Moving from SSL VPN licenses to other ASA

Similar Questions

• ASA 5505 SSL VPN license update

  Hi all.

  Our ASA 5505 with DATABASE default license allowing only 10 simultaneous vpn sessions (including 2 Anyconnect + IPsec). attached a TXT file with the license information. This Firewall is's use only for vpn access, and we less vpn tunnel vpn IPSec-L2L, anyconnect client SSL and IPSec client access configurations vpn to the top and race walk,.

  We are in terms of upgrading vpn license to archive IPSec 10 and 10 Anyconnect and 1 anyconect mobile VPN sessions in time. so my questions are;

  1. can I buy "ASA5500-SSL-10 =" accounting and to upgrade our ASA 5505 without having to buy "L-ASA5505-SEC-PL =" license of pus of security.

  2. asa use to upgrade only Anyconnect SSL vpn license while keeping 10 vpn IPSec comes with the base license.

  Thank you & you expects value comment

  Thank you

  JCK

  1. Yes.

  2.Yes.

  If you want to keep Clientless SSL VPN you do not want to continue with the addition of the ASA5500-SSL-10 = part. If you can do without client (including the conversion the two existing ones), more economically, you can opt for Security Plus and AnyConnect Essentials licenses. (US$ 800 vs price $1250).

  In both cases, the Mobile requires the AnyConnect Mobile (ASA-AC-M-5505) license.

• Disable SSL VPN license

  Hello

  I have 2 5510 ASA and I'm in a pinch with needing a failover ASA to implement. I have an ASA test I put in as a firewall waiting in an active scenario / in sleep, and this ASA a user 10 SSL VPN license applied. My ASA primary I'll put this in place with only 2 standard user and fails it of Wizard config HA when I run through it. The message I get is "Test of compatibility of the license for many clientless SSL VPN peers has failed." How can I deactivate the license 10 user on my unit of analysis so I can bring it failover?

  The two ASA have a license of SecPlus.

  Thanks for any help,

  Brett

  Keep your current activation key you can reapply after your tests, and request a new activation key of [email protected] / * / unlicensed SSL VPN to test your failover.

• How SSL VPN packages for two ASAs clustered licenses

  Hi all!

  If I have installed two Cisco ASA 5550 (ASA5550-BUN-K9) in failover mode, which I know support only 2 concurrent sessions of SSL VPN and you want to upgrade my boxes to support 15 AnyConnect SSL VPN sessions, how many licenses packages I need to buy?

  An ASA5500-SSL-25 for both boxes or two ASA5500-SSL-25 for one per box?

  Depends on what version of ASA you are running.

  If you are running version 8.3 and above, then you just buy 1 ASA5500-SSL-25 for a failover pair and it would work. If you buy 2 ASA5500-SSL-25, one license per box in failover pair, then the license gets grouped into 50 SSL user license.

  Here is the license information for ASA version 8.3 for failover pair:

  http://www.Cisco.com/en/us/docs/security/ASA/asa83/license_standalone/license_management/license.html#wp1315746

  For ASA running version 8.2 and below, you are required to buy 2 ASA5500-SSL-25 (one of each ASA in the failover pair) as the license should be exactly the same for the pair to failover to work, in the earlier version of the SAA.

  Hope that makes sense.

• SSL VPN license for ASA

  It must be an easy question - but I'm having a hard time finding an answer. How are the SSL VPN to the end user a license?

  Let's say I have 300 users, SSL, but only 20 concurrent SSL at any time. Do I need licenses for the 300 full or 20 competitors?

  Thank you

  Jim

  Hey Jim,.

  SSL licenses for only simultaneous connections. The only limitation you will encounter is how SSL sessions each platform supports (i.e. 750 concurrent sessions on an ASA5520).

• SSL VPN IP address other than the IP address of the interface?

