Satellite L300D - using 20 min at startup

Similar Questions

• Satellite L300D-10U - unable to connect to the internet using LAN and Win XP

  Hi all

  I had a very big problem with my card.
  I can t connect to the internet.
  I searched the forum but without any determination :(

  I did everything. I have checked ipconfig nothing, check the mode safe mode with local network nothing.
  Someone said too
  "(1) once the Ethernet is connected, power of the DSL Modem. Cycle." ("Some Modem picks up the MAC ADDRESS of the network card on where it was previously connected and restarting it redétecte this new")

  How to disable the modem?
  And another question: can someone tell me what works of LAN drivers in Sat L300D-10U on XP?
  I put t even know that :(

  Help me

  Hello

  The Satellite L300D-10U belongs to the series of PSLC0E and it supports the Realtek LAN card.
  LAN driver can be found on the page of Realtek.

  You ask how to disable the modem? I think you mean how to reset modem DSL
  Well, usually your modem should support an ON / OFF button simply turn it off and then turn it back on.

  If you are unable to access the internet then you should first check if your modem is properly configured and that the right data ISP (internet service provider) was used.

  Sorry, but that's all I can say right now I think you should just check your modem settings, make sure that the NIC is properly recognized and connect the model of the laptop using a LAN cable.

  All that s

• Satellite A85-s107 - white screen at startup by using the power of the battery

  Satellite A85-s107 white screen at startup by using the power of the battery

  When I boot A85-s107 in battery power, it is get booted up in the background, but my screen is empty.
  After that if I connect it to AC power and switch deactivation/activation of the laptop power button, the screen comes back to life.

  There is no problem when I start upward when it is connected to an electrical outlet.
  Battery is fully charged and computer will work off the battery voltage if I remove AC after boootup

  Any suggestions?

  PS:

  also note that when I remove AC and then reconnect I start the computer on two occasions that it does not start the 1st time?

  Don t need to recharge the battery if the AC adapter is plugged ;)
  Try the tips posted by Alex otherwise it of a hardware problem, in my view, there seems to be something wrong with the motherboard...
  In this case, only the replacement could help and it could be a costly affair

• Satellite L300D - can't watch movies using a Toshiba DVD player

  Hello

  I have a laptop Toshiba Satellite L300D - 12L and the toshiba dvd player has stopped working.

  The laptop is always able to recognize the dvd as the 'AutoPlay' box appears when a DVD is inserted and says ' DVD RW drive (e :)) "at the top of the follow-up to the title of the film.
  I then click on 'play the DVD using a DVD TOSHIBE movie'... and nothing happens.

  I tried several different DVD, which I know work in other laptops or DVD players.
  I tried by following this link...

  http://www.TechSpot.com/VB/topic27616.html

  and deleted the lowerfilters and upperfilters but that cause problems and I had to perform a system restore.
  I'm running out of ideas and I would like to be able to watch DVD on my laptop again because I don't have a TV or a DVD player.

  Any help would be appreciated.

  Thank you.

  Hello

  It seems that the CD-DVD drive can read the disc, but it seems that the Toshiba DVD Player cannot play video files

  Then maybe you should try to play the DVD using other software like Windows Media Player or VLC player download VLC player this small software and install it
  Then try to play the movie

  I recommend also to install the tool called DVD Player Update Check Tool that you find on the European driver Toshiba page.

  With this tool, you can check your laptop, if your DVD player needs an upgrade and if so, it gives you the download link for version upgrade needed.

• Satellite L300D-202: restore using recovery disk does not work

  Good afternoon

  Wonder if anyone can shed some light on this error message I get when trying to restore my laptop...

  «Setting permissions V:\HDDRecovery...»
  V:\HDDRecovery the system cannot find the specified file
  Unpack the WinRE...

  L ' ImageX for Windows tool
  Copyright bla...

  Opening the file in error [V:\HDDRecovery\SWImg\06546XSP.svml
  ERROR: ImageX could not apply WinRE V:\HDDRecovery\SWImg\06546XSP.svm index 1 of the HARD drive to W:!

  Press any key to continue... »

  After that, I find myself with the Toshiba Recovery with no action software and a screen BACK Active but nothing happens...

  I'm guessing that lack of HD, received today from Toshiba for this system recovery media

  Laptop is:
  Satellite L300D 202

  NB. If I restart the laptop start date and shows BOOTMGR is missing Ctrl Alt Del to restart...

  Any help appreciated,
  Thanks in advance,

  Rick0684

  > NB. If I restart the laptop start date and shows BOOTMGR is missing Ctrl Alt Del to restart...

  Hmm... for me, it seems that the laptop does not start from the disc (DVD), but it attempts to boot from the HARD drive...

  In any case, have you tried to boot from another disk; for example, Win XP, Linux Live CD?
  To do this, and check if it is possible... If Yes, format the HARD drive and try to boot from the recovery again disc!

