PS-1100 manual

Similar Questions

• Pavilion g7t-1100: Internal Microphone does not work do not on HP Pavilion g7t-1100 after winning 10 update

  Can someone (1) confirm that this model of laptop computer has an internal microphone and (2) say how to operate?

  Story:

  I've had this laptop for several years with Win 7 64 bit, recently upgraded to win 10 64-bit edition.  When you run Windows 7, I've certainly used an external microphone with the Jack, but I'm not sure I've ever used the internal mic.  Yesterday I tried to use Skype and couldn't get the microphone to work (I don't have an external mike where I am now).  Started trying to analyze and the only peripheral record listed in the recording of the sound control Panel tab is "Stereo Mix, IDT High Definition Audio CODEC" - don't know if this applies to the internal mic.  Speaking to, or by tapping on the hole of the microphone above the display caused no response at all in the level to the right of the window bars.

  Began to doubt that I have an internal mike, so looked up specifications.  On http://support.hp.com/us-en/document/c02910495, I found "Webcam with integrated digital Microphone (VGA)", which led me to go on webcam integrated under imaging devices.  Still no final confirmation that I have a mike internal, but I found a laptop computer with mike identified next to the webcam image, this corresponds to my laptop, so I really think that the material is there.

  I used Device Manager to check the updates for the device webcam (HP Webcam-101), and he says that the drivers are up to date.  I did the same thing for the IDT High Definition Audio CODEC, also updated.  I think that the drivers have been updated when I upgraded to win 10 in February.

  That's it - information or suggestions are welcome.

  Hi there @BruceBon,

  Thank you for visiting the Forums HP's Support and welcome! I read your message on the HP Support Forums and see that you are having problems with the microphone on your HP Pavilion g7t-1100 CTO Notebook PC.

  The reason why you can't find loads or User Guides/Manuals books appropriate because the model you have is a laptop CTO, this means it is customized/configured to order. Where did you get to buy your laptop?

  When I went to the Service Guide and HP Pavilion G7 maintenance (generic), it shows an internal microphone located at the top of the LCD, but again, your laptop is a CTO model this is why there is no specification of final product because each of them can be customized.

  You can try to look over some of the screenshots in the microphone troubleshooting document. There are a few sections of this document that you can try.

  • Using the troubleshooting tool
  • Check the settings of the sound
  • Rise in the level of the microphone volume

  If you right click you see him show disabled devices and display devices disconnected in the recording of the Properties tab?

  They have check marks next to them?

  This answer doesn't solve your problem or answer your question? If so, please share the good news! Inform others that this answer was helpful by clicking on the button accept as a Solution . You can also show your appreciation by clicking thumbs-up.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems, and where you bought your laptop from.

  Have a great day!

  Thank you!

• HP laserjet 1100: laserjet 1100

  Hi, I'm Italian I have a hp laserjet 110, I went from the OS WINDOWS XP to Windows 7 Home Premium (32 BIT), I lost the printer driver and you don't have the installation CD. Can someone please help me, also in English.
  Happy new year everyone thank you
  KASKO

  You use the same computer?  Newer computers often do not have a parallel port.

  Windows 7 should be the base for this printer drivers.  It uses a simple command language print.  When it is connected to your computer, go to install a new printer.  You may need to find manually through the library of Windows because most directly connected printers this old will not visible to the computer until the pilots will seek.  It should take only a few minutes.

  If all else fails...  AND if you do not have a parallel port...  Go to the HP website and search for the software and drivers for 1100 drivers.  If you can't find them there, check for any PCL5 driver.  Download it and let it find the printer.

  I hope this helps.  Write back if you get stuck.

  I was at Roma and Santa Marinella.  Love them both!

• HP Mini 210-1100: HP Mini 210 1100 - product Microsoft Windows 7 under "vanity cover" but where is this coverage?

  Hi, I have a laptop of HP Mini old (circa 2010) 210-1100, he is real sweet and small.  Errors at startup, it looks like the drive disappeared.  I would find the product key of Windows 7 and see if I can find the ISO to restore on a new drive, maybe an SSD.  The bottom of the laptop says product key is in the compartment batteries or the cover of the vanity, is not in the battery compartment and I see nothing that matches this coverage "vanity", any ideas. ?

  Cheers, David-SB

  

  @David-SB

  Click on Maintenance and Service Guide.

  http://support.HP.com/ph-en/product/HP-mini-210-1100-PC-series/4151684/manuals

  Start on page 40.

  REO

• Accuracy of measurement of the SCXI-1100 module

  Dear team,

  I'm figuring an accuracy of measurement for SCXI-1100 (http://digital.ni.com/manuals.nsf/websearch/0790D3C92CF4B16E8625665E00712865) devices.

  It is not described in the standard table, it has precision stage of entry / exit (must be added?). I can't reach a precision which is a result of precision calculator. If you have any equatuions / examples please post.

