«Problems with remote access with ASA 5505-, this is the error "the remote peer is no more answers»
Hello
By train I got a remote access IPSec VPN, when I have all the performed configuration and try to access remote show software vpn client (cisco) the following message:
"The remote peer is no more answers.
I know where is the problem.
Network information:
ASA TO LAN - 1:
192.168.1.0 - 255.255.255.0
the interface vlan 1:
IP: 192.168.1.1 - 255.255.255.0
the interface vlan 2:
IP: 100.100.100.1 - 255.255.255.252
REMOTE LAN ACCESS:
192.168.10.0 - 255.255.255.0
ASA-1 configuration:
* IP address pool
local IP VPNPOOL 192.168.20.1 pool - 192.168.20.254
* Split tunneling
splittunnel list standard access allowed 192.168.1.0 255.255.255.0
* NAT configuration
object obj LAN
subnet 192.168.1.0 255.255.255.0
object obj-vpnpool network
subnet 192.168.20.0 255.255.255.0
NAT (inside, outside) 1 static source obj-local obj-local destination static obj-vpnpool obj-vpnpool no-proxy-arp
* Group Policy
internal group company-vpn-policy policy
attributes of vpn-company-policy-group policy
VPN-idle-timeout 30
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list splittunnel
Configure the IPSec
IKEv1 crypto policy 10
3des encryption
sha hash
preshared authentication
Group 2
life 3600
Crypto ikev1 allow outside
crypto isakmp identity address
Crypto ipsec transform-set esp-3des esp-sha-hmac RA - TS ikev1
Dynamic crypto map DYN_MAP 10 set transform-set RA - TS ikev1
card crypto VPN_MAP 30-isakmp dynamic ipsec DYN_MAP
VPN_MAP interface card crypto outside
Create tunnels
tunnel-group vpnclient type remote access
tunnel-group vpnclient-global attributes
address VPNPOOL pool
by default-group-company-vpn-policy
tunnel-group vpnclient ipsec-attributes
IKEv1 pre-shared-key groupkey123
Where is the problem?
Hello
Configuration seems almost perfect. Please share the result of the following of the ASA when you try to connect.
Debug crypto isakmp 200
Debug crypto ipsec 200
You can take snapshots on the external interface of the firewall to confirm if the packets are reaching the firewall or don't use do not:
Kind regards PS Please rate helpful messages.
capture capx off match ip host
Dinesh Moudgil
Tags: Cisco Security
Similar Questions
-
Problem with ASA 5505 VPN remote access
After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?
Here is the cfg running of the ASA
----------------------------------------------------------------------------------------
: Saved
:
ASA Version 8.4 (1)
!
hostname NCHCO
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
network of the NCHCO object
Subnet 192.168.2.0 255.255.255.0
network object obj - 192.168.1.0
subnet 192.168.1.0 255.255.255.0
network object obj - 192.168.2.64
subnet 192.168.2.64 255.255.255.224
network object obj - 0.0.0.0
subnet 0.0.0.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the Web server object network
the FINX object network
Home 192.168.2.11
rdp service object
source between 1-65535 destination eq 3389 tcp service
Rdp description
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0
inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224
outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
LAN_Access list standard access allowed 192.168.2.0 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
outside_access_in list extended access permit tcp any object FINX eq 3389
outside_access_in_1 list extended access allowed object rdp any object FINX
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 649.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0
NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64
NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
the FINX object network
NAT (inside, outside) interface static service tcp 3389 3389
Access-group outside_access_in_1 in interface outside
Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http *. **. ***. 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform
IKEv1 crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHCO group policy
NCHCO group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1
value by default-field NCHCO.local
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username NCHvpn99 password dhn. JzttvRmMbHsP encrypted
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
IKEv1 pre-shared-key *.
type tunnel-group NCHCO remote access
attributes global-tunnel-group NCHCO
address pool VPN_Pool
Group Policy - by default-NCHCO
IPSec-attributes tunnel-group NCHCO
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
ASDM image disk0: / asdm - 649.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
---------------------------------------------------------------------------------------------------------------
And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:
---------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7601 Service Pack 1
Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026
Try to find a certificate using hash Serial.
