How to repair severely damaged damaged audio?

I have some terrible with audio images (because of the way it was recorded), for some reason the microphone settings were incorrect for a segment of the video and I found myself with a lot of background and minimal noise audio audible. Unfortunately, I can't save this video once again and I need to work with what I have. I have read all the help and tried in many ways with the Prime Minister and sounbooth for this problem (a noise print capture, etc.), but it is simply the worst sound audio (something that I didn't know that was possible).

I was wondering if someone can help me solve this audio, thanks!

Levels are quite low, and it looks like it's probably too noise AC. Fortunately, you have a récitante (here), so could get lucky with some EQ works in the range of 250 to 500 Hz. You should be able to eliminate some of that noise ambient, without affecting the Audio speaker many - listen very, very carefully, then slowly, adjust as a side effect of the noise reduction is a hollow, echoing sound, and with the tone of his voice, do not think that this would be desirable.

Without going through the open WAV, I can only guess, but here would be my intended workflow:

Noise reduction - first capture a sample of the first part of the Clip profile (before the speaker with only ambient noise) that you posted and then apply the noise reduction process. Start below the value default ~-7dB (think that's the default, but it has been so long I've seen failure, that, well, my memory could be faulty - or defaulty?) and work upward. Listen very closely for ECHO, I warn you.

Levels - I would look at Amplitude > amplify and probably around + 6 to + 9dB

EQ - we could approach things from two directions here. I probably watch Graphic EQ and work in the 250 Hz to 500 Hz range, with attenuation below ~ 120 Hz. Or, we can examine a Notch Filter, doing similar. Or a combination of both.

Low Pass - High Pass - probably a bit of both

Compression - multiband compressor

VST - DeEsser

Pitch Shifter - think think I would reduce his pitch, just a "skidgen" (very technical term means just enough, but probably not a lot...

Hearing is not THAT difficult to use program. However, it is extremely powerful, and tap into that power is another story completely. As I use it for Audio for my video, I must say that I am a 'beginner power. " I do a lot with it, but for a limited range of materials and operations. I have never scratched the surface of the potential, sound engineer would just take for granted. Yet, for what you need, I think that with the above mentioned tools and a lot of very attentive (good noise cancellation headphones are a must here), you can hit it pretty well.

Now, if you have Soundbooth, you have some of these tools, but don't think you have the noise reduction process, and it's a biggie.

Let me know how it goes and if you get stuck, don't hesitate to PM or email me: info AT huntphoto DOT com If you need for me to review the Audio, I can accept enough large attachments in e-mail, or you can use a service like YouSendIt. I'd be happy to give it a listen and try my hand and formatted it for you. I can take notes of what I do with the segment and those who share. If you like the result, it would be easy (yet critical listening), to just go down the steps.

Good luck

Hunt

PS - I see why reshooting isn't really an option, and dubbing of a speaker, who is a VP with Del Webb, probably isn't ideal, either I was hoping that you had a theatrical play and can hire just the actor/actress for an hour. So much for that idea.

Post edited by: Bill Hunt - added PS

Tags: Premiere

Similar Questions

  • How to repair a damaged system drm

    Hi im trying downloaded zune music and a few songs that I downloaded do not work it said I had to go to the microsoft support knowledge base for my response to a corrupt drm system but I have no idea.

    Help, please

    Doesn't inspire us the little info you give.
    How to ask a question:
    http://support.Microsoft.com/kb/555375

  • How to test water damage/spill? Minor IdeaPad Z510 water spill

    Hi all! I am a new Member, so please do not hesitate to correct and inform me of the mistakes that I can do on these forums!

    Today, the water was accidentally reversed on my keyboard and trackpad. It wasn't a lot of water but not bad. Water is set on the keyboard for maybe 5 seconds until I could wipe it (following a shock what to do). The water does not go through the keys at all. I immediately turned off the computer after it.