  Concerning

  Michal

  Hi Michal,

  I'm not sure I understand your question. Are you trying to calculate the accuracy of the SCXI-1100 module, but you do not have the data specification for the calculation, or you don't know how to calculate the accuracy?

  If you need performance data, you can consult the technical data sheet 1100 SCXI. If you want to calculate your accuracy of the device, I can recommend you following KB: How can I calculate absolute precision or the accuracy of the system?

  I hope that this is the info you are looking for.

  Kind regards

  D. Barna

  National Instruments

• using scxi 1303 and 1100 to measures of pressure

  Hello

  I use the scxi 1303 and 1100 to measure the voltage inputs. Specifically, I have 8 voltage at 0 - 10 v and 9 measures of pressure to 4-20mA, converted to signals 1 - 5V with a 250 Ohm resistor.

  My arrises now question about pull upward resistance. I don't have resistance inserted (as the manual leads me to believe that they are not necessary). My arrises now problem of a difference in the voltage across the resistance (the same as the display of pressure transmitter) and the voltage displayed by Labview.

  For example:

  Voltage = 1.47 V

  LabVIEW display = 1.18 V

  1303/1100 Setup requires it resistance of 10 ohms, or don't you think that something is happening?

  Thank you and please forgive me if this question has been addressed!

  Good news... After much stable, time and tears I have solved the problem. I have indeed had a hardware issure. The module SCXI-1100 I used was broken somehow and was replaced by a functional SCXI-1102.

  Thank you for helping me think about troubleshooting ideas!

• Upgrated dm4t-1100 with 256 GB ssd drive

  Hello

  I want to improve my storage unit with a 256 GB SSD:

  (a) 256Go crucial m4 2.5 inch Solid State Drive SATA 6 Gbps

  or

  (b) OCZ Technology 256 GB 4 Vertex Series SATA 6.0 GB/s 2.5 - Inch solid state drive

  1. number and product name

  Pavilion dm4t-1100

  2 operating system installed (if applicable)

  Windows 7 64 bit

   

   

  I updated the bios of my laptop via hp web page; and I don't know if there is a problem with high capacity ssd 256Go, could be a problem for this old laptop? I need to something another special update or a player?

  and that could be the best unit ssd ( Crucial 256 GB 2.5 m4 or OCZ Technology 256 GB Vertex 4 Series 2.5 inches)

  Thank you

  Hello

  Your laptop supports only the connection SATA II is a bit useless to buy any SATA III SSD that they will operate as SATA II disks. The service manual indicates that DM4 laptop support SSD 160GB drives, so all SSD should work as I do not think that the ability is a limit. OCZ, Intel, Corsair and a few others have good readers then choose one of the series SATA II of these manufacturers. I've seen some cases that a SATA III SSD did not work but a SATA II we did on older laptops. Maybe the newer controllers SATA and the old BIOS may cause some compatibility issues...

• Network card wireless upgrade dm4t-1100?

  HI -.

  I read a few threads asking if a specific card will work in this model, but I'm going to be less accurate. I have a computer dm4t-1100 HP laptop running Windows 7, it is the only Windows machine I have left and one of the reasons why I always use it to resolve WiFi issues with inSSIDer. The problem is the stock WiFi does that 2.4 GHz, and I would like to have a portable device that can run inSSIDer and do 5 GHz.

  Y at - it a replacement of WLAN card that will make A/B/G/N 2.4 & 5 GHz? (I'm sure that it's too ask

  If there is, can I replace it myself or is there a 'white list' or another problem, I will also have (read some of the threads that indicate this is a problem?).

  Are there "generic" cards, can I buy it from Amazon for it, or even only a 'white list' feature I need HP?

  Thanks for any help you can offer, I would prefer not to conduct just a USB that I tend to break or lose things like that.

  -Bruce

  Hi, Bruce:

  Here is the link to the service manual for your laptop.

  Chapter 3 lists the cards wlan supported with HP part numbers.

  http://h10032.www1.HP.com/CTG/manual/c03106715.PDF

  I do not believe that the adapter WiFi Atheros AR9285 802.11 a/b/g/n 2 x 2 is a dual card band even though it is listed as such.

  The parts store shows as a card bgn.

  So, as I see your choice is if you live in the United States...

  Broadcom 43224AGN 802.11a/b/g/draft-n WiFi adapter HP Part # 582564-001

  Intel® Centrino® Advanced-N + WiMAX 6250 HP part # 619997-001

  The only cards that work are those indicated in the maintenance manual and they must have the part number HP on them or won't work, because of the white list of the BIOS.

  I recommend buying a used but tested and working one on eBay by questioning by the part number.

  They can be had at bargain prices.

• I have remove the IOS of the aironet 1100 series by mistake and now I need to copy the IOS image file

  Hello

  I have a cisco aironet 1100 Series wireless access point.

  by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.

  I need your help please.

  For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).

