Major incompatibility in debugging for isakmp

It's the fifth router that has been set up to work with a firewall for VPN service remotely. All five routers have exact same cryptographic configurations apart from differences in IP. The firewall remote has the same settings for each router with the exception of the differences in intellectual property.

A router refuses to complete the phase 1 no discernible reason. He finds the peer with pre-shared key. He accepts the attributes and then fails to make a surveillance society. Newspapers of the remote firewall just tell the peer has expired. The only thing I see in debugging is important shift 25, major incompatibility of 237, etc.. What do the lines of debugging major incompatibility mean?

Here is a sample of debugging:

support useful treatment vendor id

Vendor ID seems the unit/DPD but major incompatibility of 38

support useful treatment vendor id

Vendor ID seems the unit/DPD but major incompatibility of 215

do you mind sharing the router config?

You also mention that he found the pre-shared key, can you please share the output of "show the isa cry her."

Tags: Cisco Security

Similar Questions

  • Debug Crypto ISAKMP

    Hello

    I've been trying to set up a virtual private network and when I ran this command earlier I received a lot of output and everything seemed ok.

    I could see also dest, src, etc... When I ran isakmp crypto his.

    All of a sudden I have nothing now, even when I debug above. His crypto isakmp command is now empty, too, see below.

    crypto ISAKMP his

    IPv4 Crypto ISAKMP Security Association

    status of DST CBC State conn-id slot

    Suggests that the problem is with the remote end? I'd always get the display using debug crypto isakmp if the remote end is down to debug?

    Just puzzled as to why the power has disappeared 'quiet '.

    Thank you

    Hello

    There could be several reasons for the same thing:

    --> Interesting traffic or other remote or local end has been interrupted for any reason any.

    --> That the ASA has been showing some debugs earlier, it is unlikely that the package can't the ASA now which in turn will hit the crypto ACL (interesting traffic) triggering therefore Cryptography tunnels and debugs him.

    --> There could be changes in configuration to the remote end ASA because of which the tunnel is not triggered.

    The best way to solve this problem is to follow the VPN traffic or the package for tunnel VPN from its source to its destination.

    I recommend the following:

    • Take screenshots on the SAA hence traffic is running and see if it's the ACL crypto. Check the ACL has hit counts for the same.

    http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a0080a9edd6.shtml

    • Select "debug crypto isakmp 127' & see if the tunnel is triggered and debugging is generated.
    • If not, then run the packet tracer and see if the VPN traffic passes all the checks, and that he is authorized by the VPN.
    • If traffic is allowed under the VPN to tracers of package Phase, and you still do not see the traffic being passed through the VPN, then it might a possibility that is happening in a different tunnel and pressing a crypto ACL overlap (as appropriate) on the same source ASA.
    • If the package is not seen hitting the firewall of the above capture, then the package can't certainly ASA and you will need to check the internal routing.
    • You can also see that the syslogs on the ASA local drops because of any function of firewall for VPN traffic destined for.

    To respond to your request, if the remote end has been down you wouldn't see debugs it unless the host is launch of traffic to the VPN to the local line. If the VPN traffic has been initiated by behind the ASA remote, and it is down then you would see not all debugs on the ASA local.

    I would like to know once you have reduced it more so that we can move forward and I'll be in a better position to provide my next course of action on this.

    Hope this has been informative.

    Kind regards

    Nick

    P.S. Please mark this post as solved if the information above has helped you identify the problem or at least you move forward to resolve the issue so that other users are benifited too

  • Device debugging for the camera application

    Hello

    I would like to perform device debugging for my camera application.

    Problem is that my application seems to work fine on the emulator, but I do not get the desired result on the device.

    But when I try to debug the application I can't access the camera. Whenever I try to access the camera or any other multimedia file I get a warning that I need to first unplug the unit.

    Any suggestions would be very helpful.

    Thank you

    Saket

    Hi, if you want to access a file media, first of all, go to options > memory > mass storage Mode support > power off.

    and now try to debug your application.

    PD: Sorry for my English.

  • By clicking on the icon of debugging for a procedure or function survey error ORA-00904

    Hi all

    By clicking on the icon of debugging for a procedure or function throws the error ORA-00904.

    Developer SQL 4.1.0.19.07

    Java 1.8.0_40

    OS: Linux Mint 17.1

    Developer SQL 4.1.0.18.37 on the same machine works very well.

    Clues?

    Thank you!

    degger error.png

    It is indeed regressed as RDBMS to 10g have object_id all_procedures notice. Buggy.

