I don't register

Similar Questions

• Satellite M300 with Win 7 64 don't register mouse bluetooth

  I have just updated my M300 to Win 7 64 and cannot get MS Bluetooth Notebook Mouse 5000 to sign up. I've updated the BIOS and drivers. Any suggestions would be welcome. It worked perfectly on this computer with Win 7 32.

  Thanks in advance.

  Akuma is right.
  You need Toshiba Bluetooth stack!

  Reinstall the battery of BT and activate BT using the FN + F8
  Notes; the FN + F8 control WLan too. You will need to press this combination of keys several times in order to get the BT active.

• My mouse double click sometimes, and sometimes don't register the click.

  I slam my finger down on the left click and it clicks then, otherwise not.
  Sometimes it will be a single click-double-click.
  Only occurs with a left click, right click is perfect.
  I checked the parameters of double click in the mouse settings.
  I reinstalled software for my Logitech LX7 optical mouse several times. Updated, nothing.
  He did this for about 3 months, then stopped for 2-3 weeks and returned as of today.
  The only thing I can think of that I did differently, was that I was not playing a video game in windowed mode. (w to find target) I played it in windowed mode for the first time for several weeks and now she's back. I stopped to play in windowed mode, and he has not disappeared.
  I reinstalled the driver for my mouse several times. Unplugged, he moved to a different usb port.
  It is not my mouse because she does it with my mouse trackball of factory too.

  I bought a new mouse. Problem solved.

• I have a photoshop cs4, but my computer crashed now, I reinstalled my win 7 again and photoshop cs4 is gone when I was installing it the serial number is no longer valid, I don't register my CS4

  has been reinstalled my cs4 because my computer crashed, but the serial number is no longer valid

  Have you purchased directly from Adobe or from an authorized dealer? If so, contact customer service .  Proof of purchase would be useful.

  If you bought it from a third party, Ebay or Craigslist, you may have received a serial number hacked or passed around that Adobe has taken and blacklisted.  Adobe will not help you.

  Why not buy Adobe software on eBay, Craigslist or Amazon Mkt | ProDesignTools

• CP1518ni color done correctly

  I have a CN1518ni color printer.

  I changed the toner cartridges when they ran out and with the new, the colors don't register on the right. The three colors come out off a hair or two and it's very difficult to read words.

  In any case to adjust color register?

  Thank you!!!

  Here's a link below which may help you.

  http://goo.GL/pEzdh

  Let me know if this is useful, thanks.

• The upgrade of my application fails (when it is registered with PhoneLogs)

  I use Desktop Manager to install/upgrade the java application, I am writing to you.  My application is configured to run automatically at startup function.

  1. when I just install my java application (which means that it is not on the device), it installs and works fine.

  2. when I update my application, the phone restarts, fails it application (IE not dΘmarre).  More clearly, if I go to the icon and click on it, nothing happens.

  3-if I delete the app, reboot the phone and install the application, it is very good (line with scenario 1 above).

  I narrowed down it to 1 line of code that makes the difference:

  PhoneLogs.getInstance () .addListener (myPhoneLogListener);

  If I don't register my app/process with the PhoneLog, upgrading the app has managed in all scenarios.  I guess that's because one of my 'myPhoneLogListener' objects is in the memory space of the PhoneLog at the time of the upgrade.  Also, my application is running at the time of the upgrade.  The application is still running in the background, intentionally.

  I would try an OTA update to see if it behaves differently, but I don't have any private location secure to host my app.

  How to make this upgrade work, without requiring the user to quit the application before the upgrade; given that I can't guarantee that users will do, and I don't have to have a bad experience with my application.

  I'm writing my own solution for others in the future.

  So before in my MAIN() method, I capture all the Exceptions and out in silence.  This was to avoid the dreaded AppError-200 during development.

  So I added a try/catch in my MAIN() to write all the Exceptions in the event on the device log, before to leave.  It turns out, I was getting a "ControlledAccessException.

  So, I decided to add a Thread.sleep (30000)-30 seconds before trying to run my problematic registration code.

  Good news and bad news, it worked.  But that tells me that there are a few occurring in race condition.  Well, I have no other choice.  I hope this helps someone else out there...

• Main features register or are not detected

  When in the AOL emails, about 1/3 of my key traits don't register.  The problem does not occur in the case of Word.  I changed the keyboard, but the problem persists.  The computer is a Pavilion a1600n running Windows XP. Any ideas?

  Hi RL47,

  You use AOL email in a browser (such as Internet Explorer, Mozilla Firefox, Apple Safari, Opera, Google Chrome, etc.)?

  If so, have you tried to switch to a different browser to see if the problem persists?

