Process on two hosts

Similar Questions

• Virtual MACHINE running on two hosts after hung vmotion

  Hello

  I started a VMotion of virtual machine by host A to host B. The request got hung at 65% for several hours. I restarted the VCenter service, registered to vsphere. The process was running is longer, but now the virtual machine appears on the Host A and host B.

  The Cluster-'Virtual Machine' tab displays the virtual machine and cycles between two hosts seconds couple?

  Anyone seen this before? How can I fix it? Thanks in advance!

  First of all, it's impossible.  A virtual machine cannot be in 2 places at once.  It's just in the transition.

  Secondly, vCenter manages the process but it doesn't actually do the vMotion, ESX hosts are.

  What is happening is life of the virtual machine on the host only until the end of the evolution towards the other host (somewhere around 97%) when the transfer is confirmed with the new host.

  Best thing to do is to restart the services of management on both hosts and see if that frees the vMotion.

• Travel/cloning between two hosts ESXI VM

  Hello

  I have two hosts ESXI 4.1 with VSphere Essentials for VCenter license. I'm not able to move the virtual machine to one ESXI host to another (power off). It is not supported with VSphere Essentials license? Data warehouses can be shared between the two ESXI hosts?

  What is the size of your virtual machine, what is the speed of the network and how your local storage looks like? Using RAID? How many disks and RAID level? You have a battery attached to the RAID controller write buffer cache?

  The waiting period does not necessarily mean the tasks does not work. Often it is only a delay in the vCenter Server GUI, but the process is still running and you just need to be patient. You see the files being created on the target data store?

  André

• VMotion on two hosts

  We have two hosts and are currently using the same network/vswitch vmotion and vm management.

  I understand that it is best to separate the network for vmotion management.

  (1) may simply run a straight cable between two hosts?

  (2) should the vmotion switch be in a separate network?

  Based on the number of physical network interface cards in your host, instead of connecting the two hosts directly without switch, allows to isolate the vMotion traffic and management VLAN and given that you're going to use a VLAN different you will need a different subnet (network).

• vMotion between two hosts with different version?

  
  Hello

  Can I vMotion VM between two hosts with different version? For example, a virtual machine of esxi 6.0 5.5 esxi and esxi esxi 6.0 5.5 vMotion.

  Thank you.

  Yes, it will avoid you to move.

• vMotion (without shared storage) between two hosts with different vSwitches standard s VM

  I can VM vMotion (without shared storage) between two hosts with different vSwitches standard? The vSwitches on these two hosts have different names and number of NIC, but have the same name of portgroup.

  
  Thank you.

  Yes, you can in a Storage VMotion to one Esxi to another with no shared storage...

  It is important the portgroup bears the same name... This is the reference for the VM...

• Three-node cluster lose two hosts

  In a knot three cluster is it possible to lose two hosts and keep all three data warehouses are still online?

  lol if you lose two guests you don't have redundancy and disconnected data warehouses

• Move a virtual machine to turn off between two hosts, shared storage

  Dear Experts,

  Please guide me for the next case. There are two hosts of Esxi, host 1 is Esxi 4.0 and host 2 is Esxi 4.1. There are store data SAN storage that is visible to both hosts.

  I watched solard winds VM monitor utility that hosting 2 consumes 90% of the memory while its processor is ok. On host 1 is normal. So, I want to spend only a few VM of to host 1. So please correct me if what I think are OK. I will turn off the virtual machine to be moved from host 2. Then I it will remove host 2 inventory. Then on host 1, I'll go to the data store in the folder that VM and do a right click on the file 'say add to the inventory' and now I'm going to see this virtual machine in the inventory of the host list, just turn on and everything is perfect, is this correct?

  Second question on the same hosts, there are a few other data stores that are visible to a host. As if this is the case there is a virtual machine on a data store that is visible to host 2 and I want to spend this VM to host 1 to reduce load on host 2. How to move this virtual machine because this data store is not visible to host 1? Will I have to copy this VM files in a data store that is visible to host 1? If YES then what real required to copy files?

  Kindly help me.

  Kind regards

  From your description I m assuming that you use not vCenter to manage your hosts, correct?

  If you have a store of data shared between two hosts you can do the steps you descripte (power off, remove the inventory etc.).