  Hi,
  
  Is it possibe to use a differnt IP Address from the same Subnet of OUTSIDE
  
  INTERFACE? Instead of Interface IP Address itself. The Idea behind is,
  
  Clients should not use OUTSIDE Interface IP Address for SSL VPN, but whereas they can
  
  use from the IP Address Pool of OUTSIDE Interface.
  Regards

  Brassart Abbas

  If SSL is completed on an ASA firewall, you can finish it on all other ip addresses but the external interface.

  If it is completed on a router IOS, Yes, you can use a different ip address to put an end to the SSL VPN connection.

  Hope that answers your question.

• Calculation of SSL VPN license

  Hello

  I need to purchase licenses for my SSL VPN (AnyConnect) 2901 router, and I would like to know how it is affected.

  If I buy a license 10 users, it is up to the 10 named user, or it is counted by concurrent users?

  If a user connects from a laptop computer and a mobile phone at the same time, with the same username, it counted as 2 user license, or just one?

  Also, AFAIK, the AnyConnect Essentials license is only available to ASA and not IOS routers. Is that still OK?

  Thank you.

  The number of licenses using simultaneous connections, regardless of the associated user ID.

  75 connected both unique usernames or a different user connected of 75 endpoints name would be count as 75 licenses in use. Laptop more phone = 2 users if the connections are simultaneous.

  The Essentials vs Premium distinction is unique to the ASA. Premium features only as a clientless SSLVPN, hostscan etc are not available based on the IOS SSL VPN

• ASA5510 must add 25 peer SSL VPN Licenses, NM found link in this message

  I just got my new ASA5510 and also an authorization key product for "ASA 5500 VPN 25 SSL peers License ', but I can't for the life of figure me out how to install these licenses. I tried to enter the key provided, but when I do the ASA returns an error "type 4 or 5 Tuple Activation-Key."

  Is there a place on the Cisco site, where I 'activate' this key for a licence to be installable on the SAA?

  https://Tools.Cisco.com/swift/licensing/PrivateRegistrationServlet

  Thank you

  Rick

  Once you put your code PAK page you mentioned, it will ask you to verify the end-user and your contact information. At the end of the process (step 4), you will receive an email with the activation key. Then just enter it on the SAA by using the command of activation key (detailed instructions will be present in the mail as well on how to do this).

  Please rate if useful.

  Concerning

  Farrukh

• SSL VPN license key

  Hello

  ASA with license essential SSL VPN offers full access to the business applications with CIsco Anyconnect client of tunneling. What kind of Protocol use this connection (full access)? ¿SSL or IPSEC?

  Thank you

  SSL

• SSL VPN license

  Hello

  We have a customer with the ASA license.

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect for Linksys phone: disabled
  AnyConnect Essentials: enabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  But when I look at the Tracking tab of the VPN, they have 40 to 50 VPN SSL with client sessions active at any given time. Is this correct or does pass the license?

  Hello

  The license shows up, you can have 2 SSL VPN peers.

  the following link gives you all the details of the available licenses. Please choose according to your requirement.

  http://www.Cisco.com/en/us/partner/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80402e39_ns347_Networking_Solutions_Brochure.html

  Kind regards

  Anisha

  P.S.: Please mark this message as answered if you feel that your request is answered.

• Cisco 1900 series ssl vpn license

  Hello

  Since the FL-SSLVPN10-K9 license cannot be purchased, I wonder what are the options on my router CISCO1921-SEC/K9 should I now if I want to use SSL VPN, if any?

  Thanks in advance

  Kind regards

  Herman

  I think the best way is to allow the new AnyConnect 4 which is also valid for the IOS-based VPN gateways:

  http://www.Cisco.com/c/dam/en/us/products/security/AnyConnect-og.PDF

• Third-party SSL VPN ended the DMZ ASA

  Hi all

  Any help is appreciated. Is it possible:

  I have a DMZ set in ASA 5520, and worked well so far. The DMZ subnet is 192.168.10.0/24 and IP on the DMZ interface is 192.168.10.1. Now, I'm trying to add a third-party SSL VPN device (not Cisco). The device has an IP 192.168.10.101. The SSL VPN appliance will give IP addreess SSLVPN customers in the range of 192.168.20.x. After the connection is established, the client is indeed getting the IP addr 192.168.20.x. However, clients are unable to connect to the internal LAN. If I change the IP address range clients on the same subnet that the area demilitarized, everything works. My question is that, as customers SSLVPN are complete on the demilitarized zone and get a different subnet IP address, how can I / road map these addresses before they6 can access internal network inside the interface, or it can be done at all?