  • ORA-06525: incompatibility of length for CHAR or given GROSS

    ORA-06525: incompatibility of length for CHAR or given GROSS

    ORA-06512: at "SYS." UTL_FILE", line 127

    ORA-06512: at "SYS." UTL_FILE", line 1204

    ORA-06512: at line 14

    Note to moderators:

    956056 please don't report abuse on the positions that are not abusive.

    Just because you don't like an answer does not abuse.  People just make a point that you did not provide sufficient information so that they are able to help you.

    You have been informed to read the FAQ forum: Re: 2. How can I ask a question on the forums?

    Yet, you have not yet filed your code.  (and just the display of variable declarations is not code that does not).

    Remember, this is an evil abuse use the 'Report abuse' as long it to moderators.

  • (Possible cause: incompatibility of width for the word architecture)

    Dear Experts,

    I am facing the error when trying to apply the opatch below.

    Patch number 14703419

    Please go through and advise.

    System Command: /u01/applmgr/ORACLE/apps/tech_st/10.1.2/jdk/jre/bin/java -Doracle.installer.invPtrLoc=/etc/oraInst.loc -Dopatch.retry=10 -Dopatch.delay=30 -classpath "/u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/jlib/OraInstaller.jar:/u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/jlib/srvm.jar:/u01/applmgr/ORACLE/apps/tech_st/10.1.2/OPatch/jlib/opatch.jar:/u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/jlib/xmlparserv2.jar:/u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/jlib/share.jar" opatch/CheckConflict "/u01/applmgr/ORACLE/apps/tech_st/10.1.2/ Yes' ' / u01/applmgr/ORACLE/apps/tech_st/10.1.2 ' opatch.pl 1.0.0.0.62 14703419 '14703419' /u01/applmgr/ORACLE/apps/tech_st/10.1.2/OPatch/14703419/etc/config/actions /u01/applmgr/ORACLE/apps/tech_st/10.1.2/OPatch/14703419/etc/config/inventory

    Result:

    1. java.lang.UnsatisfiedLinkError: /u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/lib/linux/liboraInstaller.so: /u01/applmgr/ORACLE/apps/tech_st/10.1.2/oui/lib/linux/liboraInstaller.so: evil class ELF: ELFCLASS32 (Possible cause: incompatibility of width for the word architecture)

    in java.lang.ClassLoader$ NativeLibrary.load (Native Method)

    at java.lang.ClassLoader.loadLibrary1(ClassLoader.java:1957)

    at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1882)

    at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1843)

    at java.lang.Runtime.load0(Runtime.java:795)

    at java.lang.System.load(System.java:1061)

    at oracle.sysman.oii.oiip.osd.unix.OiipuUnixOps.loadNativeLib(OiipuUnixOps.java:372)

    to oracle.sysman.oii.oiip.osd.unix.OiipuUnixOps. < clinit > (OiipuUnixOps.java:119)

    at oracle.sysman.oii.oiio.oiiol.OiiolTextLogger.initializeInstallActionLog(OiiolTextLogger.java:1046)

    at oracle.sysman.oii.oiio.oiiol.OiiolTextLogger.initializeTextLog(OiiolTextLogger.java:923)

    at oracle.sysman.oii.oiio.oiiol.OiiolTextLogger.clearLog(OiiolTextLogger.java:821)

    Concerning

    Mohammed.

    Can you please eloberate and advise me on how to replace the java 64 bit by the 32-bit version of java

    Appreciate your quick response so far.

    Concerning

    Mohammed.

  • Debug crypto isakmp issue

    When you run the crypto isakmp debug is there a way to limit the output to only a specific piece of information.  Example, I want to see only the debug information for the x.x.x.x ip address and no one else.  Is it possible to do it with the debug command?

    Thank you

    Hello

    On the router, you can use the command "debug crypto condition equal."

    Debug condition crypto peers?

    group filter name of unity of the IKE peer group

    IKE peer host name filter FULL host name

    IPv4 filter address IP IKE peer

    subnet range of IKE peer IP address

    IKE peer username filter FULL domain name username

    In your case, the ipv4 option will limit debugs it to a host.

    There is a similar command that was made available in 8.0 (2) on the SAA.

    Debug condition crypto peers?

    HostName or the peer A.B.C.D address or host name

    Name of host or X:X:X:X:X peer IPv6 address or host name

    Let me know if it helps.

    Kind regards

    Loren

  • CSS does not not in the browser and have been debugging for hours, is there something I missed?

    Recently, I built a website for a client (boelmanshaw.com) in Wordpress. CSS of the site fits fine in all other browsers (IE, Chrome and Safari), but it does not work in Firefox. I've debugged the HTML code as I could, and I went through the CSS several times to see what could be the problem. I have not found anything that would be a problem. I'm not familiar with php, so I don't know if that would contribute to the problem, as well. I'm new with coding of websites, so any help would be greatly appreciated.