  For your second case there are several ways, it depends on where you want to place the virtual machine in the future. Wouldn't be on the shared data store that already exists or can in the local data store on the other host? Or is there an option to also display the current data store to host 1?

  If you want to copy the VM files copy the whole folder of it.

  Kind regards

  Mario

• Replication between two hosts

  I have everyone,

  I have two hosts on the same site, in stand-alone mode, but within the same vcenter with licensing standards

  Each host has 3 VMS.

  Is it possible to replicate virtual machines each other on the same VirtualCenter and without cluster?

  Home 1 = VM1 + VM2 + VM3 & [+ VM4 VM5 + VM6 replication]

  Host 2 = VM4 VM5 + VM6 & [VM1 + VM2 + VM3 replication]

  I have enough drive and it will be very safe to run the replicates in minutes in case of problems with a single host.

  Thank you,

  Hello

  If you are using vSphere 5.1, yes you can use Standalone VMware vSphere replication, since vSphere that replication is included in the standard Lincenes.

  http://www.VMware.com/products/Datacenter-Virtualization/vSphere/compare-kits.html

  Short video on the replication of vSphere

  http://blogs.VMware.com/vSphere/tag/vSphere-replication

  See this link for configuration

  http://www.yellow-bricks.com/2012/09/17/back-to-basics-install-configure-and-use-vSphere-replication/

  Concerning

  Mohammed

• How the process in two steps of authentication does not work if you are not in an area of cellular service

  Outside cellular service areas, IS those who know how the two step aunthicatuon process works in an iPhone 6, using the operating system iOS 9.3.4?  Would a being completely locked out of their iphone and apple services until they could find themselves in a cell service area? Or can it be accessed by a public wifi? Who beg to differ on whether or not it is beneficial to use when you travel?

  I did a little research to see if all Apple items shed light...

  See "How it works" in the Apple ID - Apple Support for two-factor authentication - a time that a device is approved, he'll never ask again unless you perform one or more of several things to "break the connection.

  If I were you, I would spend it TURNED off if you fear that one of these things could happen while you might not be able to obtain the code by SMS

  Frequently asked questions about the audit in two steps for Apple ID - Apple Support

  I'm confused as to why Apple would use two different expressions for what seems to be the same:

  • "Two -authentication"- and
  • "Two -step".

  The above two articles begin with a statement like: [underlining is unique, "BOLD" is synonymous with]

  "Two-factor authentication is just an extra layer of security of your ID Apple aiming to sure you are the only person who can access to your account, even if someone knows your password."

  «The two-step verification is an additional security feature for your Apple which designed to prevent anyone to access or use your account, same ID is they know your password.»

  Maybe someone with more experience can shed some light on your question and MY confusion?

• A r420, a Md3220, but two hosts in the Dell software

  The r420 has two cards dell inside 6Gbs SAS. Under "Default group", it lists 'host EMFPCROSBN12' and which is mapped to 'access' (under EMFPCROSBN12 properties, it lists several SAS addresses, I know nothing of) but another host is listed, this seems to correspond to the two SAS cards, under properties, it lists two addresses of sas which refer to those two sas cards). There are also 'access' and all the virtual disks that I created during installation. Anyone know what that 'host EMFPCROSBN12 '?

  I've seen similar names on new systems. I think it's a Dell test system of until they ship the MD3200 of the plant (and they don't seem it clearly indicates the registered Listehotes parameter).

• Two hosts w / same Unique identifier

  I have a situation where two different hosts show the same Unique identifier.

  I get the following error in Foglight:

  

  Also, I get the following error message when you try to start the FGLAM on the host:

  

  Here is the Unique identifier for the host brprwast001 name:

  

  Here is the Unique identifier for the host name okwprdas01:

  

  Just make sure, how did this happen? have you copied an installation from one host to anthoer or was it a name change?

  In any case, the message that you get when you try to start the fglam made you in the right direction. Now you have the display name host with the same value on 2 machines, you must go to the installation directory of fglam under State/default/config, you should have a fglam.config.xml, make sure that each host has the right poster name and they are different. If the host has changed its name, there is also a variable on the reports of a warning when the name changed (which you probably want to set to false).

  I hope this helps.

  Golan

• VLAN between two hosts ESXi

  Hello

  I have two virtual machines based on VMware and some configuration of VLAN

  VM1 - VLAN 130 on ESXi01

  VM2 - VLAN 135 on ESXi02

  For example, a machine of vlan ESX1 130 cannot ping a VM one another in the vlan ESX2 130. But if I move the ESX1 second VM, it works.