  If you use an application for AOL Mail, have you tried to reboot this request (uninstall/reinstall)?

  Have you tried setting out Microsoft Outlook / Outlook Express as email client (send and receive your AOL email using another application)?

  Given that the problem does not occur in Word, the material is fine, now it's cut just whether a number of web mail client or a browser problem.

  Please provide the above information and/or try the steps and let me know if you still experience the problem.

  Thank you!

• Wireless iMac mouse connects, titles, but order record clicks!

  My iMac went to sleep one night and the next mouse didn't is more only would record clicks.

  I realized the following without success:

  -changed the batteries in the mouse

  -restarted the computer (great for the Trackpad clicks). Mouse light is green, no still no clicks

  -reconnect the mouse (even the titles and physically clicks but clicks don't register)

  -guaranteed no other bluetooth devices is active in the region (except for the keyboard that works very well)

  -remove the mouse and reinstalled

  -turn off the trackpad and removed the batteries

  -stop of the iMac, unplugged for 30 seconds and restarted

  Mouse still fine and physically clicks but clicks do not register...

  10.11.5 OS

  Thanks for any help!

  Also tried a reset of the PRAM - no change

  I noticed that scrolling does not work on the mouse, but he still titles.  When I place the cursor on an object he comes on as usual but still no recognition of click.  Trackpad works fine...

  ??

• Synchronization with Serial read/write problems. can not get the functionality of the terminal emulator

  Hello

  I am writing a VI to control PWM with a microcontroller via a serial port. I wrote a simple code for the microcontroller that allows me to set the ratio of duty cycle on a scale of 0-65535. It works very well with Termite of Compuphase (RS-232 plug); The microcontroller invited me to an entry, expected that I would one, updates and expected another entry when I decided to send him. Now, I'm trying to get the same functionality on a LabVIEW vi but hit a snag.

  When I tried to send my orders with a series read base and an example of writing, everything worked fine. I could see the prompt entry, write an entry and if I was quick enough, check out the update message. Even when I was not fast enough, I was able to check the update by monitoring the PWM pin with a Logic Analyzer. The problem with the basic example, however, is that I need to update the report to aura cyclical ratio, so I went for an example of reading continues writing. The problem I've met; is that I have to switch between reading and writing to make it work. When I do that, either I don't hold write it down long enough and nothing happens, or I get several updates when I switch to reading. Some of these updates don't even match and produce updates to defective upgrades for example; 16000 16000, 16000, 16000, 6000, 600, 60, 16000, 1600, 60, 0, 0, 0, 16000, 60, 0, 0 etc.

  I tried which allows characters of endpoint in the hope that the writing would end at the end and go to reading where he would receive a termination character and wait for me allow writing once again, but nothing helped. I still have to alternate between the two and either get no response on reading several updates of variable accuracy. I tried to remove her allows read/write and their structures of matter in the hope that the loop flow, associated with the characters of endpoint would the case, but then the updates don't register at all. The funny thing is I did a VI like this before with an Arduino and that there not even no need to switch between writing and reading (I'm now using a Board of Freescale FRDM).

  I was also the frequency of timeout errors; Error-1073807339 at VISA Read, reason Possible: VISA Hex 0xBFFF0015. I removed the option to stop the while loop if there is an error so I can run but always pops up an error on the judgment occasionally. Could the problem of synchronization always cause me problems?

  Would appreciate all advice really, I am providing my slightly modified example screws and can provide the code for microcontroller on request, even if it's very simple.

  Thanks in advance, it is
  Yusif Nurizade

  In other words, frankly, a good bad example you according to your code. Also, you have the order of writing and read upside down in your amendment if the instrument requires a command to return something. It should really be using a structure of the event. The structure of the event around a write and read and use a value change event. I have attached a quick change. This mod is still a reading after writing. If necessary, you may have two separate events to write and read.

• structure of the event a substitute

  Hello everyone and sorry for what I think may be a very newbie question, but I can't understand not just how to use the structure of the event in my program.

  The presentation is as follows:

  I'm using labview for control devices in my lab.  I have to activate something for 30 minutes, then heat it for an another 30 miunutes (the first device is controlled DAQ and the second is controlled GPIB).  While these two processes occur, I monitor a temperature using the data acquisition card.  The two-step process is finished, I have to wait for the temperature to be lower at some point and then start again it.  So, I have to repeat this process for a number of times defined by the user.

  My question is this, I use a structure of the event to handle it all (this is maybe not the best way to do it, if you know a better way, feel free to share!).  The whole process of starting the program, I want to be able to stop it at any time in case something goes wrong, and I would do this by using a Boolean on the front panel, because I will finally control the process from a distance.  Is it possible to substitute a case of the event once it has started?  I have no doubt a 'Wait (ms)' VI in there somewhere to facilitate synchronization of processes, but once the VI begins the program waits until it is done before register you for any other button presses.

