vista to be taken in charge for the installation of adobe lightroom 6?

  How can I make my PC OS meets the requirements and get windows vista to be taken in charge for the installation of adobe lightroom 6?

  Well, I'm not really sure of Windows Vista.

  You can contact customer service for additional troubleshooting.

• After a clean install of Windows Vista, Intel Wifi card is installed and activated, but does not detect the network.

  Wireless card not working after a clean install of Windows Vista

  I did a clean install of Windows Vista Home Premium on my HP Pavilion of 32 bits. I've completely updated Windows via Service Pack 2. Given that the clean install, my wireless card, Intel (r) Wireless WiFi Link 4965AGN, was not able to detect all the networks. The Wifi card is listed under NICs as being installed and activated. the hardware on my laptop Wifi switch is set on "on" and the light is blue, indicating that the card is working.

  I can connect to the internet if I connect physically my computer to the modem with an ethernet cable wireless, so the modem isn't the problem. Other computers can connect to the wireless modem, so my Wifi modem functionality is not the problem. The problem with my computer.

  I tried to uninstall the Intel driver and reboot my computer with the generic driver. Install the driver generic, but my wireless card has not always worked. I then ran an update of windows, nothing helps.

  I tried to install the "Intel® PRO /? Wireless and WiFi Link"drivers for Windows Vista (32-bit 13.1.1.1 the latest version and the previous version 12.4.4.5 32-bit) for the Intel® Wireless WiFi Link 4965AGN directly from the Intel Web site at http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+WiFi+Products&ProductProduct=Intel%C2%AE+Wireless+WiFi+Link+4965AGN. The map didn't always work with a driver.

  In addition to the pilots, I also downloaded a tool of diagnosis of Intel (Intel® PROSet /?) Utility of WiFi wireless connection for Windows Vista 32 -? Bit). Said diagnostic tool the WiFi card is not installed or enabled, however, Device Manager maintains that he is also installed and active.

  Is there a problem that causes Device Manager to say that all is well with the card, but does not map to realize that they diminish the radio signals? Everything's fine, diagnostic, it just does not detect networks around him. Help, please.

  Hello

  The on/off switch actually works?

  Since it is an internal adapter to ensure it is enabled in the settings of configuration/F2 (BIOS/CMOS) often like you
  Start - so look at the screen.

  Have you tried the computer on other WiFi networks? You had a WiFi type problem before the
  Re-install of Vista?

  ---------------------------------------------------------------------------------------------------------------------

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• New R13 - R7 - 372T: Tools missing after the clean install

  Hello!

  I got my R13 - R7 - 372T today and I want to do a clean install of Windows 10. I checked the Acer site and saw that most of the drivers are available on the download page, I also found the abApps (Portal of Acer and) download ( https://www.cloud.acer.com/ops/downloads) where I need those who one day but its seems that some of the pre-installed tools/applications are missing. How can I reinstall the following tools if I wipe my device? (I have already created a backup of the recovery partition but I need regular installation files):

  -Acer care center (edit: I found a link for verification of compatibility to download it here: http://www.acer.com/ac/en/MY/content/software-acer-care-center )

  -Acer Hover access (edit: found the link for flight stationary access here: http://go.acer.com/?id=18022#_ga=1.267060686.114307318.1458377954 but not sure of the version)

  -Dolby X 2 Audio Windows App

  -Acer Audio utility invert (makes that actually do?)

  I'm a little disappointed that Acer does not offer those by convenient download as the rest of the drivers and application of quick access for example. So where can I download those, or how I at least check out them of the recovery media that I created?

  Edit: Looks like after some experiences of most of the tools I mentioned is unnecessary (so I removed them from the list) or available by searching around for a while. However the 2 above mentioned utilities are still missing.

  Thank you!

  Alex

  Dolby

  Go to Manager of device/Audio inputs and outputs / RealTek High Definition Audio speakers / right click and uninstall.

  Go to C:/drivers/setup and install. Otherwise it

  Audio

  Realtek

  Audio driver

  6.0.1.7288

  386,0 MB

  04/11/2014

  Download

  Don't restart yet.

  Go to PCEE4/Dolby Home Theater / double click and install/reboot.