  PS: Have you tried a HARD drive recovery option?
  Turn on the unit, press F8 and choose fix my computer
  After that, select Toshiba HDD recovery option if possible.

• Satellite L300D - how to recover Vista without losing a data partition?

  Satellite L300D - 22K
  Code: PSLC8E-05500CCE
  Vista Windows (Home premium)

  HARD drive has two partitions (visible):
  -C: (Vista)
  -D: (data)

  After installing avast antivirus startup takes 20 minutes (corrupt file?, defective HARD drive?)
  Moved all my personal archives to the D: partition
  Don't know if I can create bootable recovery dvd´s (the system is unstable)

  1 * I´d would like to reinstall vista without format partition D * (where are my data)
  Find this guide for the HARD drive recovery process
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm
  Should what steps I follow?

  2 If the HARD disk is defective, how can I re - install supplied OS (vista) for a new HARD drive?

  can 3 not related to the above, I upgrade to Windows 7 (clean install)
  32 or 64 bit?

  Hello

  I'll try to help you.
  1 > I´d would like to reinstall vista without format the D partition (where are my data)
  > Find this guide for the HARD drive recovery process
  > http://aps2.toshiba-tro.de/kb0/HTD1303440001R01.htm
  > What steps should I follow?
  As far as I know on the second partition of HARD drive folder HDDRecovery is saved recovery image. When you start the installation of (F8 at startup) HARD disk recovery partition recovery image D will be installed on the C partition. In this case the D partition is not deleted. C just partition will be formatted before installation of recovery image begins.
  Just use F8 option and go fix my computer. Just follow the on-screen menu and choose the software factory default recovery option.
  > 2 If the disc is defective, how do I re - install supplied OS (vista) for a new HARD drive?
  After reading this question, I see you didn't read the document s user manuals. You need to create a recovery media (DVD recovery) and this recovery DVD you can use for recovery image installation if there is a problem with the HARD drive or you want to install original recovery image on the new HARD drive.
  3 > unrelated meanings, can I upgrade to Windows 7 (clean install) 32 or 64 bit version?
  Of course you can do it. Please visit the download page of Toshiba on http://www.toshiba.eu/innovation/download_drivers_bios.jsp and check if all the drivers, tools and utilities are available here. Of course before doing this, create recovery DVDs.

  If you have any other questions you are welcome.

• Satellite L300D-12I - No. WLAN and function after reinstalling webcam

  I have the following:

  Toshiba Satellite L300D-12I (model no - PSLC8E-01513EN)
  AMD Athlon X 2-QL-60
  ATI Radeon 3100 graphics card
  Windows Vista Edition Home Premium
  No ser. 68364516Q

  After major problems, I had to restore to the factory settings of the F key at startup. I now can't get the built in wireless and Web Cam system to work!

  Please tell us, in a few simple steps. How to restore these two functions.

  Thank you
  John Gaff

  Hello

  I'm a little confused about your ad m... You wrote that you restore your laptop to factory settings, but now you can t get WLAN and webcam to work?
  Normally, if you restore settings factory using the Toshiba or HDDrecovery recovery disc, all the drivers and tools are installed and everything will work.

  You have yellow exclamation marks in Device Manager?

• LAN extinguish after a few time so that the Satellite L300D-10B is working

  The main problem is that when I try to download something long, after some time (30 min to 1 hour or something close to) the network card is turn off and does not work once again, when I disable/enable it. He started only work when I have my laptop reestart.

  + Computer laptop buyed in January of this year. +
  Model is: * Satellite L300D-10B *.

  I am trying to reinstall the network driver & etc. But it is not useful.
  I think that if immediately on or sleep card network settings, but I turned sleep and @auto disable @ OFF.

  Help to fix this problem.
  Best regards!

  You should try to update the BIOS to check for an update from Toshiba Web site:
  http://EU.computers.Toshiba-Europe.com

  Also, make sure that you have all updates and Service Packs for Windows installed.
  Visit the Windows Update Web site.

  Maybe the problem is also with the firewall or security suite. To update or modify the software.

• Satellite L300D-12u: power supply works not - is threre a guarantee?

  Hello.

  Today, I was surfing the Internet when suddenly my laptop says, is no longer on electricity.
  I touched the power supply and the connector that is immersed in the laptop was very hot (not the big case which becomes usually hot, only the connector).

  I tried several times to make it work again to take a new start or cool connector, but it still does not work.

  To make sure, that it is the question of food, I used the power supply of my mother, who is similar to mine, and then it worked.

  So my question: do I have a warranty on my power supply?
  I bought my laptop to 29.8.2008 in Germany and is a Satellite L300D - 12u.

  Thank you for all the answers!

  Hello

  Adapter is covered by warranty for laptop.
  So if laptops warranty is still valid your adapter should be covered by the warranty as well.

