Sir my network smart vaio does NOT start after installing windows 7 ultimate 64 bit

Similar Questions

• WiFi not detected after installing Windows 7 Ultimate 64 - bit Elitebook 8740w

  Hello

  I used a DVD to install Windows 7 Ultimate 64 - bit to replace Windows 7 Professional 64 - bit on my Elitebook 8740w. In the end, I used a new facility as the upgrade option ended with a failure error. However, after the clean installation, it cannot detect any wifi. What drivers I am likely to need download and re - install?

  Thank you, in advance.

  Kenwin

  Hi, Kenwin:

  Here is the link to the wireless card driver you need:

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=4137878&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_108502_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• His Dell Inspiron 1420, microphone and camera integrated into the laptop does not work after installing Windows 7 Professional

  No sound from my Dell Inspiron 1420 and the microphone and built-in laptop camera do not work after installing Windows 7 Professional 64-bit. My laptop has Windows 7 Vista 32 - bit family premium. My laptop is 64-bit capable and after going through the Upgrade Advisor, I installed Windows 7 64-bit. I can hear sounds when I use a headset plugged into the line-in Jack, but not through the speakers built into the laptop. I already tried new drivers from the Dell website, but I could not find.

  Any help will be much appreciated. Thank you.

  As it is has no drivers 64 bit Windows 7 on Dell Web site, your best chance is to install the 64-bit versions of Vista (if they exist) in compatibility mode, viz:

  Right click on the Vista driver, then select Properties > Compatibility tab. Now choose to run the program in Vista compatibility mode and then apply > OK. Right click on the file and select run as administrator to install it.

• Windows Vista does not start after installing Linux OS

  original title: Windows Vista does not start after the installation of the Linux OS... Help!

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  Hey Oscar Jose

  Download the correct ISO file and make a disk bootable from the link below

  Then use the Startup Repair option when you start from

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  or at startup press F11 to start the process of restoration of hp and see if you can reinstall vista from the recovery partition and place your machine, back to the way you bought

  warning you all data loss and 3 third-party programs that you have installed unless there is a non-destructive option in your hp recovery options

  Thirdly try to ask in a fedora forum to solve the problem, he has caused

  http://fedoraproject.org/

  Walter, the time zone traveller

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• computer does not start after installing video card

  I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

  Gary,

  You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

  When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

  Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

• Computer does not start after installing a new graphics card

  I am owner of a HP Pavilion H8-1020 with a processor intel i7 - 2600 s Windows 7 and am trying to upgrade my Radeon hd 6570 to a Gigabyte AMD Radeon R9 280 OC. I improved my diet for a Corsair CX750 to meet the requirements of power and installed with number. After the installation of the new card, which as far as I can tell is well seated in the pci slot and correctly connected to the PSU, my computer does not start.

  System powers on, all fans of begin to run including the fans on the new graphics card, but it does not begin the boot process, no entry is received at my monitors, no light on the keyboard, my OS starts loading, I can turn off the system without the delay that will flow normally. Then I reinstalled my old graphics card and the computer started as usual.

  Now, assuming that the card is not DOA, which unfourtunatly I have no way to verify, and I'd like to see if it could be another problem before going through the process of restitution. I did some reading on the internet, which helped, but did not help for a technological neophyte like me.  Now, I know a few things that could cause this problem but lack the necessary skills to determine what question is making me. What I've read, these could be possible questions:

  1: my new graphics card is not compatible with my motherboard. It's something I know now that I should have checked before buying and something I should theoretically be able to do it now, but I am at a loss on how to do it. My card is compatible with my motherboard?

  2 could be a BIOS problem. I updated my bios driver with the version provided by the HP site. I am running FRIEND 7.16 05/10/2011.  And from what I've read it might have something to do with my bios to UEFI mode and I would need to go to a legacy mode so he can recognize a new device, is it true? I am extremely wary of messing with my BIOS settings for fear of bricking my system. How can I check my current BIOS settings are and what I should change and how would approach I change them? Will one of these changes affect my system if they are not what is not causing the problem?

  In addition to these issues, anyone know any other matter which may be the cause of the problem that I should look for? Thanks for any help.

  Hello @Eric_Z,

  I can see why you are having problems with your new graphics card, and to get to the fast response that your motherboard is not compatible with the new graphics card that you have purchased. And here's why.

  Your motherboard according to the page HP Pavilion HPE h8-1020 Desktop PC product specifications is the Carmel motherboard, which has the following expansion slots:

  • A PCI Express x 16
  • Three PCI Express x 1 connectors
  • A PCI Express Mini Card x 1

  As there is no version indicated for your PCI Express x 16 it slot means that it is version 1.