  Thanks in advance for any response,

  -daman

  You should definitely read up on State Machines!

  Maybe the link in my previous post doesn't work.  Try these.

  Reference design - http://zone.ni.com/devzone/cda/epd/p/id/6091

  State machines - http://zone.ni.com/devzone/cda/tut/p/id/3024

  ExpressionFlow Blog on policy - http://expressionflow.com/2007/10/01/labview-queued-state-machine-architecture/

  Machine States JKI - http://jkisoft.com/state-machine/

• Windows XP SP3 product activation key

  Original title: on the product windows xp3 key

  I have desktop dell for my roommate there wxp3 when I was downloading things he wanted on this subject, I do not remember seeing anything whether I don't register in 30 days windows stop well you stop I can't even in safe mode for recovery of the etc system.  When I go online after the entrance of seizure of the password of a message that I produced windows enable you want Yes or not I click Yes then place comes another spot by saying that the windows product activation is on x on ok to leave then nothing happens it keeps coming I chatted online on my pc with micro tech He said, I had to buy the Windows XP operating system to get the product key - what if I could do to get this work once I've done a system restore in SafeMode to April 23 nothing happens or I have to buy this wxpos on the money I can't spare ty for any help from maryanne

  [Moved from comments]

  MaryAnne,

  Have you contacted Dell for the product key?

  The product key sticker is usually stuck to the tower that provides to the customer of the OEM (Original equipment manufacturer).

  If nothing works, you may need to contact Microsoft Customer support to provide you with a new product key

• Action of browser ContentHandler

  Hello

  I recorded a Manager mime to run my application when a specific mime type is used.  It works very well and start my app when I click on a link in the browser that points to a local file of the type that I registered.  But when I click on a url pointing to the same file on a server (the server returns the correct mime type), he calls "save file...". "Save / Cancel.  He knows the mime type since if I don't register my app, it will ask "the selected item cannot be displayed...". ».

  So my question is how I do that instead of asking to save the file, it works directly similar app when it's a local file?  Should I introduce a certain action?  ACTION_OPEN is set for the opening of a local file.  I tried several other actions (run, install, new, save, select this option, send), but none seem to do the job.

  Thanks for your help,

  shabl

  The user must save the file before opening it in your application. There is no way around this prompt when using CHAP.

• Image showing strange problem

  Hello

  I am writing a Flex application and tries to display an image in a

  To load an image, I call the following code to a button's click event:

  myImage.source = "http://remote.server/file.png";

  This all works well except if I register a shot toward the bottom of the event in my main application handler.

  QNXApplication.qnxApplication.addEventListener (QNXApplicationEvent.SWIPE_DOWN, onApplicationSwipeDown);

  This seems weird to. Images loading properly if I don't register a listener for the SWIPE_DOWN, but as soon as I register the listener, I can not to display images.  If I just remove this line of code, images appear as expected.

  Has anyone seen something similar to this or any ideas what it could be?

  I'm developing a Flex application in FlashBuilder and try to run on the Simulator Playbook.

  I managed to solve the problem by removing the reference to qnx - air.swc I've had in the project.

  For some reason any pertaining to this seems to stop my app work.

• Third party software to be used as an endpoint

  Hello all, can anyone recommend a software (a free software is recommended) it can be used to record with VCS and express VCS. I need this software for test purposes. I also prefer if I can use this software as a standalone endpoint (without registration) to simulate incoming calls from the internet. Thank you.

  Video of Cisco's Jabber is free Internet version, which requires no TMS - just an internet connection.  You think "Cisco Jabber for Telepresence" which is in fact the 'corporate' of the same software version.

  Video of Jabber don't register with VCS, but it will simulate your calls over the internet, although your test environment do not have a connection to the public internet to make it work.

• Problems with phones Avaya IP & PIX 515

  I have a setup where an Avaya MedPro/CLAN is connected to the DMZ with Avaya IP phones even inside with H323/225/323RAS s active correction and an access rule of DMZ within the LAN IP address, phones don't register. What IP is enabled MedPro/clan started to work inside the phones.

  The PIX OS, I have is 6.3 (1), what is happening here? Any ideas would be much appreciated.

  Thank you.

  Disable any correction h.323, it does not work with the doorman avaya 'clan '.

  no correction h225 1720 h323 Protocol

  no correction protocol h323 ras 1718-1719

  Then make sure

  your static (inside the dmz) is configured correctly and the ACL have 1719/1720 tcp open

  In addition, open range of udp ports that correspond to your avaya "area network server configuration.