Satellite L series reads as a single module of RAM

Similar Questions

• C660 - 10 d should work with the single module of RAM to 8 GB?

  I have a single module of RAM to 8 GB which works very well in Satellite C640, but does not work in my C660 - 10 d.
  Should C660 work with a single 8 GB RAM module, or are you to have 4 GB x 2?
  Any advice much appreciated.
  (The module is Transcend JetRam PC3 10600 (DDR3 1333) 8GB)

  Hello

  The question should be: is the Satellite C660 - 10 d supports 8 GB of RAM?

  According to the information that is on the internet, the C660 - 10 d is supported by the Chipset Mobile Intel (r) GL40 Express.

  This chipset supports only 4 GB of RAM and finally, you can use DDR2 modules 512 MB / 1 GB / 2 GB 667 MHz to extend the RAM

• Satellite A200-1CR does not recognize the module of RAM 2 GB

  Hello

  I have a problem with the extension of the RAM.
  I have the Satellite A200-1CR with 2 x 512 MB of RAM.

  Now, I bought 1 x 2 GB RAM (DDR2 PC2-5300 (667 MHz); PA3513S-1M2G) but the BIOS and Windows recognizes only 1 GB.
  When I add 1x512mo to the second slot, the system recognizes 1.5 GB of RAM.
  Where is the problem?

  What should I do to make it see 2 GB?

  Paula

  Hello

  I think the answer is very simple.
  Satellite A200-1CR can be upgraded up to 2 GB of RAM.
  This means that you can use max 1 GB of RAM in one slot
  You used 2 GB of RAM and this module does not seem to be compatible
  In my opinion if you want to use 2 GB of RAM then you can buy 2 x 1 GB RAM modules

  Welcome them

• Satellite L50 do not identify the second module of RAM

  Hello

  I can't add a Kingston 4 GB ram in my L50 - A - 1 DG computer because the computer does not illuminate after I added a memory module (all other brands like Kingston), I want to know if the computer works only with the original memory module, I should buy an another (the original memory mark) Hynix to add my memory please?

  Thank you very much

  > the computer turns not after I added a memory module

  The laptop can be upgraded to 16 GB because only two memory slots are available.
  32GB are possible only for computers and motherboards with four memory banks

  The laptop does not start because your extra RAM module is defective or not fully compatible. Please also check if the module is properly connected.

  Compatible modules are already mentioned by Timox and you must use the DDR3L 1600 MHz (PC3-12800) SO-DIMM module

• Satellite 1800 Series, upgrade for video editing

  Is it possible use you my Satellite 1800 for video editing. (pinnacle studio 8/9)
  I now 256 MB in use, HD is original and the processor is the processor INTEL celeron-995 MHz.
  And is it possible to replace the DVD on a DVD - RW
  Thank you
  John

  The my Satellite 1800 Series drive is fixed mounted, yours is too (I think). The only way to change the disk is to go to the next dealer Toshiba one ask him if there is a reader, that it might recommend.

• Can I use a module of RAM 2 GB in Satellite M105-S1021

  My TECRA stopped with the BSoD (on another thread) and I had to leave my old Satellite M105 - S1021 and try and get it going again.

  First problem was running PRO XP without service pack and it was a * LEGAL * XP home upgrade - tries to install the SP, I received the product key was not valid message - cannot find the CD of XP Pro I used I called MS Support (sounded like in India) and vain - I expected to be provided with a valid key BUT NO! Why MS play the stupid guys like that on a software product is stupid IMHO and brief overview just puts a bad taste in the mouth and make me want to go to UBUNTU LINUX.

  So I had to search in a room full of hardware and PC (sad hoarder I have still a few BACK/WIN 95/98 machines) until I found a CD of XP PRO with a product key if I had XP PRO installed on this Satellite laptop and installed the latest SP

  BUT then I discovered that this laptop as well as it having previously PRO XP without a service Pack installed, there only 448 MB of RAM installed.

  Looking at the memory Crucial site they recommend an upgrade to 2 GB BUT it's 1 GB x 2. Opening the door of memory I see that I don't have that one not slot the two connectors.
  An upgrade to 2GB created using two modules of 1 GB Mem is therefore not possible.