  Now, your previous graphics card was a PCI Express 2.1 x 16, which means that it was version 2 and compatible with your PCI Express x 16 slot on your motherboard. However, the new card is PCI Express 3.0 and will not work in your motherboard due to a compatibility break. While the technology is supposed to be compatible there are many cases where it is not, and I'm afraid that you meet one of these cases.

  I am offering an overclock.net article entitled: the final answer to the controversial compatibility of PCIe x 16 version. where your situation has been tested and examined.

  I hope this helps. Have a great day and thank you for display on the HP Forums!

• Laptop does not start after installing vista sp2

  My Dell XPS 1530 stopped working after installing vista sp2. He gave me instructions for installation, step 1 of 3 and it went all that they way up to step 3 of 3 and said its closure and never came back...
  Please let me know, how to start the laptop.

  Hello GoogleGuru,
  Thank you for visiting the Microsoft Answers forum.
  Because your computer does not start until the desktop computer, we were able to try the system restore to a point before you install SP2.
  Thus, with the computer is shut down. Press the power button, then press on and press F8 until you see the startup options, and then it will give you the ability to boot to the last known good configuration. (select it).

  If this does not work, you can try to boot from the Vista DVD and use the recovery console to perform a restore of the system to another point in time.

  Post back with the results.

  Thank you

  Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Creative Cloud Desktop App does not start after installing Mac OS Yosemite

  Hi all,

  I just updated my Mac OS to Yosemite. Now, Creative Cloud Desktop App does not launch and InDesign CC 2014 (10.1.0.71) crashes trying to find the Roman.txt file, I have replaced it with a copy of the TimeMachine when he worked in the Mavericks.

  I trashed the caches and reinstalled the same preferences, but it keeps on does not start.

  The rest of the applications (with the exception of InDesign and Creative Cloud Desktop app) do not work properly.

  All ideas will be welcome.

  Thank you!

  Mac migration (or Time Machine) do not work with the Cloud program activations

  Uninstall... to run vacuuming... Restart your computer... Reinstall

  -using the vacuuming after uninstalling and before you reinstall may help

  -http://helpx.adobe.com/creative-cloud/help/install-apps.html (and uninstall)

  -http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

• HP Solution Center does not work after installing Windows 10.

  After 10 Windows Installer, Solution Center HP, which is part of the installation of software for my HP Officejet 4500 510nz, tells me that the software is incomplete. The installation disc does not open, so I downloaded the HP program and re-installed. I always get the message that the software is incomplete. HP says they no longer support this printer (bought 24/05/14 - May 25/09/13!) - WOW! ~ printer still print, but will not run the other functions such as scanning, etc., because the HP Solution Center does not start, and HP has abandoned in favor of their product.

  Now what? Should I buy a new printer to replace this year 1 old HP so I can use its features with W10?

  Or, is there a way to fix it?

  This thread has been locked, for more information on HPPIW, please refer to the following support document:

  http://support.HP.com/us-en/document/c02681060

  HP printer Installation Wizard is an application of HP support that helped to download printer software. This support request is no longer supported by HP. This software was last updated was September 22, 2015.

  To download and install the latest version of the software for your HP printer, please visit 123.hp.comor HP support Web site, HP Support Assistant (in English).

• Does not fingerprint after installing Windows 7

  I bought 3 items of T500 with installed Windows 7 Home. With this OS footprint scaner worked properly.

  After installing Windows 7 Professinal, fingerprint reader does not work. All instaled divers. There is no error in DeviceManager. But when I run the software of fingerprints, it is said that scanner is not lit.

  Make sure that the installed driver is actually the one that came with the Lenovo Fingerprint Software and not the one that you got from Windows Update. I've seen similar problems several times where Windows 7 is installed and get fingerprints from windows update driver/software and the software Lenovo to fingerprints do not work because some parts of the software, I got from windowsupdate is left on the computer.

  Which version of the driver of the fingerprint reading is installed on your computer?

  You can try uninstalling Lenovo Fingerprint Software and restart. Then, after the reboot if there is still a driver installed for the fingerprint reader in Device Manager, right click and select uninstall and also check the box that says to delete the driver. You may have to restart again. If you had several drivers fingerprint installed you may need to repeat this step twice. So when Device Manager shows the fingerprint with no check reader driver installed if you have any software fingerprint authentec or authentec truesuite installed under "uninstall or change a program". If you find any uninstall and restart. If you can successfully eliminate all the reader of fingerprints in the device should be listed in Control Panel with no driver installed, you should find any substance of fingerprints or biometrics. Then try to install the Lenovo Fingerprint Software.

  -gan

• Satellite P300-1This - Microphone does not work after installing Windows 7

  Hello world.