2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027
Found a certificate using hash Serial.
3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011
RELOADED successfully certificates in all certificate stores.
4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002
Start the login process
5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is NOT behind a NAT device
21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F
SPLIT_NET #1
= 192.168.2.0 subnet
mask = 255.255.255.0
Protocol = 0
SRC port = 0
port dest = 0
45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local
46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710
47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11
49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now
57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">
59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify is set to 28800 seconds
60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***
61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059
IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)
62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025
OUTGOING ESP SPI support: 0xAAAF4C1C
63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026
Charges INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001
Launch VAInst64 for controlling IPSec virtual card
66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034
The virtual card has been activated:
IP=192.168.2.70/255.255.255.0
DNS = 192.168.2.1, 8.8.8.8
WINS = 0.0.0.0 0.0.0.0
Domain = NCHCO.local
Split = DNS names
67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038
Were saved successfully road to file changes.
69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036
The routing table has been updated for the virtual card
71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A
A secure connection established
72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 96.11.251.149. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 192.168.2.70. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001
Did not find the smart card to watch for removal
75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0x1c4cafaa in the list of keys
78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0xc5bfbe3e in the list of keys
80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F
Assigned WILL interface private addr 192.168.2.70
81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037
Configure the public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046
Define indicator tunnel set up in the registry to 1.
83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205276
85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276
88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019
Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205277
91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277
94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205278
96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278
---------------------------------------------------------------------------------------------------------------
Any help would be appreciated, thanks!
try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.
-
No Internet connectivity with ASA 5505 VPN remote access
Hello
I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?
Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.
Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?
I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.
Thank you very much for you help.
Concerning
Salman
Salman
What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.
You have at least 2 options:
-You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.
-You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command
permit same-security-traffic intra-interface
HTH
Rick
-
I recently tried to remove malware on my Vista based laptop Toshiba.
I recently tried to remove malware on my Vista based laptop Toshiba. Malwarebytes helped, but I still have problems with a redirect virus and the refusal by the system to allow me to download various things, Windows Live Mail in particular. I tried to download from a copy of the USB stick to a clean computer, but he still refuses to load telling me to check my internet connection, which is fine for general use. Please help I get crazy and do not forget that I am a pure layman - thank you if you can help - Kidso
I found that the best place to ask this type of question is here: -.
http://forums.ComputerActive.co.UK/forumdisplay.php?f=20
There are some very good people out there who helped me (successfully) on 2 occasions.
Good luck.
I'll be interested to know how you go.
-
Hi allI have the problem with my language of keyboard, the fact is I can't add or remove languages from keyboardWhen I press the keyboard button change that nothing happens, but in the event viewer I get the following messageThe failing application name: Rundll32.exe_shell32.dll, version: 6.1.7600.16385, time stamp: 0x4a5bc9e0Name of the failed module: input.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdf4fException code: 0xc0000005Offset: 0 x 0000000000003756ID of the process failed: 0xf5cStart time of application vulnerabilities: 0x01cd697d57b60837The failing application path: C:\Windows\system32\Rundll32.exePath of the failing module: C:\Windows\system32\input.dllReport ID: 95fbd586-d570-11e1-8bfb-c860006d193aCan someone help me with this? or maybe there's another way to change the keyboard languages? for example through registry?Thanks in advanceI HAVE Windows 7 x 64
Hello
I suggest to create a new user account and check.
Create a user account.
http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account
If the problem does not occur in the new user account, I suggest you to fix a corrupted user profile.
Fix a corrupted user profile.
http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile
-
Hello. I purchased a CS2 product and im having problems with activation. I have the key but my installation failed in the 'summary '. Please help thanks. This is what im seeing.
See my response in audition 3 error with installation
-
Having problems with Adobe Suite C. after the upgrade to El Capitan on an iMac?