  So my Question is:
  Can I upgrade to 2 GB using a slot OR slots on this L/T only able to take modules 1 GB Mem - I guess as I can / could get a module DDR2 PC2 - 5300 Mem.

  OR only can I put in a single module of 1 GB Mem.

  Can you please first tell us we are discussing here on laptop Tecra or your old Satellite M105 - S1021?

  For the Satellite M105-S1021 I found follow the news:

  Memory5
  -Configured with 512 MB DDR2 533 MHz SDRAM (using a memory module, a memory xpansion open housing)
  -256MB (min) / 2048MB (max), 512 MB of memory accessible service more accessible by the user memory available slot for 256 MB, 512 MB or 1024 MB DDR2 PC4200 533 MHz SDRAM.

  Compatible memory modules:
  PA3412U - 2M 51 Toshiba 512 MB DDR2-533 memory Kit
  PA3411U-2M1G Toshiba 1 GB memory DDR2 - 533 Kit

• Satellite L40 - cannot read with Windows XP SDHC cards?

  Hello

  last year, I bought a Satellite L40 series and a Windows Vista has been installed on it. I found that everything worked properly.

  Since then, I found that Windows Vista is slower than XP, I upgraded to Windows XP and I installed all the drivers manually. Everything works fine until I found that I can read only SD card with the Ricoh card reader on my laptop. With Windows Vista, he could read SD and SDHC.

  Like all of my files saved to the SDHC, I really want to solve this issue.

  I detected on the computer that is my card reader equipment:

  Ricoh Memory Stick Host controller (1.0.2.5)
  Ricoh MMC Host COntroller (1.0.0.9)
  Ricoh XD-Picture Card Host Controller (1.00.02.08 / 6.0.1.13)

  The questions are:
  1. the drive to read SDHC card with the Windows XP platform?
  2. If Yes, what should I do with it? Maybe I need to install a new driver? (If Yes, where can I find it?)

  Thank you for your concern. I'm really happy if you can help me solve this issue.

  Best regards
  Jenny

  Hello

  You may notice yellow exclamation in Device Manager?

  Normally, the Satellite L40 can read SDHC cards up to 8 GB so my question is have you tried different brands of SDHC cards?
  I have good experiences with Kingston and SanDisk cards.

  In addition, you should check the Web from Toshiba site for an update of the card reader:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Last but not least you have installed all the Service Packs and updates for Windows?

• Satellite A300D - where can I find common modules for XP?

  I got my 300 d satellite with no model no PSAK4E for Windows XP earlier. The only problem is that I can't install the energy saver. The message error «a fatal error has occutred, code 0 x 2» I discovered that this has something to do with the common modules, which I do not think that I have installed.

  However, the problem is that I can't find the common Modules on drivers Toshiba's Web site. Is there another name for the common modules, or are they simply not there?

  I want to reinstall Windows in order to install the common modules first. However, it is a little difficult without this having the installation package. I already tried to do some research on the subject but can't find the right information on my model. I found a few 3rd party software but I don't know if it's a good idea.

  Could someone help me, or indicate where I can find the common modules for my model?

  Hello

  The common Modules are not available for models A300D.
  Person not A300D series needs this module.

  But I found some other Power Saver for Satellite A300D series.
  I chose to ve on the Toshiba European pilot page this:
  -> Satellite A satellite-> Satellite A300D-> all-> Win XP.

  Now, I see two energy saving; 7.04.02.Q and v 7.04.02 v

  Check both

  Before install you it, delete the old version, clean the operating system using the CCleaner, reboot the laptop and try to install once again.

• Satellite L30-113 does not recognize the two modules DIMM RAM

  Hello

  I have a Toshiba laptop Satellite L30 113.
  It has 512 MB of RAM and therefore struggled to run Windows Vista, so I bought another 1 GB of RAM.
  It's DDR2 553 MHZ (PC4200.

  The problem I have is that the laptop does not recognize both DIMMs, i.e. the old 512 MB and the new 1 GB when they are in the whole PC. I tried the two DIMM individually in both slots and there is no problem, but when I install both the system sees just 1 GB. I tried the DIMMs around two ways but without success.

  Did I miss something?
  They should be the same size as in the bad old days?
  What is going on?

