Sound does not work after you install the update of the IDT High Definition CODEC on DV6 series laptop driver

Hi, I have edition entertainment laptop HP Pavilion dv6 Windows 7 64 bit OS. I'm used to unsuccessfully drivers every month and everything is fine, but 3 days ago I downloaded the new IDT High Definition Audio CODEC drivers. After installing his system stops working. I tried several times to back the drivers and install them again, but in both his case has not appeared. What should I do?


Uninstall the driver, and then install the codec Microsoft UAA before reinstalling the previous audio driver.

Please post your results here in your thread.

Best regards


Tags: Notebooks

Similar Questions

  • print DigitalPersona finger scanning does not work after you install the recommended updates

    My impression of digitalpersona finger scanning does not work after you install the updates recommended on my dell Vista


    1. do you have an error message?
    2. are you referring to the print scan hardware or software scan print that was supplied with the device?

    Method 1:
    I suggest you to update the software DigitalPersona from the link below

  • Internet Explorer does not work after you install the kb2761451 update

    Original title: I downloaded the update and now Internet security security update kb2761451 explore does not open.  So I deleted it and Explorer opens.  This update is listed as important.  What should I do?

    The Explorer is 9.


    Thanks for posting the question in the Microsoft Community!

    Internet Explorer stops working after the update kb2761451 is installed.

    The problem may occur if the updated components are corrupted.

    I suggest you follow the steps mentioned below:

    Method 1: Of reset Windows Update components


    See the site:

    How to reset the Windows Update components?

    Warning: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    Method 2: run the Update of the system analysis tool

    See the site:

    System update scan tool corrects errors of Windows Update in Windows 8, Windows 7, Windows Vista, Windows Server 2008 R2 and Windows Server 2008

    I hope this helps. If the problem persists, let know us and we would be happy to help you.

  • Re: Portege R500: controller button does not work after you install the update

    After you have installed the latest version of Toshiba Value added Package, the two buttons (toshiba assist, and backlight power) do not work properly: they open instead a window of Firefox.

    I guess there is something to configure in the section "Optimizing" Toshiba Assist.
    When I open the program "Toshiba buttons functions" (sorry for the puny, Spanish translation, it is called: "functions of Toshiba botones") all entries are empty and I have to enter the Url of the program supposed to turn off the backlight of the screen of my LCD...
    I have no idea where to find this executable.

    Can someone help me?

    Why you n t use the OS restore option?
    The operating system supports the option of system restore and this helps to put the system in the previous point.

    Check, maybe it helps to get the old version of the Toshiba Package Value added.

  • USB does not work after you install the utility on Satellite A200 Intel chipsets

    I installed Win XP Pro SP2 on my Satellite A200-1SM and everything was ok until I installed Intel Chipset Software Installation Utility version (recent ones on the site of download of Toshiba; before this step all USB dev. worked properly), after all my USB devices wouldn't work. I had my windows up-to-date with updates from Microsoft, but that has not changed a thing.

    I use Vista once again, but still want to work one day at the XP operating system.

    Please help me if you can.

    Like the previous user said, the chipset must be installed as first pilot
    In addition, it seems that this laptop supports the Intel® GM965 + ICH8M Intel chip.
    It would be advisable to check the version of the Intel page directly

    Hey Buddy

  • Outlook 2003 does not work after you install the update Outlook 2007 (KB2412171) _

    I run Windows 7 and Outlook 2003 but the update automatic KB2412171 causes Outlook to crash into the opening with the message "Microsoft Outlook has stopped working" and the program must close so I'm not able to use Outlook at all.

    Please can someone help me with this.

    In these forums, you will find some support for Outlook (2003): ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Why the highlighting of text in a PDF document does not work after you save the file

    Why the highlighting of text in a PDF document does not work after you save the file

    What application you use to highlight?

  • HDMI port does not work after you refresh the computer.

    Updated my computer and now my HDMI port does not work. I can not connect my labtop to TV.

    Are you sure that the additional monitor is turned on.  Try holding down the and then press P until it is selected to extend the screens.

    If this does not work, go to your computer manufacturer's website and download and install the latest version of your graphics drivers.

  • Laptop does not work after you remove the virus win32/winfixer

    Original title: win32/winfixer

    I had cleaned up my n cell phone it's a bad virus win32/winfixer and now my laptop does not work because I deleted it and also my big computer will not work right there problem downloading it says it needs to microsoft.net1.1sp1 ep, but it does not load become crazy pls help me...


    1. what exactly happens when you start on the desktop?

    2. you get any error message?

    3. is your laptop work fine in safe mode?