  I downloaded the file c100-k9w7 - mx.123 - 8.jed

  and I download the tftp (tftpd32) servers

  I have the router connected directly to a pc with the static ip address of 10.0.0.2

  but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.

  and by a tftpd32 I try but no function.

  I don't know what I'm doing wrong.

  other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.

  Thank you.

  I'll wait your hepls.

  Convert a standalone Lightweight Access Point
  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272

• backlight on the keyboard for HP Envy 4 t-1100

  Hey

  I just bought a new HP Envy 4 t-1100 laptop and I want to replace the keyboard of a keyboard backlight, cant find anywahere to buy one and also I can not find a manual on this laptop on how to replace it?

  I found a HP Envy 14 keyboard, it will work with my HP Envy 4 t-1100?

  UM, I just tried to walk though the payment process and it seemed to work. If you are still having problems I go ahead and contact HP support. They will be able to order the part for you. You can contact the parts department at: 1-800-227-8164

  -Sean

• Dell Dimension 1100

  Don't think that lightning strike twice in the same place.  A few weeks ago, lightning struck close enough to home to fry my workstation 220 motherboard and modem from Comcast.  The same thing happened about this time last year.  Both times, it was close enough to feel the concussion on the INSIDE of the House.

  My fallback position is a Dimension of 1100, which transfer parts in the deceased workstation.  Because it'll be awhile before I can rebuild the work station, I decided to put both hard drives in the Dimension.  Of course, there is a tray for a single.  The second hard drive is now in the space for the second CD/DVD, and it just seems unprofessional.

  Is there a Dell tray for two hard drives which falls in the case of the Dimension 1100?  There is an adapter two parts available, but it looks like a two-piece adapter, not a part of Dell.

  Thomas Johnson

  Thanks for the reply, but I have an OT962 tray in the machine and another on the way to eBay.  My other significant says when she doesn't understand me, it's because I can't explain right.  So... Let try me again.  I put the two OT962s with a kind of clamps, but by doing this, it'll take a bit of work to do and undo, if I need or that you want to remove a hard drive.  Apart from a hole in the chassis, for the screw that holds the second OT962 in place.  I was hoping to find a single pan to keep the TWO drives in place, one that just fits into the Dimension 1100 and screw up 'easy peasy'.  I have maybe just bite the bullet and make the clamping shtik.  I'll let you know how it works.  Thank you, again.

  J.

  Thomas Johnson

  As far as I know, a Dimension 1100 'Double Hard Drive Tray"has never been made, either by Dell or any third party parts manufacturers.

  Because the Dimension 1100 uses a chassis of MITAC ATX as Dimension 4600 and the Dimension 2300/2350/2400/3000/4700/1100, you can use the same instructions to install the hard drive platters, see pages 17 & 18 here:

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-4600_service%20manual_en-us.PDF

  Bev.

• from readers require manual connect

  We organize several vaults file AFP/SMB interview about 30 workstations, which now require manually hit 'connect' on the window of connection for each server. We checked the username/password to inhabit the keychain of the local machine (that we don't store the trousseau on the cloud), and all drives are listed in user "Login Items" list. This issue was not a problem on El Capitan, or earlier.

  Thanks in advance

  This question was for the first time in the beta versions of Sierra. It was not fixed at the time of the release. Maybe it will be fixed in an update of the Sierra...

• How to manually lock iwatch with last software update

  The last update, I am unable to manually lock my iwatch

  Hello

  To manually lock Apple Watch under watch OS 3:

  • When you display the time on your watch, drag upward on the screen to open the control center > press the button with a lock icon to lock your watch (you may need to scroll to see it).

• Thunderbolt manual bridge IP no longer works with Sierra

  I use a Thunderbolt bridge with manual IP connection to connect 3 mac to my main MacPro, since the update of Sierra I can't connect one of the mac via the manual / plus static IP.

  Please HELP, am I missing something? It has worked before and now it no longer work.

  Joe

  Anyone?

  My work is stationary, and my staff is looking at me.

  Help, please!

  I also note that since the Sierra update whenever I connect to the server via the LAN cable or stroke, it appears this box, -that use only to appear only once (when I put in place) and hten again, unless I have re - install the operating system.

  Perhapse it is a new way to set up an IP Maunaul or I've never done right. Help, please.

  I pay my staff to do nothing right now.

• Setup Airport Express: how to manually set the IP address and DNS?

  I just bought an Airport Express for the wifi in the ethernet cable that I have in my dorm room.

  To connect to the internet via the ethernet cable, I need to enter a number IP, DNS, gateway and mask provided by the dorm (as I did on my Macbook).

  The problem is that I don't see where I can do for the Airport Express. After I plugged the cable into it, it keeps wanting to configuration alone, which does not work (he's trying to "join the network" forever, without success).

  How can I configure IP, DNS etc. manually?

  Thank you much for the help

  Hello!

  I read the post and found article suggested for her: OS X El Capitan: connect to the Internet or a network using Ethernet

  Thank you!