Someone at - it problems with Adobe Suite C. after the upgrade to El Capitan on aiMac? What did you do about this? What helped?
In case you downloaded the Apple Stroe Yosemite, it always can be downloaded in the section of your account purchases.
-
I've updated to 2015.2 in September and started having problems with freezing while working on the photos. I upgraded my memory from 4 GB to 8 GB and it has disappeared (in most cases); However, I always feel a lot of questions of export of JPEGs (gel) but not tif files? Very frustrating. Tried to install the new updates but my creative cloud is just a blank page?
Hello
I think you are referring to the white empty window of CC desktop application.
Please refer to the threads below where this issue has been addressed:
Creative cloud is empty window why?
New application Cloud Creative unusable: it is empty!
Re: Empty opening creative cloud app
Kind regards
Sheena
-
Problems with updating creative cloud to desktop. (error code: 2)
Problems with updating creative cloud to desktop. (error code: 2)
Hi Mike,.
You can follow the article: error: "unable to install". Creative Cloud Desktop that will help you get your number sets.
Alternatively, you can follow the thread: Creative Cloud desktop could not be updated. () Error code: 2) where this issue is already addressed.
Let us know if it works or not.
Thank you
Yann Arora
-
Problem with his comments before signing the PDF.
Problem with his comments before signing the PDF.
My problem is with sticky notes that I need to use my comments frequently.
When I place my signature and save document commented, disappear all pop-up windows and icons of sticky notes go "flat" of the document.
It's the same with all the annotation tools and pop ups disappear if I use them with.
Is there a way to keep comments and pop-ups 'living' signing and recording after his comments?
Fig 1: commented the document before you sign and save.
Photo 2: after you save the signed document. Pop - ups disappeared and sticky notes are here to stay.
Hey Tomi,
It was a typo on the part of Ajlan. It was supposed to read "Lock after signing the Document. Please see the screenshot below. However, this check box only appears in the dialog box sign the Document If you sign the last signature on the PDF field. If you don't, it's because there are other unsigned signature fields.
Steve
-
Having problems with SQL Developer connection to the database on a LINUX machine
Having problems with SQL Developer connection to the database on a LINUX machine
Hello
I am trying to connect my machine to windows 7 Home premium to an oracle database 11 g on RedHat 5 machine using SQL Developer. I got this error on SQL Developer
Status: Failed - Test has failed: the network adapter could not establish the connection
on Linux
and TNSPINGLSNRCTL> status Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1))) STATUS of the LISTENER ------------------------ Alias LISTENER Version TNSLSNR for Linux: Version 10.2.0.1.0 - Production Start Date 03-APR-2013 16:13:13 Uptime 7 days 22 hr. 16 min. 41 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File /u01/app/oracle/product/11.2.0/db_1/network/admin/listener.ora Listener Log File /u01/app/oracle/product/11.2.0/db_1/network/log/listener.log Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1))) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=172.X.X.X)(PORT=1521))) Services Summary... Service "PLSExtProc" has 1 instance(s). Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service... Service "orc11g" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... Service "orc11gXDB" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... Service "orc11g_XPT" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... The command completed successfully LSNRCTL>
Tnsnames.ora on Linux,tnsping 172.x.x.x TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 11-APR-2013 14:32:17 Copyright (c) 1997, 2005, Oracle. All rights reserved. Used parameter files: /u01/app/oracle/product/11.2.0/db_1/network/admin/sqlnet.ora Used EZCONNECT adapter to resolve the alias Attempting to contact (DESCRIPTION=(CONNECT_DATA=(SERVICE_NAME=172.x.x.x))(ADDRESS=(PROTOCOL=TCP)(HOST=172.x.x.x)(PORT=1521))) OK (0 msec) [oracle@ltebilling ~]$
Listner on Linux,ORC11G = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 172.x.x.x)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orc11g) ) )
hosts/ect/Linux,SID_LIST_LISTENER = (SID_LIST = (SID_DESC = (SID_NAME = PLSExtProc) (ORACLE_HOME = /u01/app/oracle/product/11.2.0/db_1) (PROGRAM = extproc) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1)) (ADDRESS = (PROTOCOL = TCP)(HOST = 172.x.x.x)(PORT = 1521)) ) )
and there is no problem to ping linux from windows# Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost 172.x.x.x LTEBilling
Published by: user11309581 on April 11, 2013 15:16user11309581 wrote:
as I have already desciped earlier, I can't connect to the server throw Linux my Windows SQL Server, with error message below.
