NX - OS enable ping and traceroute

Hi all!

At my new job, I have a cisco nexus switch 5548 and I never worked with her before.

Can someone explain to me how to activate the command 'ping' or 'traceroute' on this subject?

P.S I hear it can be activated with the command "function (config) #"... Is it true?

THX in advice

Hello

You must enable any feature to use ping and traceroute commands.

Here's the documentation on this subject:

Ping:

http://www.Cisco.com/c/en/us/TD/docs/switches/Datacenter/nexus5000/SW/co...

Traceroute:

http://www.Cisco.com/c/en/us/TD/docs/switches/Datacenter/nexus5000/SW/co...

Tags: Cisco DataCenter

Similar Questions

  • Cisco ASA - need to allow Ping and Traceroute

    Hello

    I am able to ping my remote counterparts, but can not trace.what I'm missing here?

    object-group service PING_TRACE
    ICMP service object
    service-object icmp traceroute
    the ICMP_ACCESS object-group network
    object-network 203.121.10.0 255.255.255.0
    host of the object-Network 222.77.187.292
    host of the object-Network 231.27.20.18
    host of the object-Network 198.18.171.220
    host of the object-Network 129.26.179.202
    host of the object-Network 218.192.63.146
    host of the object-Network 94.62.250.62

    #sh access-list Test_access_in
    access-list Test_access_in line 6 Note Allow set of hosts to PING and ANY TRACE on the outside - for monitoring.
    allowed to Access - list Test_access_in line 7 scope object-group PING_TRACE-group of objects any4 (hitcnt = 0) ICMP_ACCESS 0x48a9083e
    allowed to Access - list Test_access_in line 7 extended icmp 203.121.10.0 255.255.255.0 any4 (hitcnt = 0) 0xce1e8a24
    allowed to Access - list Test_access_in line 7 extended icmp host 222.77.187.292 any4 (hitcnt = 0) 0xf57d731f
    allowed to Access - list Test_access_in line 7 extended icmp host 231.27.20.18 any4 (hitcnt = 0) 0xb25e6675
    allowed to Access - list Test_access_in line 7 extended icmp host 198.18.171.220 any4 (hitcnt = 0) 0xd1f4dfa4
    allowed to Access - list Test_access_in line 7 extended icmp host 129.26.179.202 any4 (hitcnt = 87) 0 x 45874268
    allowed to Access - list Test_access_in line 7 extended icmp host 218.192.63.146 any4 (hitcnt = 0) 0x737f20fb
    allowed to Access - list Test_access_in line 7 extended icmp host 94.62.250.62 any4 (hitcnt = 0) 0x4223d717

    #sh run access-group
    Access-group Test_access_in in interface Test1

    #ping 231.27.20.18
    Type to abort escape sequence.
    Send 5, 100-byte ICMP echoes to 211.27.20.10, ti

    #traceroute 231.27.20.18

    Type to abort escape sequence.
    The route to 231.27.20.18

    1   *  *  *
    2   *  *  *
    3   *  *  *
    4   *  *  *
    5   *  *  *
    6   *  *

    meout is 2 seconds:
    !!!!!

    #traceroute 231.27.20.18 source Test1

    Type to abort escape sequence.
    The route to 231.27.20.18

    1   *  *  *
    2   *  *  *

    Hello

    You must enable error control icmp see all intermediate hosts.

    Policy-map global_policy

    class inspection_default

    inspect icmp errors

    Take a look at this link for the order reference:

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/ASA-command-reference/...

    The reason for this behavior is that by default ASA (a safety device!) allows you to hide all

    hosts on the path for messages time exceeded ICMP behind a NAT

    I would like to know how it works,

    Please don't forget to rate and score as correct the helpful post!

    David Castro,

    Kind regards

  • My email on my iPad (version 8.4.1) application froze on a white page. I tried to power down and restart. I know I get emails that I can hear the ping and see numbers on the app. It has been frozen for a day and I have no way to display

    My email on my iPad 2 (IOS 8.4.1) froze last night on a blank page I was trying to send a few photos. I know I get emails that I can hear the ping and my email application shows that I have two new. I tried to put this off, then restart, but nothing changes. When I type my email application it goes to the blank page and after a few seconds goes back to my home page. I'm leaving on a trip to Europe at the moment I'm in a bit of panic. Any help will be greatly appreciated.