    I see in the error Console that you have made a typo: tour support (instead of a hug {and seems to be.)

    You can also use the Web Console (Web Developer > Web Console;) CTRL + SHIFT + K) to see this error.

    Warning: Expected ',' or '{' but found '('.  Ruleset ignored due to bad selector.
Source File: http://boelmanshaw.com/wp-content/themes/Ultra/style.css?9d7bd4
Line: 54

    a{color:#003267; text-decoration:none}
a:hover{text-decoration:underline; color: #535552}
p{margin:0 0 15px}
strong{font-weight:700}
em{font-style:italic}
li{list-style-type: none}
#leftlist{float:left; padding-right: 8px}
#rightlist(float:right}
small{}
pre{white-space:pre-wrap; white-space:-moz-pre-wrap; white-space:-pre-wrap; white-space:-o-pre-wrap; word-wrap:break-word}
hr{}
blockquote{border-left:2px solid #CCC; margin:20px; padding:0 0 0 20px}

  • Enable/disable debugging for all vi in project

    The question is quite simple. Is there a way globally enable and disable debugging. I know there is a slight performance penalty to have it activated, and I'm trying to figure out how much I can get out of my algorithm performance. Would be nice if I didn't have to go to each individual vi and toggle this setting.

    There is no simple way in the IDE to do this only for development purposes. If you create a version specification (executable source distribution, etc.) then you can adjust it for the distribution itself so that the 'construction' has debugging disabled. You can also script a simple to VI and programtically change this option in a group of the screws.

  • Error of debugging for LM3S1937

    Version of the software: LabVIEW for ARM 2009

    Image identification RealVIEW Debug connection

    Images of the debug error:

    Are there restrictions on the features of LM3S1937? Or any other reason?

    Thank you!

    It is the old version of the LM3S1937, debug JTAG interface BUG due.

  • SIGMATEL STAC 92XX C-Major HD Audio Driver for Windows 7?

    Computer: Dell XPS 420

    OS: Windows 7 64-bit

    Sound card: SIGMATEL STAC 92XX C - Major HD Audio

    I upgraded my machine to Windows 7 64-bit a few weeks; However, the sound card is malfunctioning. I have the Logitech Z-5500 Digital 5.1 Speaker and is necessary to install the MB of Sound Blaster Audigy software. When I installed the Sound Blaster Audigy MB software, I got an error message "sound card is not found.

    Without install Sound Blaster Audigy software Mo, I still could hear the sound of two speakers (not all 5). I'm just wondering if Dell has laterest driver for SIGMATEL STAC 92XX C-Major HD Audio?

    Go to the Microsoft catalog and search for Sigmatel STAC / IDT?

    HDAUDIO\FUNC_01 & VEN_8384 & DEV_7627 & SUBSYS_80863001 & REV_1002
    HDAUDIO\FUNC_01 & VEN_8384 & DEV_7627 & SUBSYS_80863001

    Catalog.Update.Microsoft.com

    R171786.exe

    R190517. EXE

    R180044. EXE

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801B5%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801D8%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801C2%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801C8%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CC %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801D4%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801D6%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CE %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CF %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801C9%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CA %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CB %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801D3%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801BD %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801EE %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801EF %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801F6%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801CD %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_10280201%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_10280218%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_102801F5%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7690&SUBSYS_1028022A %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280204%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280217%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801F9%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801FA %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801FE %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801FF %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280206%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280200%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280232%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_1028024A %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280212%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280213%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280216%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280219%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_1028021B %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280241%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_1028024B %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801F2%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801FD %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_1028021F %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280229%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801F8%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_1028021C %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801F1%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_102801FC %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_76A0&SUBSYS_10280228%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7680&SUBSYS_102801BF %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7680&SUBSYS_102801D7%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280209%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_1028022E %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_1028022F %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280230%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_102801F3%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280227%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280242%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280243%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_102801F7%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_1028023A %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_1028023B %

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280244%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_10280245%

    ST. DeviceDesc%=STHDA,HDAUDIO\FUNC_01&VEN_8384&DEV_7616&SUBSYS_1028020A %

  • Unable to generate the debugging for bb10 token - get java error

    I used the blackberry-debugtokenrequest (from blakberry 10 filepath sdk) command to create a token of debugging, and I get a java error message:

    'java' is not recognized as an internal or external, order

    operable program or batch file.