    4. What are you trying to download?

    5. How are you trying to download?

    6. What is the full error message do you get?

    7. don't you make changes to the computer until the problem occurred?

    I suggest you to see link below and check if it helps.

    Method 1: How to fix a computer that does not start.

    More information: Advanced Troubleshooting for General startup problems in Windows XP:

    Hope this information is useful.

  • sound does not work after you reinstall

    Original title: I had to reinstall xp on my computer after doing so, I can not speaker working

    can anyone help, I can't get my speaker to work after reinstalling Windows xp, because they don't have any softwear with them

    Perhaps, you resorted to reinstall windows because your computer has become unstable because of a faulty hardware, such as a system driver or faulty hardware under sound.

    in all cases, you should try to re - install all software and hardware drivers on your computer directly from its place of origin.

    In addition, it is unclear if you do or you don't have a card its pci added to your motherboard at the moment.   But if you do, then you will need to re - install the software and drivers of its place of origin.

  • Problem with the HP Media Center M7670. UK - a - does not start after you install an update to Apple Quicktime

    I just installed the latest update to Apple Quicktime (once an update message appears on the screen). When asked if I wanted to re - start the PC now, I clicked on Yes.

    Now the computer does not start. The power led lights up, then the hard drive light blinks for a while, then nothing happens and the PC begins to beep. The beeps are repeated, with 2 short beeps and one long beep. What do the beeps mean?

    Then a CMOS clear would be the next logical step in troubleshooting.

    Here is a link to your motherboard page.

    Clearing CMOS information at the bottom of the document.

    It is usually the last step before giving up on a motherboard.

    The problem you are experiencing is hardware motherboard related firmware.

  • Camera does not work after you reduce the screen brightness


    I have an application that uses the camera in QML. It works fine, but if the screen fades while my application is open the camera no longer until I restart the application.

    Here is the page of qml any camera:

    import bb.cascades 1.0
    import bb.cascades.multimedia 1.0
     * Most of this code was copied from:
    Page {
        property string pictureLocation: ""
        function closeCamera() {
            pictureLocation = "";
            saveID.enabled = false;
        titleBar: TitleBar {
            acceptAction: ActionItem {
                title: qsTr("Save")
                id: saveID
                enabled: false
                //title: "Save"
                onTriggered: {
            // The 'Cancel' action
            dismissAction: ActionItem {
                title: "Cancel"
                onTriggered: {
                    pictureLocation = "";
        onCreationCompleted: {
            // Check to see if any cameras are currently accessible.
            if (camera.allCamerasAccessible) {
                // Open the rear camera.
                camera.isOpen = true
        Container {
            layout: DockLayout {
            // The Camera object.
            Camera {
                id: camera
                preferredWidth: 768
                preferredHeight: 1280
                objectName: "camera"
                property bool photoBeingTaken
                property bool isOpen: false
                onTouch: {
                    if (event.isDown()) {
                        if (photoBeingTaken == false) {
                            // Take a photo, and automatically
                            // save it to the file system.
                // The following are examples of slots that can
                // be used with the Camera object to handle
                // the various signals that are emitted.
                onCameraOpened: {
                    // Once the camera is open, start the viewfinder.
                onCameraOpenFailed: {
                    console.debug("Camera cannot open");
                onViewfinderStarted: {
                    console.debug("Viewfinder has been started");
                    photoBeingTaken = false;
                onViewfinderStartFailed: {
                    console.debug("Viewfinder could not be started");
                onPhotoCaptureFailed: {
                    console.debug("Photo could not be taken");
                    photoBeingTaken = false;
                onPhotoSaveFailed: {
                    console.debug("Photo could not be saved");
                    photoBeingTaken = false;
                onPhotoSaved: {
                    saveID.enabled = true;
                    photoBeingTaken = true;
                    console.debug("Photo has been successfully saved");
                    photoBeingTaken = false;
                    pictureLocation = fileName;
                    var imageName = pictureLocation.substring(pictureLocation.lastIndexOf("/") + 1);
                    var imagePath = "/accounts/1000/shared/camera/" + imageName;
                    cameraPreview.imageSource = app.getCameraPreview(imageName, imagePath);
            Container {
                layout: StackLayout {
                leftPadding: 10.0
                topPadding: 10.0
                Container {
                    preferredHeight: 200
                    preferredWidth: 200
                    horizontalAlignment: HorizontalAlignment.Left
                    Container {
                        verticalAlignment: VerticalAlignment.Center
                        ImageView {
                            id: cameraPreview
                            verticalAlignment: VerticalAlignment.Fill
                            horizontalAlignment: HorizontalAlignment.Fill
                            scalingMethod: ScalingMethod.Fill

    Thank you


    so, there is a signal of cameraResourceReleased which you can listen to that will tell you that the camera has been arrested.