tatus: failed - Test has failed: the network adapter could not establish the connectionIt's too generic to mean anything. The application is hidden the real error message. You got when you did the tnsping and obtained "TNS-12535: TNS:operation has expired. Now THAT's an error.
This indicates a problem firewall and routing. You said earlier you could ping the server, but now we see tnsping fails. Two different protocols of usage, so that both the successful ping turns out a valid physical path, it guarantees not that all traffic will pass. What happens with
c:\ telnet 172.x.x.x 1521
-
Problems with sorting of columns and the number of lines in the report
Hello
I'm having a problem with sorting of columns and the number of lines displayed in a report.
This report displays the data correct, but if I try to sort on a column when I click on the column heading in the report returns no line... I need to click on the "go" button to refresh the report (with the column sorted now) in to display the data.
Similarly, I display only 15 lines per page. If I try to view the lines 16-30, 31-45, etc., that it returns no line until I click on the 'go' button to refresh again.
Has anyone else had (and overcome) the same problem?
Thank you
JosephJoseph,
2 questions:
1) are you using the elements referenced by the report page to filter etc.. ? If so, you're failing values of these when the loading of the page?
(2) are you using PPR page through the results?If so, it could be a problem with the different types of session state, as Anton Nielsen blogged about here:
http://c2anton.blogspot.com/2008/12/Oracle-Application-Express-Apex-three.htmlIf so, you can use calculations or processes to set element values in session state persistent during page rendering, as Anton mentions. In this way, when you use PPR page values will be available in session state and your report should work fine.
Anthony.
-
Is anyone having problems with their Apple Watch since the iOS 10 came to life?
Is anyone having problems with their Apple Watch since the iOS 10 came to life?
Hello
If you have not already done so, it can also help update your Apple Watch to the latest version of the software:
-
problem with my laptop asking for the administrator password or power on password
I have the same problem with my laptop asking for the administrator password or power on password. It is a compaq presario cq61. It happened when my hard drive failed and was not used for a long time. With the password, any help would be much appreciated. It says system turn off after a few trials with the key: 55427586
Hello
Try to enter: 40585508
Kind regards
DP - K
-
My computer recently crashed. A fixed it but! When I then tried to use photoshop I got the message: - message - problem with display driver, temporarily disabled the improvements. Does that mean, they will return when the problem is solved?
Update or restore your graphics driver.
Maybe you are looking for
-
Question about CD/DVD recovery for Satellite A105-s4014
Hi, I need know how to restore or create for this model of toshiba recovery cd/dvd. Thank you.
-
I want to be able to handle the effects of garageband, such as tremolo or EQ, on a single track as it plays (rather than just a "Preset" for the duration of the track), but I don't know if there is a way to do it internally with a single computer. Th
-
24 - n014 envy: install windows Clean 10
So bought this computer yesterday. Love despite the slow HD. No problem. Ill throw in my SSD to my laptop. Now can not activate. No Microsoft Help, no help from Hp other then the cat to call and get help for a fee, or talk to microsoft. The license i
-
Power supply, graphics card
Hi people, I have a model of HP Desktop 6755F, 6 GB of memory, at AMD phenom x 4 9550 Quad-core processor, with integrated ATI Radeon HD 3200. My problem is that I bought a new game recently Silent hunter 5, I have to have all options graphic, turned
-
Install Blackberry pragmatic application.
Hello I'm working on BlackBerry OS 4.5. I want to install another java application of my application. How to install the java application from another java application? Is this possible in silent mode (without informing the USER)?