  Visit this link for details of the guarantee:

  http://www.toshiba-tro.de/unitdetails

  Welcome them

• Satellite L300D - corrupted hard drive, no recovery media, no windows key

  I have a Satellite L300D-11V I'm looking for someone who would not go further that a screen blank after windows start logo, and also when you run Startup Repair he would get at this stage even too. Now pressed 0 while starting would not bring to the top of recovery, only an option for Windows Vista.

  With the help of some high end diagnostic software I have diagnosed that the hard drive has several physical defects that could well be the reason for this purpose the reader is better off being replaced. However, because of the mistakes, I am unable to create images of the player via Acronis or similar.

  Buying a new drive no problem, but the person never did no recovery media so it appears I have to buy a Toshiba recovery.

  There is no Windows key on the case anywhere either.

  If I had to buy a Toshiba Recovery, it would be important that I have no Windows key on the presumption that the recovery would be an already activated installation of Vista for laptop?

  Thank you

  > If I buy a Toshiba Recovery, it would be important to have no Windows key on the presumption that the recovery would be an already activated installation of Vista for laptop?
  In this situation best way to solve this is to swap HARD drive, restore disk original order of Toshiba and install Recovery designed for this model laptop image.
  Recovery image should not be enabled. After the installation, it will be activated automatically if you n t need product key of Microsoft for activation.

  Original recovery disk can be ordered on https://backupmedia.toshiba.eu/landing.aspx

  By the way: Win7 32 bit works quite well on this laptop model then perhaps you should install has the version of Win7. Of course if you do this, you need legal product key.
  Anyway it has nothing to do with Microsoft sticker placed on Toshiba laptops. This key cannot be used for activation anyway.

• Re: Satellite L300D comes with the recovery disk?

  Hello

  I don't get a recovery disk when I bought my Satellite L300D.
  Does anyone know if Satellite L300D is provided with the recovery disk?

  As much I know computers made from the middle of 2007 aren't provided with the operating system recovery disks. How can I find out what year my satellite is made?

  Thank you very much

  All new models of laptops including your are delivered without the recovery DVDs.
  Recovery image is saved in the folder called HDDRecovery on the second partition.

  Akuma is right. "You need to create a recovery media using preinstalled" Toshiba Recovery Disc Creator. The shortcut that you can find on the desktop. Please do so and for the creation of recovery media I recommend you to use media high quality as TDK or Verbatim DVD-R.

  You can install OS using the F8 key at startup to the top. The guideline how to proceed you will find under http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm
  Note please. This can be done if this recovery image is not modified or if you install another operating system on the first partition. the second partition can be in original condition, but this F8 option will be gone.

  If you have any other questions please let me know.

• Satellite L300D-13s - how can I restore with corrupted disk 2

  The laptop is a Satellite L300D-13 s.

  I tried to restore the laptop using the restore discs, the first disc has worked well, but he did not recognize the second disk. No matter what I have I could not get to read this disc.

  I then tried the F8 option of us to restore the drive, but I got the missing Bootmgr message. I tried F8 using the DVD, but it doesn't have a restore option.

  Using the option to boot with a record I did access the E drive and discovers the HDDRecovery directory but not found something that would allow me to run a restore.

  Y at - it an option to do a restore in this way, or can I restore another way?

  Your help would be appreciated gratefully.

  Hello

  Recovery procedure can be performed on two tracks:
  -Via recovery CD/DVD or
  -From the HDD recovery procedure

  If there is problem with the created discs, then you should try to use the second option. It works as follows:
  -Start your laptop and press F8 for Advanced Startup Options
  -Here you will see the option to fix my computer
  -Choose this option and follow the on-screen menu.
  -Then, you will encounter the system recovery options
  -The last option is the Toshiba recovery procedure. Select it and follow the on-screen menu.

  Please note: this will work if you didn t change partition structure, installed OS clean or deleted the folder HDDRecovery.

  At the end I have to say, if nothing helps, and if you are not able to install the OS by using one of these methods I see a solution only: you must order the new recovery DVDs.

• Satellite L300D begins only after the battery has been drained and recharged

  I have a satellite L300D that has a problem at startup. Last week, it closed but got stuck on the "Disconnect" screen for a long time. Finally I manually turn it off by holding down the power button. Don't think no more of him it happened sometimes with my computers. However, when I went to turn it back on - it was nothing. Power lights came to the front of the computer, but not to screen at all. Could not even access the BIOS. Nothing. It was like that for several days.

  Tried all the common solutions - removed battery, disconnect the power supply and press the power button - still nothing. Tried w/o - just AC, just the battery. Even stripped down to the motherboard to see if I could remove the CMOS battery and reset the CMOS but it is soldered on the motherboard. Put all back together, still nothing.