  VM1 im going through vSwitch 130 VLAN via the ESXi01, what's happening than ESXi via vmnic11 port Vethernet910 on FABRIC

  FABRIC-001-B # connect nxos
  Operating system (NX - OS) Cisco Nexus software
  TAC support: http://www.cisco.com/tac
  Copyright (c) 2002-2014, Cisco Systems, Inc. All rights reserved.
  The copyright in certain works contained in this software are
  owned by others and used and distributed under
  license. Some components of this software are licensed
  the GNU Public License (GPL) version 2.0 or GNU
  Lesser General Public License (LGPL) Version 2.1. A copy of each
  This license is available at
  http://www.opensource.org/licenses/GPL-2.0.php and
  http://www.opensource.org/licenses/LGPL-2.1.php
  Fabric-001-B (nxos) # sh ver

  Operating system (NX - OS) Cisco Nexus software
  TAC support: http://www.cisco.com/tac
  Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_h...
  Copyright (c) 2002-2014, Cisco Systems, Inc. All rights reserved.
  The copyright in certain works contained in this document are the property of
  other third parties and are used and distributed under license.
  Portions of this software are covered by the GNU Public
  License. A copy of the license is available at
  http://www.gnu.org/licenses/gpl.html.

  Software
  BIOS: version 3.6.0
  Charger: version N/A
  Kickstart: version 5.2 (3) N2(2.21c)
  system: version 5.2 (3) N2(2.21c)
  power-seq: Module 1: version v2.0
  Module 2: version v1.0
  Module 3: version v2.0
  uC: version v1.2.0.1
  SFP UC: Module 1: v1.1.0.0
  Compile of the BIOS time: 09/05/2012
  kickstart image file is: bootflash:///installables/switch/ucs-6100-k9-kickstart.5.2.3.N2.2.21c.bin
  Kickstart compile time: 05/02/2014 11:00 [05/02/2014 19:47:41]
  filesystem image is: bootflash:///installables/switch/ucs-6100-k9-system.5.2.3.N2.2.21c.bin
  compile time: 05/02/2014 11:00 [05/02/2014 21:42:39]

  Material
  Cisco UCS 6248 series fabric of interconnection ("O2 32X10GE/Modular universal platform supervisor")
  Intel Xeon CPU with 16553964 k of memory.
  Processor Board ID

  Device name: FABRIC-001-B
  bootflash: 31266648 kB

  The availability of the core is 147 day (s), 15 hour (s), 15 minute (s), 46 second (s)

  Last reset
  Reason: unknown
  The system version: 5.2 (3) N2(2.21c)
  Service:

  plugin
  Core Plugin Ethernet, Fc Plugin, Plugin, Plugin of virtualization
  Fabric-001-B (nxos) #.

  on NXOS, I see

  See the fabric-001-B (nxos) # run interface vethernet 910

  interface Vethernet910
  Description 1/3 Server, VNIC VNIC9
  switchport mode trunk
  switchport trunk allowed vlan 1 108-109 115-119 150 - 151
  pinning Server sticking border-interface port-channel13
  pinning of pinning-down server drop down link
  queues of default entry - type service-policy policy
  bind the interface port-channel1282 910 road
  no downtime