  Audio Acer utility to invert

  I don't know what it is. Nobody seems to know.

• How can I save my messages instand from the Webcam live messenger window

  How can I save my messages instand from the Webcam live messenger window

  Hello

  I hope that's what you're after...

  http://www.WikiHow.com/save-your-Windows-Live-Messenger-conversation-history

  Concerning

  GT4U

• Computer froze during the upgrade/installation of windows xp

  I have windows xp home edition on a Dell desktop computer. I had problems with the computer freezing and then lost the connection to the internet 3 days ago. So I decided to reinstall windows xp from cd. However, I have chosen upgrade, rather than new install (because it was the suggested method). Now my computer will not complete the upgrade but is frozen during the installation. It remains to 32 minutes until the end. I can't seem to start, can't control/alt/delete or whatever it is. If I unplug my computer and launch it then again once, it resumes where it left off. How can I break out of this loop and start over with a fresh install? Thank you.

  OK, it would have been better to have all the information on this machine in one place. I guess your question in the other post you made about activation is for the same computer? If this is correct, then the information I gave you in your previous post is not applicable.

  With Dell computers, using Dell reinstallation media, you don't need to enter a product key during installation and the operating system is already activated.

  If you use a different XP installation disc that was not provided by Dell, this is why you are experiencing activation problems. If you do not have a Dell brand installation CD, you will need to use a manufacturer OEM generic system disk and use the product key on the label of CA certificate on your computer. If you use a copy of XP retail, you would use the product key on the CD to copy the retail case. In the case of the generic OEM drive, it must be the same version of XP that came with your computer (Home/Pro/MCE).

  All that being said, your sound of questions as a material. Did you leave all devices attached during the repair facility? If so, this can also cause the problem. Unplug everything except (obviously) your mouse and your keyboard when doing an operating system install. You should ensure that the material is solid before attempting to install again.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  Understand that all your data will be lost. If you save before, try to start with Linux Livecd such as Knoppix and copy the files to an external hard drive. Then download a utility from drive to drive mftr site. or use a third-party (Acronis Disk Director, Knoppix gparted) start Disk Manager to delete partitions on your hard drive and format the drive.

  Now, do a clean install of Windows, preferably using a Dell XP installation CD. Install Dell drivers for all your hardware when you're done, restore data from backups. MS - MVP - Elephant Boy computers - don't panic!

• How to do a clean install of Windows 7 Professional of a DVD on the ProBook s 4530?

  So I have Windows 7 Home Premium 64 - bit installed on my laptop and I want to get rid of it completely and to do a clean install of Windows 7 Professional 64 bit from a DVD.
  I don't want to use windows anytime upgrade somehow! Because I have a few serious bugs with my current installation and a clean install, I can be sure to get rid of them

  I'd appreciate if someone could tell me how exactly to do this and if all my data will be deleted. If so, will it download all drivers HP and the software again by myself? :/

  roby1324 wrote:

  Bugs are not serious but they affect several programs and it is impossible to use my laptop, I was doing.
  And no, I have no recovery option, I don't have any dvd with my laptop, or something like that and personally I didn't do all the backups. Which was a mistake that I won't repeat.
  In addition, because of my college, I get a free copy of win 7 professional so why not use it?
  I have already burned on a DVD, now I just need to detail how a facility own n_n
  So after I installed win 7 Professional I just copy and replace Driverstore and C:\WINDOWS\SYSTEM32\DRVSTORE instead of download the drivers?
  BTW, I'll accept your next answer as the snap

  You will use the copied Driverstore and C:\WINDOWS\SYSTEM32\DRVSTORE for is the source of the drivers when you then. Do not replace the folder in the new installation of Windows with the folder that you copied from the initial installation of Windows. It would not be a good idea.

  Once you have done the copy of the file and have it practice you can simply put the installation DVD into the DVD drive and boot from it. There will be a point where asks you if you want to save your previous installation. Say no to it.

  At this stage you can always do a defined recovery disk. I recommend that you do this. This is the copy of the operating system and drivers you purcased your PC with. If you do not want is not a problem like UO can always buy it at HP over the next years.

  Best regards

  ERICO