  Finally, I had to recharge my cell phone using a USB adapter and given that the computer had power I tried the usb port and it worked (for example, I could charge the phone - still no screen on the computer). The computer's battery is dead and I plugged it in. That evening, after the battery was full, I tried the computer and it has perfectly worked. Started correctly, shut it down, restarted and it was fine. Unplugged this night there and reconnected again in the morning and... nothing. Just a black screen. No BIOS.

  Killed the battery again then reloaded and now my computer is working again.

  Any ideas on what could cause this problem?

  Thanks in advance.

  Hey Buddy,

  In my opinion her only the only one you can is update the BIOS like Akuma suggested. This problem is not related software so that s the only option you have I think. You can download the latest version of the BIOS here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  If this is not the case, contact an authorized service provider please. Guys can fix all this hardware related problems can diagnose this problem. Maybe the motherboard or something else must be exchanged.

  Good luck! :)

• Satellite L300D-13s will slow down the boot process

  Whenever I start the Satellite L300D-13 s computer laptop (using Vista Home Premium with factory settings) I am presented with a Please wait"" message. The startup process can take up to a minute! Is it because of McAfee installing and executing a Bios check, because this does not happen on my desktop PC (Vista Home Premium) except if an update has been installed?

  Apologies for the fundamental question, but this is getting frustrating that this happens every time you start and I don't know why. Please help if you can?

  Thanks in advance...

  Hello

  There are different reasons why your Vista runs slowly.
  The main reason is the enormous amount of processes that are ruining to the background of the OS.

  You should know that the laptop uses different features that are controlled by drivers and tools.

  If you want you could disable some processes using the MSCONFIG. Check the Startup tab.

  Verify that the processes are not really important to you and turn it off.

  Welcome them

• Satellite L300D and display of compatibility of the video driver vga

  whatever that means anyway... compatible vga... He used woork when I download the harware throughr Control Panel and no games that I download do not work on my computer.
  Here are some statistics on my computer...
  ------------------
  Information System
  ------------------
  Time of this report: 14/06/2010, 13:31:16
  Computer name: TOSHIBA-3B322C7
  Operating system: Windows XP Home Edition (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.100216 - 1514)
  Language: English (regional setting: English)
  System manufacturer: TOSHIBA
  System model: Satellite L300D
  BIOS: InsydeH2O Version 1.90
  Processor: AMD Athlon (TM) 64 X 2 Dual - Core TK-57 processor, MMX, 3DNow (2 CPUs), ~1.9GHz
  Memory: 1918MB RAM
  Page file: 256 MB used, 3554 MB of available space
  Windows Dir: C:\WINDOWS
  DirectX version: DirectX 9 .0c (4.09.0000.0904)
  DX setup parameters: not found
  DxDiag Version: 5.03.2600.5512 32 bit Unicode

  ------------
  DxDiag Notes
  ------------
  The DirectX files tab: no problems found.
  Display 1 tab: The system uses the generic video driver. Please install video driver provided by the hardware manufacturer. Features of Direct3D is not available. You should check that the driver is a final version from the hardware manufacturer.
  Sound tab 1: No problems found.
  Music tab: no problems found.
  Input tab: no problems found.
  The network tab: no problems found.

  --------------------
  DirectX Debug levels
  --------------------
  Direct3D: 0/4 (n/a)
  DirectDraw: 0/4 (detail)
  DirectInput: 0/5 (n/a)
  DirectMusic: 0/5 (n/a)
  DirectPlay: 0/9 (detail)
  DirectSound: 0/5 (retail)
  DirectShow: 0/6 (detail)

  ---------------
  Display devices
  ---------------
  Name of the map:
  Manufacturer:
  Chip type:
  DAC type:
  Device key: Enum\
  Memory display: n/a
  Current mode: 1024 x 768 (32 bit) (1 Hz)
  Monitor:
  Monitor Max RES:
  Driver name: vga.dll
  Driver version: 5.01.2600.0000 (English)
  DDI version: unknown
  Driver attributes: Final retail
  Format/driver Date: 04/08/2004 08:00, 9344 bytes
  Would be WHQL logo: Yes
  WHQL Date stamp: n/a
  VDD: n/a
  Mini VDD: vga.sys
  Mini VDD Date: 2008-04-13 14:44:40, 20 992 bytes
  The instrument identifier: {D7B70EE0-4340-11CF-B063-282AAEC2C835}
  Vendor ID: 0x0000
  Device ID: 0x0000
  SubSys ID: 0x00000000
  Revision ID: 0x0000
  Revision ID: 0x0000
  Video Accel:
  Deinterlace caps: n/a
  Registry: OK
  DDraw status: not available
  D3D status: Not available
  AGP status: Not available
  DDraw Test result: does not work
  D3D7 Test result: does not work

  Hey girl

  What is your real problem with your laptop satellite?
  Installation of the display may be driver?