    My question is, now I'm on the laptop, all the keys and everything work properly, I don't notice any significant change in processing speed and all the ports work. How would check any damage of the waters of the oil spill? I've had this laptop ~ two months ago and certainly wouldn't return now since I have a lot work in progress. It is useful to send, how long still will take, it will be under warranty, if not how much will it cost?

    Thank you for anyone who reads this, or even attempts to answer one of my questions! This community of love!

    MakarovZachaev wrote:

    Hi all! I am a new Member, so please do not hesitate to correct and inform me of the mistakes that I can do on these forums!

    Today, the water was accidentally reversed on my keyboard and trackpad. It wasn't a lot of water but not bad. Water is set on the keyboard for maybe 5 seconds until I could wipe it (following a shock what to do). The water does not go through the keys at all. I immediately turned off the computer after it.

    My question is, now I'm on the laptop, all the keys and everything work properly, I don't notice any significant change in processing speed and all the ports work. How would check any damage of the waters of the oil spill? I've had this laptop ~ two months ago and certainly wouldn't return now since I have a lot work in progress. It is useful to send, how long still will take, it will be under warranty, if not how much will it cost?

    Thank you for anyone who reads this, or even attempts to answer one of my questions! This community of love!

    Am I in your shoes I would be first turns upside down the unit so that the KB's down. I would then blow hot air in the keys remotely using a hair blower/dryer. After that I will begin to open the unit to check further for everything SIP of water by. Blow the additional hot air to ensure that everything is dried up. After that, I'd start checking the AC adapter and the battery according to the recommended procedure in the hardware Maintenance Manual.

  • How to repair this error C:\Windows\System32\mscoree.dll__

    How to repair this error C:\Windows\System32\mscoree.dll

    Hello

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    If necessary:

    Mscoree.dll could not be found error resolution
    http://pcsupport.about.com/od/findbyerrormessage/a/mscoree-DLL-not-found-missing-error.htm

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • My mac had to be repaired several times and eventually I was forced to restart the entire computer, wiping everything.

    My mac had to be repaired several times and eventually I was forced to restart the entire computer, wiping everything. I registered my purchase CS6 Design Standard of two years, so I have the serial number, but I don't have the record of the initial purchase. How do we install CS6 on my practically new Mac?

    [Duplicate message deleted... post the same question more than once is confusing... MOD]

    ADDITION to previous versions http://www.adobe.com/downloads/other-downloads.html can help

  • my firefox browser does not load at all no matter what page but explore and google chrome. How to repair?

    my firefox browser does not load at all no matter what page but explore and google chrome. How to repair?

    Hello, these questions can also be caused by security/firewall software which does not correctly and therefore blocks updated versions of firefox: solve connection problems to websites after Firefox update

  • How to combine several libraries in a library complete?  And this new global all0 library can be an external hard drive?

    How to combine several libraries in a library complete?  And this new global all0 library can be an external hard drive?

    1. click here for more information.

    2. Yes, if this disk contains a partition image or the drive Mac OS Extended format.

    (142356)

  • I downloaded Firefox 4. The top of my page looks nothing like what they show. How to repair or return to the Firefox I had before. I can not even find anywhere on my computer to uninstall Firefox 4

    I downloaded Firefox 4 and it does not give me most of the tabs and that he said that I would get. The top of my page looks nothing like what they show. How to repair or return to the Firefox I had before. I can not even find anywhere on my computer to uninstall Firefox 4

    Windows XP does not display the default Firefox Button. If you want to see the Firefox button, go to view-> toolbars and uncheck the menu bar. (To return to the menu bar, press the ALT key to temporarily show - see what happened to the file, edit and view menus?).

    If you want to uninstall Firefox 4 you can do from the control panel "Add or remove programs". See Uninstall Firefox on your computer.

    To get Firefox 3.6 go here: http://www.mozilla.com/firefox/all-older.html and read install an older version of Firefox.

  • How to remove several Favorites in safari?