  At first, I'm sorry for my bad English, so I will say in no time.

  A few days ago, I removed a few programs, and I installed the new Windows 7 operating system. Everywhere I had to download the new drivers for the camera because they do not work. After you download the drivers of the camera, the camera become operative (YES!), but later worked for me, a built-in microphone was out of use. What may be of it with the cause and this driver to download and why the microphone not working?

  I can't talk with friends on Skype ;( Help me. I hope you know what I'm saying.

  Hello

  Do you really install any drivers after installing Windows 7? Maybe you have forgotten something and so it doesn t work.
  Micro is a part of webcam so be sure that driver webcam is properly installed and driver sound, you need to as well.

  After that, check the sound settings. Make sure that the Microphone is enabled and test it again with amp active microphone.

• Windows does not start after installing sp3

  I had windows xp with sp2 and sp3, I downloaded. Once the download is complete it asked me to restart the computer. Windows will not go up. No error message, but it will work when the system is in safe mode. In addition, windows update does not load. Any ideas?

  You are a candidate for this patch before installing SP3...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=UK&LC=en&DLC=en&softwareitem=PV-60484-2

  .. you are if your PC is a HP Pavilion and Presario, Media Center and has an AMD processor

  To find out if you have an AMD processor...

  • Hold down the Windows (between Ctrl and Alt) key and press Pause break
  • Your processor type is shown in the computer: section (see below)

  You can do a restore of the system in safe mode to get rid of the SP3...

  http://support.Microsoft.com/kb/306084/en-GB

  Tricky

• Siebel Server does not start after installing Siebel 8.2.2 (Linux): SBL-CSC-00025

  Hello

  I installed siebel on Oracle linux 6.1 8.2.2 x86_64, Oracle HTTP Server 11 and customer DB Oracle. I have an existing database on another linux machine.

  I have the connection with my database by odbcsql in the siebsrvr folder. Gateway is started correctly. When I run the Siebel server (. / start_server) it works very well for a few seconds and then dies with the following newspapers:

  SiebSrvr.log:

  
  

  1021 2015-03-08 15:42:49 2015-03-08 15:42:50 + 0100 000000a 9 001 09 0001 SiebSrvr 17947 1439700720 /u01/app/oracle/siebel/8.2.2.0.0/ses/siebsrvr/log/SiebSrvr.log 8.2.2 ffff [22314] ENU

  GenericError 1 00005a3354fc40f1:0 GenericLog 2015-03-08 15:42:49 (sccnmsys.cpp (1306) err = 2883609 sys = 0) SBL-CSC-00025: no value found in the bridge. The default value of the repository is used.

  GenericError 1 00005a3a54fc40f1:0 GenericLog 2015-03-08 15:42:49 (sccnmsys.cpp (1306) err = 2883609 sys = 0) SBL-CSC-00025: no value found in the bridge. The default value of the repository is used.

  GenericError 1 00005a3b54fc40f1:0 GenericLog 2015-03-08 15:42:49 (sccnmsys.cpp (1306) err = 2883609 sys = 0) SBL-CSC-00025: no value found in the bridge. The default value of the repository is used.

  .....

  .....

  GenericError 1 000053f954fd0cb4:0 GenericLog 2015-03-09 16:44:52 (sccnmsys.cpp (1287) err = 2883602 sys = 0) SBL-CSC-00018: internal: the value of demand has never defined by the repository of DRS or the backup store.

  ....

  ....

  GenericError 1 0000550354fd0cb4:0 GenericLog 2015-03-09 16:44:52 (sccitems.cpp (310) err = 2555932 sys = 0) SBL-SCM-00028: key not found 1 GenericError GenericLog 0000550354fd0cb4:0 2015-03-09 16:44:52 (sccconfg.cpp (2149) err = 2555932 sys = 0) SBL-SCM-00028: key not found

  ---------------------------------------

  And SrvrMgr.log:

  SBL-SVR-03005: no server connection string for Siebel component Siebel Enterprise (null) (null), (null) Siebel server

  -----------

  (When setting up Siebel server I had bit the same mistakes but configuration completed successfully.

  SBL-Gen-05004: Key is not found.)

  ----------

  I did the installation steps very carefully. Source: SiebInstUnix.pdf (roadmap for installation) and the configuration of the Siebel business with an existing database Applications

  Help, please

  That's ok. I found error messages that are similar to article ID 1151183.1. Check if the Siebel server starts after a reconfiguration of the siebel server.

  You can also attach your siebns.dat to review file if you wish. It should be available under the u01/app/oracle/siebel/8.2.2.0.0/ses/gtwysrvr/sys directory.

  Thank you

  WSiebel