    After that, you can restart the viewfinder after your application is in the foreground.

    We have a corner case that we are still working on what centers around the case when the screen starts to close (causing the camera to stop), but the user he wakes up before the browser tells your application in the background.  In this case, you may not receive a leading event.  You can probably work around this case by launching a timer and check, after a second or two, if the application has been deleted original or not... If it is still in the foreground, then you could try restart the viewfinder

    See you soon,.


  • Windows does not restart after you install the new hard drive.

    Hi, I upgraded from 100 gig 250 gig drive hard nice clean installation, worked perfect. Turn off the laptop, turn back on and only bios are accessible, without window, just a black screen with a small white bar flashing at the top of the screen. Put old drive in, everything works fine and in disk management the new shows drive but are not accessible? Anyone got a clue?

    Now I found the answer to my problem. Acer Aspire9802 WKMI recovery allows only 32 GB max loading mbr, therefore partitioned readers with a free partitioner and ye he

    The free program, I called EASUS PARTITION MASTER, dead easy to use for a novice like me! and with an instruction book complete in pdf format

    every 4 years, 21 '' screen singin' and laptop dance - now considered to be old!

    I guess if the sata drive is the same sata version as controller on your laptop, that's to say sata 1 or 2 or 3
    And if a later version of the sata it's backward compatible?

    Use the utility disk provided by the manufacturer of the drive check

  • My phone is lock and does not start after you install an update to Windows.

    After you have installed the Windows Vista Home Premium on my laptop, I am unable to start my laptop properly.

    Boots systems and load normally until the display of connection where instead of the login screen, I show the screen updated frozen on "Installing part 3/3 (0%) update." The laptop stays on this screen, with the cursor froze with a loading icon, for about half a minute until the screen shuts off and reboots the system, put the system in a loop, I can't on.

    I tried: turning off on and powered. using advanced boot options to open the system to all types of 'Safe Mode' and leaving the laptop for some time before trying to turn on the system again. All these things have not worked and the system remains in the lock down.

    I wonder if it is a common problem after the latest Vista updates or if it is more specific to my laptop. Whatever it is, any kind of feedback and advice would be most appreciated.

    Thank you.

    After you have installed the Windows Vista Home Premium on my laptop, I am unable to start my laptop properly.

    "part 3/3 (0%) update installation." ... and restart the system.

    See if this sugesstion can help you:- >

  • Windows Media Player 12 does not work after you choose the initial settings

    I tried to use windows media player 12 on my computer laptop windows 7 and it won't work. It worked the first time and I chose my settings, but it would not open the player itself. I tried to do it on the guest account, but it's the same thing. Does anyone know how to fix this? -Chris

    My post was actually in response to JRTLOVER:

    Why we cannot uninstall and reinstall from the CD just Media Player... or is there a way to fix this?

    I have seen that it was already proposed earlier in this topic, my apologies.

    Regarding your problem, have you tried to launch directly executable WMP? To do this, click Start, type wmplayer.exe in the search box and press ENTER.

    You should also check if WMP is already running: start the task (Ctrl + Alt + Delete) Manager, look for one or more elements called wmplayer.exe on the process tab, select each item and then click end process , then try to start WMP again.

    Tim Baets

Maybe you are looking for

  • IPhoto and iCloud library backup

    Hello - I've changed the location of the iPhoto library of HD on an external drive.  iCloud as results started to download all the photos again.  ICloud creates a duplicate? How can I make iCloud realize that this is the same library?

  • Satelite C875-1FZ - keys on a keyboard failure

    Hello When I start my Toshiba Satellite C875 1FZ some keys do not work. Usually what I do I open Notepad and press the keys not functional and after awhile, they slowly begin to work again.I need to continue to use the keys then otherwise these keys

  • Re: Satellite Pro A120: cannot select an option on the recovery disk

    Hello I have a Toshiba Satellite Pro A120, which has recently been faced with the "alert: System protection failure! "password:" problem that it turned up on some BIOS password unknown on its own in the middle of normal operation. I got that fixed lo

  • Questions about various issues on a Satellite A30

    OK, for starters, I don't know much about computers without talking about laptops, but my husband is "generally" with them, but now that we have major problems. I have a Satellite A30 (not sure if he's a pro, because it does not mention it in the man

  • I have a printer hp officejet j4680 and windows 7. I can't use the cd to install for analysis.

    I have Windows 7 and I have a HP Officejet j4680, I couldn't use the instillation Cd to install the printer, but my computer has found the driver. The problem is that I have to analyze something and scan Windows fax program cannot find the scanner. H