    Hi, I was wondering how to remove several Favorites in Safari because I accidentally added thousands of bookmarks.

    To remove several items in Favorites, I'll

    1. Select 'Edit bookmarks' in the menu 'Favorites '. -This shows real bookmark tree structure using the window in the current tab.
    2. View, you can click the triangle to the left of the sub folder name to expand / corrupts.
    3. Then select items to remove using the click, shift-click, or order, etc..
    4. Tap the DELETE key or select "Delete" from the menu "Edit".
    5. Repeat step 2 to 4 for all items you want to delete.

    In the bookmarks view, you can also use drag - move to reorder items.

    After cleaning, you can close the window/tab or just start normal web browsing in the same way as the other web site of switching.

  • FCP 7 How to display several takes both

    I'm running FCP 7 on a Macbook Pro with OS 10.10. Trying to figure out how to display several takes of the video on my calendar running at the same time. Mounting a show of live music from four cameras simultaneously turned and want to choose between shots while seeing the four outlets. Is this possible?

    Multiclip editing:

    https://documentation.Apple.com/en/FinalCutPro/UserManual/index.html#chapter=42% 26section = 12% 26tasks = true

    MtD

  • How to remove missing references and audio files or instruments that popup at launch I need is no longer?

    How to remove missing references and audio files or instruments that popup at launch I need is no longer?

    For audfio missing files: go to the Project Audio Bin, mouse control select unused , and then press DELETE. And then click Save.

    Missing instruments or plugins, go to your mixer and remove/Exchange any plugins that have a '!"in all of their slot. And then click Save.

  • How to get several beep?

    Hello

    I want to get several beeps output if a comparison condition gives output as true.

    Can someone tell me how to get several beep?

    Put the beep function in a loop with a small wait for the statement.

  • How to open the sounds and audio properties by using Labview

    Hi all

    How to open the sounds and audio properties of the control panel using the exe from system Labview vi.

    Y at - it all dll also open this property.

    If there is some dll which is which and how to program the dll to achieve my goal.

    Wow, you followed after a few...

    Open the command window is because to open the Control Panel, you need to execute it in the context of a shell, and it's what is done with the "cmd /c mmsys.cpl. To open the applet without using cmd you use RunDll32.exe, like this:

  • How to scan several documents into one PDF

    How to scan several documents into single PDF - have no ADF

    Thanks - great app

  • After you have reinstalled Windows XP my computer said that having no audio device. How to re-install a new audio device?

    After you have reinstalled Windows XP my computer said that having no audio device.  How to re-install a new audio device?

    A. Si you have the sound driver file install it normally

    or
    B. extract the files to a specified location
    go to Device Manager
    find the audio device with the yellow mark
    Right click and uninstall or update driver
    Select Advanced Setup
    the location of the file
    and follow the instructions

Maybe you are looking for

  • Cannot find TOSHIBA Web Camera application

    I tried to access my webcam but the shortcut was missing from my desk, and I can find is no longer in the list of programs. I checked Device Manager and it says that the webcam is working normally. However, I can only use it online.Any help would be

  • Photosmart 2710 and new Dell Computer problem

    Just got a new Dell XPS 630 and can not load or recognize the Photosmart 2710 all in one.  We have Dell install Windows XP Professional, but I wonder if they let Vista stuff out there.  Tried to use the CD supplied with the printer... no joy.  Also t

  • Extend the RAM for Flex 10

    Greeting, My computer laptop flex 10 has 2 GB of memory. It is possible to upgrade memory to 2 GB more to make the laptop more fast when I open any program?

  • hpg62-219wm

    How disconect and conect HDD

  • Vista - Error Codes: 8024200d & 80070490 (cannot install updates)

    Windows Update, specifically 4 updates. KB967723, KB970430, KB972145 KB981793, indicates updates important Dungeon trying same error keeps coming back. I even updated to service pack 2, just after that this updates always stayed tried again and again