  and information portchannel

  Fabric-001-B (nxos) # sh port-channel summary
  Flags: D - low P - Up in the port-channel (members)
  I - individual H - standby (LACP only)
  s suspended r - Module-removal
  S - Dial R - routed
  U - up (port-channel)
  M not in use. Min-links not met
  --------------------------------------------------------------------------------
  Group-Type Port Protocol Ports members
  Channel
  --------------------------------------------------------------------------------
  11 Po11 (SU) Eth LACP Eth1/15 (P) Eth1/16 (P) Eth1/31 (P) Eth1/32 (P)
  13 Po13 (SU) Eth LACP Eth1/14 (P) Eth1/30 (P)
  1280 Po1280 (SU) Eth NO Eth1/1/13 (P) 1/Eth1/14 (P) 1/Eth1/15 (P) 1/Eth1/16 (P)
  1281 Po1281 (SU) Eth NO Eth1/1/1 (P) Eth1/1/3 (P)
  1282 Po1282 (SU) Eth NO Eth1/1/9 (P) Eth1/1/11 (P)
  1283 Po1283 (SU) Eth NO Eth1/1/5 (P) Eth1/1/7 (P)
  1284 Po1284 (SU) Eth NO Eth2/1/1 (P) Eth2/1/3 (P)
  1285 Po1285 (SU) Eth NO Eth3/1/1 (P) Eth3/1/3 (P)
  1286 Po1286 (SU) Eth NO Eth3/1/5 (P) Eth3/1/7 (P)
  1287 Po1287 (SU) Eth NO Eth3: 1/9 (P) Eth3/1/11 (P)
  1288 Po1288 (SU) Eth NO Eth3/1/13 (P) Eth3/1/14 (P) Eth3/1/15 (P) Eth3/1/16 (P)
  1289 Po1289 (SU) Eth NO Eth4/1/1 (P) Eth4/1/3 (P)
  1300 Po1300 (SU) Eth NO Eth1/1/17 (P) Eth1/1/19 (P)

  I have lack of VLAN, how can I edit and update the information of vlan?

  Of UCS Manager? I don't have 1000v.

  Hello

  To add VLANs, you must go to the LAN tab, create them and after that, add them to the vNIC of blades you want to pass traffic for that/those support VLAN.

  You have configured a VLAN in UCSM native?

  The two, ESXi01 ESXi02 & use the same fabric for interconnection to pass traffic?  If a host goes through A traffic and the other through B, traffic will need to visit the switch upstream as cause of tissue switches do not switch traffic between them.

  Try the commands below and paste it here:

  * show circuit of service X Server profile / Y< chassis/server="" in="">

  * Connect nxos one | b< first="" try="" "a"="" then="" "b"="" and="" the="" output="" of="" the="" below="" command="" for="">

  * sh pinning border-interfaces

  * See the platform flexible NHS inter vlandb of info id #.< "#"meaning="" the="" vlan="">

  -Kenny

• Process in two different tables in one page

  Hi all

  I have A form with a submit button, when I click on the button I want to send the data from two different tables. For example:

  REQ_ID: 221

  BOX_NUMBER: 2

  NOM_ELEMENT: APPLE

  COUNTRY_ORIGIN: USA

  I want to send all the information in table 1 and only REQ_ID and BOX_NUMBER in table 2.

  I tried to create processes two different which are:

  1. the usual process line DML for table 1 and;

  2. simple query 'Insert' SQL for table 2

  It seems fine, until I realized that when the user tries to update the BOX_NUMBER to 10 for example, only 1 table is updated and table 2 creates an another duplicate data instead of updating the old one! This also applies to my button Delete,.

  any idea to fix this problem?

  Thank you very much

  Vika

  Reread what you wrote and you would realize why 2nd table only "new lines".

  2. simple query "Insert into ' SQL for table 2

  If you need to UPDATE the table, then you must write a simple UPDATE statement.

  If you want to REMOVE from the table, then you must write a simple DELETE statement.

  I call this "DML DIY" - do it yourself DML

  (personally, I'd probably use MERGE for INSERT and UPDATE)

  MK

• Communication between two hosts on the host only

  I have a host ESXi 5.5 with two reviews, a Linux / Centos 6.5 comments and a guest Server R2 2012.

  I've muddled through many questions - time zone, being the biggest problem, but am confused on how to get these guests to see one another, not even sure what to put in Google.

  My goal is to be able to share files between the two guests and access their consoles with putty and RDP, but I can't make them one ping to another. Everyone on the LAN can connect these two guests, but they cannot see.

  A kind soul told me that I forgot?

  Thank you

  Hey katycomputersystems,

  Could you give us a quick screenshot of your vSwitch / Port groups.

  Of the IP information you should be able to ping to each of the systems if they are on the same vSwitch / Portgroup / VLAN.

  Try this

  vSwitch0

  VM Network - Port Group - VLAN 110 - physical Nic don't matter we will keep all the VMS on this port group

  Configure all your VMS on the port network of VM group.  As long as all the VM living on the same port group vlan and vSwitch traffic should never leave this vSwitch and each VM must be able to communicate with each other.  If not you can always ping each other take off the VLAN and try again.  Make sure also that you have no firewall or tables ip enabled on the operating systems that could prevent communication.

  Let us know how it goes