Remove the vDS Teddy

Similar Questions

• Remove the host vDS

  Hello

  Somehow I lost connectivity between vCenter and vSphere host. Then I run esxcfg-vswitch - l and I could see a vDS I had previously throug vDS switch config on vCenter. I tried to remove it with the esxcfg-vswitch command but I went out: "No such virtual switch" although I see when I run the command 'esxcfg-vswitch - l ". Is it possible to delete this item because my vswif0 is not accessible more I got it as a grouped under Port Group vDS and vDS (vmnic0 and vmnic1), but now I can't access it. Are there any command line for vDS?

  Thanks in advance

  Please see the best documents referred to vDS migration:

  The recovery to an ESX host procedure involves moving from vswif to a new temporary vs management interface. Access to the server management is necessary thanks to ILO or KVM physically connected to the server interface. After the management of connectivity is estored, use the vSphere Client to continue setting up virtual network.

  Step 1: Connect to the ESX host.

  Step 2: Create a new temporary vSS (tmpSwitch) and the port (vswifPg) group

  esxcfg-vswitch - a tmpSwitch

  esxcfg-vswitch - a tmpSwitch vswifPg

  Step 3: Move the uplink of vDS to vSS

  esxcfg-vswitch - l (to get names DVSwitch, DVPort and vmnic)

  esxcfg-vswitch - Q vmnic0 v < dvPort > < dvSwitch > (untie the vDS vmnic0)

  esxcfg-vswitch - L vmnic0 tmpSwitch (link to vswitch)

  Step 4: Move vswif to vDS in vSS

  esxcfg-vswif - l (get vswif IP address, netmask, dvPort id, etc.)

  esxcfg-vswif vswif0 d

  esxcfg-vswif - a n-i < ip address > < vswifPg > Pei netmask vswif0

  Check or change the default gateway address editing sysconfig or add gateway address by default with:

  route add default gw < gateway address >

  vcbMC - 1.0.6 Beta

  Lite vcbMC - 1.0.7

  http://www.no-x.org

• Cannot remove vCenter vDS 5.5

  Hi all

  I am trying to remove a switch distributed the vcenter but it comes up with an error message box:

  «vDS SW-DCN-C1_C2 port c-40 is used by the entity < not found.» "> Virtual NIC 4000, type: vmVnic.

  I remove all the groups from ports and I remove all the hosts and vm that were connected to vds.

  I move down, all the vds and c-40 port id to "Unused uplinks" dvUplink in consolidation and failover policies.

  What otherwise I can do?

  Thanks for the help everybody.

  You can remove the entry from vCenter Database its under vpx_entity

  Run the script in management studio below if you are using the MSQL.

  Select * from VPX_ENTITY by name;

  Search for the name of the object that is DVswitch and get the ID of the object and remove it by running the script.

  get involved DB admin to run the script.

  take a snapshot of the vCenter if VM is a virtual machine and a backup of the DB

  If the object is not found even in DB, try to remove it from vCenter MOB.

  https://VC.FQDN.com/mob

  This will help for sure.

  I had the same problem once.

  in my case the DvSwitch has been removed, but the uplink remained in vCenter view

  When I tried removing it (object cannot be found)

• Remove the ' system VLAN "Nexus 1000V port-profile

  We have a Dell M1000e blade chassis with a number of Server Blade M605 ESXi 5.0 using the Nexus 1000V for networking.  We use 10 G Ethernet fabric B and C, for a total of 4 10 cards per server.  We do not use the NIC 1 G on A fabric.  We currently use a NIC of B and C fabrics for the traffic of the virtual machine and the other card NETWORK in each fabric for traffic management/vMotion/iSCSI VM.  We currently use iSCSI EqualLogic PS6010 arrays and have two configuration of port-groups with iSCSI connections (a physical NIC vmnic3 and a vmnic5 of NIC physical).

  We have added a unified EMC VNX 5300 table at our facility and we have configured three VLANs extra on our network - two for iSCSI and other for NFS configuration.  We've added added vEthernet port-profiles for the VLAN of new three, but when we added the new vmk # ports on some of the ESXi servers, they couldn't ping anything.   We got a deal of TAC with Cisco and it was determined that only a single port group with iSCSI connections can be bound to a physical uplink both.

  We decided that we would temporarily add the VLAN again to the list of VLANS allowed on the ports of trunk of physical switch currently only used for the traffic of the VM. We need to delete the new VLAN port ethernet-profile current but facing a problem.