    You tried to close the Mail application via the taskbar of the iPad: force an app to close on your iPhone, iPad or iPod touch - Apple Support ?

  • Trying to get on my email, the following statement comes from the IPU: "we're sorry, but you must enable cookies and Javascript to use your username with this site. I click on "here", but nothing happens. How to enable the amd Javascript cookies?

    Try to get t my email, this happens: we're sorry, but you must enable cookies and Javascript to use your username with this site.
    How can I do this?

    George Szántó

    [email protected]

    see similar question answered https://support.mozilla.com/questions/836913

    To be notified of updates to a question, if this is your problem or not just click on the "Get email notifications" and follow made the choice. Only the original poster can mark it as resolved, so there should be a slight difference in choice as an original poster and where you lock on another issue. Notifications only apply to individuals the question where is entered.

  • Cannot attach email word documents get the message 'enable documents and data '.

    Cannot attach a word document to an email. I get the message 'Enable documents and data' and it says that it is disabled. Don't enter iCloud setting there is no Document and data parameter. Is it because I use a free version of work?

    Whether the app is the word document?

    You can view the document word on the iPad?

  • Device photosmart c6380 maintains processing a job. Cannot delete it. Enabled, unplug and authorized in Quebec

    Original title: photosmart c6380

    Device photosmart c6380 maintains processing a job. Cannot delete it.  Enabled, unplug and allowed to help Québec

    Hello

    1. have you made changes on the computer before this problem?

    2. which version of the Windows operating system is installed on your computer?

    I suggest you uninstall and reinstall the driver printer HP Photosmart c6380 and so software and check if it helps.

    Uninstall a program: http://windows.microsoft.com/en-US/windows7/Uninstall-or-change-a-program

    Install a program: http://windows.microsoft.com/en-US/windows7/Install-a-program

    Driver & Software Downloads - HP Photosmart C6380 all-in-One Printer: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=3560280

    It will be useful.

  • How can I disable all the pings and tones and notes and sounds of the HP Officejetpro 8610?

    I can't tolerate the noise.  How can I disable all the pings and tones and notes and sounds of the HP Officejetpro 8610?  This 'thing' emits a beep and the pings and plays music.

    Thank you

    Sam

    Hi Sam,

    On the front panel of the printer, scrool main screen to the right and the clock setting icon.

    Then click Printer Setup, and then select sound effects Volume.

    Select and confirm, that should disable all these sounds.

    Shlomi

  • Office of ping and distance between the player and the second computer

    I have a laptop running VMWare Player 12 (NAT) and a PC connected to a router.  All 3 running under Windows 7.  All firewalls is turned off.

    Win 7 guest may ping the laptop computer, the router and the PC.

    Portable Win 7 can Pinger the PC, router and Win 7 guest.

    The PC can ping the router, the laptop, but not the comments of Win 7.  Why not?  (Ping results in a timeout or a "Destination host unreachable")

    I can run Remote Desktop from the laptop at the prompt of Win 7, but I can not run Remote Desktop on the computer in the prompt of Win 7, which is what I'm really after.  Why not?

    Remote Desktop between the PC and the Win 7 guest would not work any direction.

    For other reasons, I must leave the network connection of the player in NAT mode.  Ping and remote desktop work fine in bridged mode.

    I ended up adding a second card (bridged) network under Remote Desktop and devices that I can use to ping and the application that is using NAT also works very well, so that solved my problem.

  • Enable advanced tagging vs enable accessibility and reflow with tagged Adobe PDF

    Is anyone know the difference between these two parameters in the PDFMaker preferences?

    Enable advanced tagging vs enable accessibility and reflow with tagged Adobe PDF

    I can't find any information that distinguishes these two parameters are mutually exclusive. I am trying to decide what is the best when you create a PDF document that is signposted from MS Word. If someone has an idea, I would be very happy.

    "Advanced marking" is changing the way that some elements of the page are defined (table of cells, lines, boxes, etc.), who makes the most reliable conversion of "Visual" in PDF Acrobat forms fields. You must have the option "enable accessibility and reflow with tagged Adobe PDF" as well on, or tags are not created at all.

  • Cannot get SW1 to the second network of ping and can't get the HQ router to ping SW1.