    I have previously set up for the blackberry Tablet key signing and use this password for the keystore.  I use the windows operating system 7.  the debugtokenrequest I used was: C:\Program Files (x 86) \Research In Motion\BlackBerry 10 WebWorks SDK 1.0.4.7\dependencies\tools\bin.   Anyone know what is causing my problem?

    blackberry-debugtokenrequest -storepass 
    -devicepin

    It seems that java is not on your path:

    'java' is not recognized as an internal or external, order

    operable program or batch file.

  • Unable to create a debugging for my playbook device token

    Hi all

    I have a problem to create a debugging token to install on my playbook.

    * I installed the SDK for a long time (before the playbook was here), when I installed first of all, there was no debugging token / COMINCO files

    * Then I received my COMINCO file by mail, but has not used as I was more accustomed to using the Simulator.

    * I have since released an Android application.

    I have some barsigners files in the folder "C:\Users\MY_NAME\AppData\Local\Research In Motion". I think that they were created when I published the Android app.

    So now when I try to create a token of debugging with this command:

    BlackBerry-debugtokenrequest - storepass XXX - XXX c:\temp\debugtoken.bar devicepin

    And I have this error:

    Error: The signature on the request of code signing did not check. The probable cause of this problem is entered a wrong password CSK.

    My store is correct (I have another error if I intentionally use a wrong password).

    Can this be my PBDT.csk file that is not registered?

    How can I change this?

    Thanks for any help,

    I need it because I now have a bug that does not intervene in the ripple or on the simulator of the tablet.

    Emmanuel / Alocaly

    OK, the different password for the developer certificate (p12) and RIM Code signing key would cause problems here.  Rename your author.p12 to something else and create a new p12 with the same password as your Code RIM signing keys.  Do not delete the barsigner files or you will not be able to sign the upgrades of your applications.  This command will allow you to create a new file p12.

    blackberry-keytool -genkeypair  -storepass  -dname "cn="

  • Cannot install the debugging for bb10 token: error in tag hr

    After having successfully generated a debugging token, jcdebug.bar, I tried to install it using blackberry - deploy and got a fatal system error.  My entry of order/.output line is below.  What am I doing wrong now?

    Token of debugging C:\Users\Jacquelyn\Documents\Jacquie\Blackberry\bb10 > "C:\Program Fil".

    are (x 86) \Research in Motion\BlackBerry 10 SDK WebWorks 1.0.4.7\dependencies\tool

    s\bin\blackberry - deploy"installDebugToken - jcdebug.bar - 192.168.1.10/24 device

    -password mypassword

    [Fatal error]: 5:3: the element type "hr" must end with the corresponding end

    -tag «»

    Error: Authentication failed due to system error

    DOH!  I forgot to put my (dev alpha B) device in development mode.  Also used the IP address specified for the development.

    Fixed a problem.

    Now we'll see if I can put the debug token...

  • Eclipse debugging for torch/OS6 Simulator

    I downloaded the Simulator OS6 and I can't seem to get the debugger to work. It appears as an option in Eclipse, but when I run the debug it does not load my application with the Simulator... Anyone know what I'm doing wrong?

    I'd really rather not explain how I did this job, but I will...

    I assumed that the download of the Simulator on the BB site package included the JRE6.0.0; of course, I was wrong! Once I followed the instructions (ahem... RTFM) I was able to update Eclipse, get the JRE 6.0.0 and everything works again...

    The eclipse instructions: http://us.blackberry.com/developers/javaappdev/javaupdate.jsp

    Thanks for your help... now let's act like it never happened...

Maybe you are looking for

  • How to install Windows Vista Bussiness on Tecra A4 SP211?

    I can't install vista. The accidents of the screen and freezes and the installation does not complete.None of the experienced people who has successfully installed is welcome! TKS.Rafa48

  • Good ability of Photos except that it is

    Hi all My question could be linked to the camera instead of the Album application, however since the Album is an image treatment it was my best bet on the forum... I would like to know if "Sound picture" can be shared through social media... For exam

  • Windows cannot find C:\WINDOWS\system32\rundll32.exe error message

    original title: I still need help... help please! Windows cannot find C:\WINDOWS\system32\rundll32.exe Hello, I have windows vista and when I try to open certain programs, like Adobe or change the time in the control panel............... etc... the c

  • (Redirected) Dell coming 11 Pro micro SD card tray

    The micro SD card tray (as described on page 11 of the Dell coming 11 Pro user guide) broke, and I'm trying to get a replacement. After 16 calls to Dell... anyone know what I'm talking about (even if I use the EXACT user guide PHRASE to describe the

  • How to get the emial address

    are there methods to retrieve the device email address?