  The Nexus 1000V current profile port that must be changed is:

  The DenverMgmtSanUplinks type ethernet port profile

  VMware-port group

  switchport mode trunk

  switchport trunk allowed vlan 2308-2306, 2311-2315

  passive auto channel-group mode

  no downtime

  System vlan 2308-2306, 2311-2315

  MGMT RISING SAN description

  enabled state

  We must remove the list ' system vlan "vlan 2313-2315 in order to remove them from the list" trunk switchport allowed vlan.

  However, when we try to do, we get an error about the port-profile is currently in use:

  vsm21a # conf t

  Enter configuration commands, one per line.  End with CNTL/Z.

  vsm21a (config) #-port ethernet type DenverMgmtSanUplinks profile

  vsm21a(config-port-Prof) # system vlan 2308-2306, 2311-2312

  ERROR: Cannot delete system VLAN, port-profile in use by Po2 interface

  We have 6 ESXi servers connected to this Nexus 1000V.  Originally they were MEC 3-8 but apparently when we made an update of the firmware, they had re - VEM 9-14 and the old 6 VEM and associates of the Channel ports, are orphans.

  By example, if we look at the port-channel 2 more in detail, we see orphans 3 VEM-related sound and it has no ports associated with it:

  Sho vsm21a(config-port-Prof) # run int port-channel 2

  ! Command: show running-config interface port-canal2

  ! Time: Thu Apr 26 18:59:06 2013

  version 4.2 (1) SV2 (1.1)

  interface port-canal2

  inherit port-profile DenverMgmtSanUplinks

  MEC 3

  vsm21a(config-port-Prof) # sho int port-channel 2

  port-canal2 is stopped (no operational member)

  Material: Port Channel, address: 0000.0000.0000 (bia 0000.0000.0000)

  MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  Port mode is trunk

  Auto-duplex, 10 Gb/s

  Lighthouse is off

  Input stream control is turned off, output flow control is disabled

  Switchport monitor is off

  Members in this channel: Eth3/4, Eth3/6

  Final cleaning of "show interface" counters never

  102 interface resets

  We can probably remove the port-channel 2, but assumed that the error message on the port-profile in use is cascading on the other channel ports.  We can delete the other port-channel 4,6,8,10 orphans and 12 as they are associated with the orphan VEM, but we expect wil then also get errors on the channels of port 13,15,17,19,21 and 23 who are associated with the MEC assets.

  We are looking to see if there is an easy way to fix this on the MSM, or if we need to break one of the rising physical on each server, connect to a vSS or vDS and migrate all off us so the Nexus 1000V vmkernel ports can clean number VLAN.

  You will not be able to remove the VLAN from the system until nothing by using this port-profile. We are very protective of any vlan that is designated on the system command line vlan.

  You must clean the canals of old port and the old MEC. You can safely do 'no port-channel int' and "no vem" on devices which are no longer used.

  What you can do is to create a new port to link rising profile with the settings you want. Then invert the interfaces in the new port-profile. It is generally easier to create a new one then to attempt to clean and the old port-profile with control panel vlan.

  I would like to make the following steps.

  Create a new port-profile with the settings you want to

  Put the host in if possible maintenance mode

  Pick a network of former N1Kv eth port-profile card

  Add the network adapter in the new N1Kv eth port-profile

  Pull on the second NIC on the old port-profile of eth

  Add the second network card in the new port-profile

  You will get some duplicated packages, error messages, but it should work.

  The other option is to remove the N1Kv host and add it by using the new profile port eth.

  Another option is to leave it. Unless it's really bother you no VMs will be able to use these ports-profile unless you create a port veth profile on this VLAN.

  Louis

• removed the audio tracks in logic pro can be restored

  removed the audio tracks in logic pro can be restored, has been save logic & empty folders to the folder came, I deleted the originals by mistake...

  Not if you don't have the original audio files on your hard drive.  If you have deleted original, your only hope he then restore from a backup of your system, you have a.

• How can I download apps using iOS iPhone 5 s 10 and a waterproof case (without removing the case each time!)

  I have an iPhone 5 s protected by a waterproof case, secure screw using Allen.

  This command removes the possibility of using the ID of the contact.

  Contact ID is required by the App Store!

  I found a way around locking the screen, but not found how to circumvent App Store

  Have you disabled the following: settings > Touch ID & password > iTunes and App Store?