  All advice is appreciated.

  You just need to add the routes appropriate on the SAA for this pool. And also on any Layer 3 routing devices inside the ASA.

  Concerning

  Farrukh

• prevent the SSL VPN user to access ASA cli

  Hello

  I set up multiple users on my ASA in its local database.

  These users are used for the ssl vpn connection, but the problem I have is that users

  also have SSH access. Is it possible to avoid this?

  Thank you

  Hello Raf,

  If you do something like this:

  username xxx attributes

  type of remote access service

  the user should not get access CLI more.

  Kind regards

  Bastien

• Cisco 1941 ssl vpn license

  Anyone know if the FL-WEBVPN-10-K9 will work on my 1941 or is it only for the older gen SRI?

  My router has already installed security license, but I think I need a VPN SSL to SSL license.

  Thank you

  1941 supports up to 75 users of ssl vpn.
  You buy FL-SSLVPN-10 | 25. license 100 - K9. FL-WEBVPN-X are only supported on ISR routers 1st generation 1800,2800...).

• Help! JavaScript works not when the object is moved from one page to the other!

  Hi all:

  I am new to Adobe Livecycle Designer (version 8.0). I created an interactive pdf form of 3 pages with many objects (text fields, radio buttons, drop-down lists, etc.), our company wants to quickly start to use.

  I'm having trouble with some of my Javascript does not not with some of my items on page 2 of the form. Specifically, there is a drop down menu to "Country" on page 2 of my form. When the user selects, for example, 'United States' in the list, I have the Javascript code that is supposed to change the 'currency' list drop-down to "Dollars" rawValue accordingly (on the change event).

  I think that my Javascript syntax is correct, but I am not sure. Here's my simple Javascript associated with the "Country" drop-down list (Note: rawValue 80 = 'United States' and 105 rawValue = "US $"):

  -

  ---

  Form1. Page1.cmbContactInfoCountry::change :-(JavaScript, client).

  ---

  If (this.rawValue == 80) {}

  cmbCurrency.rawValue = 105;

  }

  It sounds pretty simple and it WORKS when my "Country" drop-down list is moved to page 1 of the form, but it WON'T WORK when I move the combo box "Country" return to page 2 of the form (i.e. where it belongs).

  Anyone has suggestions or solutions? I spent probably 6-8 hours of racking my brain trying to figure out why it works when on a single page, but it does not work when to move to another page. I guess I can have corrupted something OR that I not address fully the proper name of the object?

  Help, please!

  Frustrated and helpless, near Chicago.

  Taylor T

  Yes, it's a quirk of... in the drop-down lists when you select an item in the DOF it is not committed until you exit the field, unless you do the following:

  If (this.boundItem (xfa.event.newText) == 1) {}

  cmbCurrency.rawValue = 1;

  }

  ElseIf (this.boundItem (xfa.event.newText) == 2) {}

  cmbCurrency.rawValue = 2;

  }

  The xfa.resolveNode stuff was not necessary that both objects are of the same subform, and as such can 'see' each other.

  Think like a folder structure subforms - elements can see what is in their own folder but will say where to find things in other folders. If cmbCountry was subform1 and cmbCurrency was so in subform2 that rawValue above lines would look like:

  subform2.cmbCurrency.RawValue = 1;

  It's a good idea to name all your objects, subforms, etc. it is to work with script is much easier - so you won't have to deal with things like these pieces of xfa.resolveNode you had before (as well). He ones because you have more than one subform called "subform", the number of hooks is the Instance number (when you have several of the same object) if the program has to differentiate between the various "subform".

  The number of instance come in handy, but for things like the rows of the table and so on when you need to make calculations.