    Hello the forum community.  I am new to Cisco Configuration and cannot understand why, in the attached packet tracer file, I can't have my SW! switch to ping to the gi0/1 interface of the branch office router and beyond.  I also can't understand why I can ping to the gi0/0 interface on the router in the branch office router HQ, but cannot ping the switch SW1 and beyond.

    Ideally, I'm trying to configure the network so that PC1 can ping 172.16.1.100, which is a loopback on router HQ.  I ping the closure of the branch office router, but not the switch SW1.  I cannot ping the gi0/1 interface on the router of the branch of the SW1 switch and do not understand why.  I can also ping the gi0/0 interface on the router in the branch office router HQ, but cannot ping the switch SW1 of the HQ router.

    PC1 - 10.1.1.100 255.255.255.0

    SW1 - VLAN 1 - 10.1.1.11

    Branch gi0/0 - 10.1.1.1 255.255.255.0, gi0/1 - dhcp assigned as 209.165.201.1 255.255.255.224, dynamic NAT activated with access-list 1 (permit 10.1.1.0 0.0.0.255), the pool name is NAT_POOL with the address range of 209.165.201.5 - 10 255.255.255.224 as NAT address range.  I can see it working with debug ip nat active when I ping the router address 10.1.1.1 HQ, although I have test the ping without NAT and it is always successful.  Gi0/0 inside the nat, g0/1 outside the NAT.

    HQ gi0/0 - 209.165.201.2 255.255.255.224, dhcp server enabled to provide an address for the router in branch gi0/1.  I had to add a static ip route 10.1.1.0 0.0.0.255 209.165.201.1 in order to be able to get the ping to the router HQ to branch router gi0/0 to work.  Don't know if there is a better way to do it, but it's the only way I could make it work so far.

    You will need to rename the .txt file, attached to. pkt.

    Thanks for any help!

    Hello

    The switch has ip routing enabled, if so disable it and give it a default gateway instead

    no ip Routing
    IP default-gateway x.x.x.x

    RES

    Paul

  • two virtual machines on esxi, vm linux server can ping and ping to the outside, windows can ping but incoming requests timeout

    Hello

    I have an ESXI server with two network cards, each connected to separate the subnet in the same Cisco switch.

    First interface is in 10.231.5.0/255.255.255.0 and the second is 192.168.118.0/255.255.255.0

    Initially, I built a virtual machine with MS Windows 2003 R2 Standard with two network interfaces with static IP addresses on both subnets. 10.231.5.153(Gateway configuré sur cette carte réseau) and 192.168.118.153.  It has also installed vm tools.

    Second built vm is Ubuntu 8.10 with two network interfaces and two static IP a linux server in each subnet. This virtual machine has never had no problem contacted subnets one bit and he can go out on all of the subnets that are routable through the switch. Static IP addresses are 10.231.5.152(gateway est configuré sur cette carte réseau) and 192.168.118.152

    The Windows virtual machine has always been a bit flaky. Sometimes he would not be able to ping on all interfaces (while the State of the network in Windows showed the incoming and outgoing packets).  Sometimes he could ping another Vm and ESXI management IP but could not ping to the outside on the network 10.231.5.0 or 192.168.118.0. Deactivation and activation of network interfaces seem to make a difference with outgoing network access is enabled. However, if I try to ping back part of the same subnet a machine outside the ESXI Server ping timeout. It's weird as after having activated a deactivation of the network interface, that he even manages to ping subnets a bit far, but pingees machines cannot he ping back. However, these machines have no problem ping to the management of ESXI or Linux VM interface. Restart the machine virtual Windows translates the EPS of no longer being able to ping up to deactivation and activation of cards network again.

    I tried to activate the Promiscuous (the Accept value) mode on computer management virtual and vSwitch (vmnic1 and vmnic0 appear in the collection of NETWORK adapters window), but it did make a difference.

    Pointers would be very much appreciated.

    Thank you

    Windows Firewall is enabled?

    ---

    VMware vExpert 2009

    http://blog.vadmin.ru

  • Firewall settings is enabled, disabled and cannot open the Web page in Internet Explorer: "IE can not display the webpage".

    Original title: how to manually configure the firewall?

    Let me know how I can configure my firewall setting manually as it is said that your firewall setting is disabled. I have HomeXP, SP3. I am now faced with another problem with IE8 when I try to open another page, I find this error-"IE can not display the webpage". Sometimes, it works when it is updated and not some time.