• How can I delete an email from apple mail after removing the content (by virus scan software?)

  Recently, I received an avalanche of emails with malicious attachments.  I have not opened any of the accessories, and my antivirus software has picked up malicious content and removed from the email.  Thus, I find myself with an email on my system, no content.  Unfortunately, the system does not allow me to then remove the (s) e-mail that is left.  How can I remove these 'empty' emails in my Inbox mailbox?

  ... my antivirus software has picked up malicious content and removed from the email.

  Allowing something to edit the database of e-mail will result by it becomes corrupted.

  If you use Time Machine, restore the email by "entering Time Machine" of in Mail and choose a time to restore. Then, just delete suspicious e-mails in the usual way. Exit full screen before entering Time Machine.

  You may not use software "anti-virus" not Apple on a Mac, for this reason and many others. Identify the product you use to get the uninstall instructions.

• Remove the entries in the playlist.

  I can't get rid of unwanted entries in the playlist.  There is no x in the top right and the items won't slide.  I'm on Yosemite 10.10.5

  Highlight the item in the playlist column.  Hold down the CTRL key.  Click on the item and options pop up.  Select remove the element.  Yes I know.  Why they have just under the X in the corner?

• You can remove the gaps between songs in itunes 12.5.1.21

  How can I remove the gaps between songs itunes 12.5.1.21

  Unfortunately, user control in playback gapless disappeared several years ago.  There are different things you can try. You can use a different ripper to rip tracks omitting gaps (see XLD).  You can set crossfade overlap packed during the silence between tracks.

• Change the orientation of the mouse. Click the apple icon, and then select check box on the left. However, this box is covered by a video on the use of the mouse. How to remove the video?

  Change the orientation of the mouse.  Click the apple icon. System Preferences; OK to this point; the area to select 'Left hand' is covered by a video on the use of mouse clicks. How can I remove the video (s) so I can't select 'Left hand' in the box?

  System Preferences > mouse, and then select the tab more moves.

  Then on the left, select: slide between pages

  Click scroll left or right with one finger , and then make your choice.

  You cannot delete the video. This is a demonstration.

• Under settings &gt; how to remove the storage data

  I went into settings > storage & use iCloud and I want to know how to delete data. For example in my mail application my iPad tells me that there are 796 MB. I emptied my Inbox, trash and sent the messages. Why is there so much use? In iMovie, I show 621 MB, that I do not use iMovie. How can I delete cache in my ios device?

  The simplest thing to try is a reset.  Press and hold the power and home together for 10 seconds until the Apple logo appears.

  That may well help your storage numbers.  If this is not the case, try a restore or remove the email account and reintroduce.

  Restore your iPhone, iPad or iPod touch from a backup - Apple Support

• How to remove the curtain of the screen when the watch is not matched

  How can I remove the curtain of a unmatched watch screen?

  Follow the instructions in this discussion > How to disable screen curtain when iWatch not more paired with iPhone?

• Remove the old Apple ID

  My App Store won't let me update my applications... He said: I need my old Apple ID and I have not used this ID in a long time... And I made a new Apple ID a few months ago... And my App Store is the only thing that gives me problems... I do not know my old password Apple ID... I used an email from friends... And I no longer communicate with them and I have no way to get the password... And I would like to delete the old account app ID... So, I can continue to use my other... Please and thank you...

  Remove the apps and download/purchase once again using your ID

• Need to change or remove the user name?

  Hello

  I have created a username of support or forum for the community and was signed to automatically by using the ID of the evil of apple.  Remove the current user name?  If I change it very well, but deletion is also an option if I can create a new one.  None where the Web page asked me for the apple ID.  Just sign me somehow.

  Hello

  I noted your request to the Apple moderators.

  It may be a day or two before they can help. Be patient.

• My Apple Watch asked the password whenever I raise my hand.  He normally only for this, after I removed the watch and put it back on.

  My watch ask me the password whenever I raise my hand to look at. He normally doesn't do that when I removed the watch for charging.  I haven't changed anything so I don't know what causes this problem.  Help, please!

  Hello

  The following steps may help:

  • Make sure detection of wrist is still open:
    • On your iPhone, in the application of the watch, go to: Watch My > General > detection of wrist - turn on.
  • Make sure you wear your watch sufficiently snug on top of your wrist (if it is worn too loosely, your watch may believe that he had been removed from your wrist).
    • Port Apple Watch - Apple Support