  Thank you

  Adam

  > I tried the two DIMM individually in both slots and there is no problem, but when I install both the system sees just 1 GB
  Seems that the two RAM modules are not completely compatible...
  I've read several times on these issues and to be honest it s are not uncommon

  I advise you to buy two identical RAM modules ad then to try again

  I'm afraid there is no other solution for your problem of m.

• I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages for only one comand I need all four messages to display at the same time in VISA SERIES READ BUFFER

  I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages of single command given to this instrument... and I read messages through VISA series READ... during the race, the VI buffer displays the messages individually...  I need all four messages to display at the same time in VISA SERIES READ BUFFER, in order to find more than this block, I should add from the palette of function.

  Disable character of endpoint detection or make four readings where you concantanate simply the strings together.

• Satellite M70 - how to remove the memory module

  Can someone post instructions on how to remove / add modules of memory for Satellite M70?
  Thank you
  FS

  Hello

  It of not difficult to remove or Exchange the memory modules because you only check Chapter 8 and 9 of your owner's manual. In the user manual, you can find a detailed explanation how to do this with a few photos and what you need to the modules of RAM.

  Check this box!

• Satellite L30-149 - does not start with the new RAM modules

  I bought RAM Kingston 2 x 1 GB modules. When I put a single module in my notebook - everything works fine. When I put the two modules - BIOS freezes and cannot start.

  I tried to combine my old module of 512 MB with 1 GB of Kingston, but in this case laptop detects only more great module (Kingston). So, I'm stuck with only 1 GB of RAM. In my notebook BIOS version is 3.10, and it's the last. I tested RAM modules in a laptop and each of them works fine.

  What should I do now? Help, please!

  Download and run www.memtest.org Memtest to test these Modules one by one.

• Is it possible to use the port replicator with the Satellite Pro series?

  Hello
  Is it possible to use the port replicator (Docking Stations) for Tecra series laptop with the Satellite Pro series?

  Hello

  No, as far as I know it of not possible to use a port on laptops Satellite Pro Replicator.
  All laptops that support the Port Replicator has a port extension at the bottom of the unit.
  To my knowledge, the Satellite Pro series don t have this port.
  For now only the Tecra and some units Protégé(ie: S100) supports this feature.

• Re: Satellite U200 - 10K cannot send a single net package using Vista

  Hello.

  I'm sorry for the Crossposting, but I really need your help.

  My Satellite U200 - 10K cannot send a single net package. I have connected the laptop (Windows Vista Home Basic) with the other PC (Windows XP Professional SP2) and gave them the two static IP addresses. Then I ping my PC U200. Everything is Ok, the PC sends out packets and gets answers. After that, I try to do the same to the laptop. And in this case, the U200 cannot send anything on the PC, but can ping itself with its own IP address. All fire walls and anti-virus programms are closed.

  So, at least, I need to know, is this a problem of Windows Vista or of one of the network adapter, should I get the laptop to the service center?

  Thanks for help.

  Alexander.

  The connection to the LAN between Vista and XP computer should Hmm generally works without big problems.
  I wonder what TCP/IP protocol configured?  :|

  Vista uses the IPv4 and IPv6 protocols. I would recommend using the IP v4

  One question; did you install all the Vista patches and fixes? You should do this because of various bugs in Vista

• Satellite A300 - card reader does support SDXC cards?

  How can I find out if my SD card reader supports SDXC cards.
  My laptop is a satellite A300 and the properties of the so-called card reader 'SDA Standard compatible SD Host controller'.

  I am able lto using SDXC cards with this device and if not I am able to upgrade the software to support SDXC cards?

  Thanks for your help

  Hello

  I read in the forum on Satellite A300 card reader and I found the info very useful.
  The card reader supports the types of cards:

  -SD Card - 8MB - 2GB
  -SDHC - 4 GB card
  -photo - 16 MB - 2 GB xD card
  -Memory Stick - 8MB - 256MB
  -Memory Stick Pro - 256 MB - 2 GB
  -MultiMediaCard - 8 MB - 1 GB
  -miniSD (with SD adapter) - 32 MB - 2 GB

  As you can see that the SDXC cards are not taken in charge... in this case I recommend using a common external USB card that would support the SDXC cards