    Hello

    1. do you use third-party security software that runs on the computer firewall settings?
    2. What is the error code / message displayed when trying to turn on the Windows Firewall?
    Please follow these steps in the KB article to turn on the Windows Firewall.
    Step 1
    How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?
    Step 2
    How to enable Internet Connection Firewall in Windows XP
    Follow the steps in order and read the content.
    See also,

    "Internet Explorer cannot display the webpage" error in Internet Explorer

    http://support.Microsoft.com/kb/956196

    WARNING: Reset Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings


    I hope this helps.
  • Unable to see the computers in the workgroup or server to print to my HP laptop, but I can all ping and access the internet through the router.

    I have a laptop HP with XP pro. I have a network with 2 computers laptops (Dell and HP), 1 office and 1 DP300U DLINK print server with a static IP address. I use a LINKSYS WRT110 router. Everything is connected through this router. I can ping ALL laptops, the office and the print server. I can access internet from all laptops and office. All THE MACHINES are in the same workgroup. Only from my DESKTOP (XP HOME), I can click on FAVORITES NETWORK, click VIEW group of WORK COMPUTERS and I can see the other compters and the print server. However, since my computer Dell laptop or HP LAPTOP (XP PRO) I can PING the router and the journal in it, all the other machines and print server but can NOT SEE THE OTHER COMPUTERS or ACCESS THE PORTABLE HP computer or the other laptop. I turned off all firewalls and firewall McAfee (PORTABLE HP computer) and still no joy. I think that there is a box ticked somewhere or the one that is checked and who should not, but I can't find out where it is or something else to look at. Any ideas would be appreciated.

    I suggest you take a look at:

    http://support.Microsoft.com/kb/318030/

    You can run fixit in the PC that encourage the problem this fixit automatically.

  • Problems with ping and 56 k modem about half current speed.

    I have a few questions.

    I've switched & my internal modem says it's 56 k. I know that I won't get a full 56 k, but I'm only running at about 26 k. Why what can I do about it?

    Additionally, every time that I ping ALL websight, it always comes back with: request timed out, 0 packets received, 4 lost packets, 4 packets sent, 100% loss. I can't understand it and I hope someone can explain to me why and how to fix it. I'm NOT "computer illiterate"!

    Help, please!  Thank you

    Here's what I'm running:

    System: Intel (r) Pentium (r) D CPU 3.00 GHz 2.99 GHz (dual processor);   1.00 GB of RAM, 32-bit operating system.   223 GB int hard drive. & 298 GB ext HDD.

    Operating system: Windows Vista Ultimate sp2

    Browsers: ie9 and mozilla firefox 4

    Modem: PCI Soft Data Fax Modem with SmartCP

    Hi desandjol,

    1. are you able to ping the loopback adapter (that is to say-ping 127.0.0.1)?

    You must contact the ISP to find out why you can't ping websites.

    You can also check with the manufacturer of the modem if no firmware update is available. It is available even download and check.

    Hope this information is useful.

  • What is an enabling technology and why is it prevents a restore of the default gateway

    I started with a virus. I have a gateway m series laptop PC with vista home premium.  My unit would be shut down and restart when I tried to put my password to open it.  I could only use safe mode - last configuration to open it.  I used the malwarebytes, which was recommended, I also used the spybot.  It does not start unless I'm in safe mode.  I'm guessing that a restart of the plant will help but I get this kind of thing enabling technology.  someone please help.  I have my little bank account as an online and can even use it to buy anything.

    For questions on the process of the gateway to restore factory settings, you need to talk to the Gateway http://support.gateway.com/support/ask_gateway.aspx technical support - the recovery process is theirs and not Microsoft.  Here's more help from the http://support.gateway.com/s/SOFTWARE/Medialess/FAQ/SUPPAGE01su44.shtml gateway that can answer these questions without having to talk to anyone.

    I don't know what the enabling technology is, but if it has to do with the recovery process, you must contact the gateway to solve the problem that we don't have access to that information.

    I'm sorry, we can not help you more, but it is a problem of gateway.  Keep in mind that a restore to factory settings will wipe your car clean of all backup so your important data before do you.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

Maybe you are looking for