Strange error with cRIO and scan Mode

Similar Questions

• limitations with cRIO in Scan Mode

  Hello!

  I use a cRIO to get five channels of analog voltage in Scan Mode. I have three parallel Timed-while loops. When I use a 1ms dt, the vi does not run and cRIO is disconnected from the project (it is said that cRIO does not). When I use a 100ms dt vi works normally. But the acquisitions must be made with an interval of 1ms. The possibility exists to be a limitation of the Scan Mode?

  Thank you!

  The analytical engine should be able to manage the acquisitions 1ms, but make sure that you configure the engine to scan for 1ms period.  You can synchronize call analysis engine loops instead (it's one of the timed loop timing options).

  If you try to run 1ms loops and there are a lot of things in the loops, you may lose the connection with the cRIO because the thread that serves the TCP connections runs at a lower priority than call loops.  If the call loops all the time take processor, there is no time CPU to manage communication.  Do you need to process each sample as you receive it, or you can read data from each ms but more slowly process it in batches?  If you download your code, we can help you eliminate inefficient code that slows down your curls.

• read the temperature of the chassis of a cRIO in Scan Mode?

  I am trying to create a section for monitoring my VI which monitors the status of the cRIO 9022 and backplane (9104) I use. I understood how monitor memory, CPU utilization, and the input power voltage.

  I know that you can monitor the temperature of the chassis using the FPGA options, but I want to keep my cRIO in Scan mode. Is it possible to access the scan mode chassis temperature probe?

  I found the solution I was looking for. NOR has built a VI to get the temperature of the cRIO, but it's not easy to find or in the open air.

  It is located here:

  c:\Program Files\LabVIEW 8.6\examples\CompactRIO\Controller Specific\9022 voltage and temperature Monitor\cRIO-902 x Support files

  "The cRIO-902 x Support Files" is a library that contains 2 VI is used for the sub - VI voltage monitor, and a third VI called "get Council Temperature.vi.

  Drop in the cRIO app and the Vi shows the temperature of the CPU cRIO in ° C card.

• Strange error with RHCL RH10 and RH11 command-line compilation

  Hello once again, RoboHelp gurus!

  I feel a strange error using the compilation process command-line rchl in RoboHelp 10 and 11 of RoboHelp.

  Here is the command I use:

  CD "C:\Program Files (x 86) \Adobe\Adobe RoboHelp 10\RoboHTML.

  RhCl "C:\folder\project.xpj"-l "SSL_Name" o "c:\outputfolder" g "C:\log\folder\logfile.txt".

  When I generate the log of the cmd file, I see an error "LILo: BIBCientInit could not initialize" twice in the window of cmd prompt while compiling is the treatment.  The cmd prompt window looks like this:

  
  

  C:\Program Files (x 86) \Adobe\Adobe RoboHelp 10\RoboHTML > RhCl "C:\projectfolder\project.xpj"-l "SSL_Name" o "c:\outputfolder" g "C:\logfolder\logfile.txt" [press ENTER]
  

  LILo: Could not initialize BIBCientInit
  

  LILo: Could not initialize BIBCientInit

  C:\Program Files (x 86) \Adobe\Adobe RoboHelp 10\RoboHTML >

  
  

  The created FichierJournal.txt has no mention of ""LILo: BIBCientInit could not initialize "it contains."  Compiling builds without problem, as far as I can tell.

  
  

  The same thing happens when I do not create the log during the cmd file and it errors record right "compensation output folder.  But, it seems to me that the output folder does not actually get disabled.

  
  

  This allows the viewing of the compilation process line by line in the cmd prompt window.  When the compiler indicates "output Compensation folder...". ', the ' LILo: BIBCientInit failed to initialize "error message appears twice, and then the process continues.

  Here's the command:

  CD "C:\Program Files (x 86) \Adobe\Adobe RoboHelp 10\RoboHTML.

  RhCl 'C:\folder\project.xpj'-l 'SSL_Name' o 'c:\outputfolder '.

  The cmd prompt window looks like this:

  
  

  C:\Program Files (x 86) \Adobe\Adobe RoboHelp 10\RoboHTML > RhCl 'C:\projectfolder\project.xpj'-l 'SSL_Name' o 'c:\outputfolder"[press ENTER]

  Adobe (R) RoboHelp version 10.0.0.287 Project command line compiler

  Copyright (C) 2006-2007 Adobe Systems Incorporated and its licensors. All rights reserved.

  Project: C:\folder\project.xpj

  Page layout: SSL_Name.

  Output: c:\outputfolder.

  Scanning for the compilation project...

  Review completed.

  ATTENTION: No luggage description of the file.

  From compilation...

  HTMLHELP 10.0.0.287 preprocessor

  Compilation C:\folder\! chm_tmp_folder_0\project.xpj ...

  Preparation create HTMLHELP...

  Compensation output folder...

  LILo: Could not initialize BIBCientInit
  

  LILo: Could not initialize BIBCientInit

  Preparation of the HTML Help files...

  Copying files...

  ...

  It's okay if it's a HTMLHelp or WebHelp output.  Any thoughts on what is this error and what is the cause?

  I've been away from RoboHelp for about 9 months, but I'll be back on the same projects and the same version of RoboHelp 10 and the same compilation process.  The difference is that I have a new laptop.

  Thank you very much in advance for your time!

  EA

  Adobe was able to recreate this issue on their end, and a bug was created for her.

• Error with Facebook and other web pages; document. Body' is null or not an object

  Original title: error line: 19 tank: 23004 error line: 20 cha:124

  document. Body' is null or not an object line: 19 tank: 23004... object doesn't support this property or method line: 20 char: 124... I get these errors on facebook and other web pages help me please!

  Hello

  IE - Tools - Internet Options - Advanced tab - navigation on the article - check the BOTH Disable script
  boxes of debugging.

  Close and restart IE.

  ------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ========================
  ========================

  Tips for solving problems with Internet Explorer
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-solving-problems-with-Internet-Explorer

  ------------------------------------------

  Methods more troubleshooting for Facebook and other questions of the site, if needed:

  Try to add to your trusted sites in IE - Tools - Internet Options - Security - Trusted Sites.

  https://www.Facebook.com/

  http://www.Facebook.com/

  http://www.Facebook.com/login.php

  http://www.Facebook.com/Farmville

  What antivirus/antispyware/security products do you have on the machine? Be one you have
  EVER had on this machine, including those you have uninstalled (they leave leftovers behind which)
  may cause strange problems).

  If no joy there's something blocking perhaps.

  Start - All Programs - Accessories - System Tools - IE with no Addons - what works best?

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security tab - click on reset all default areas - apply / OK

  Close and restart IE or IE with no addons

  not better?

  IE - tools - manage Addons (for sure disable SSV2 if she's here, it is no longer necessary but Java
  installs and it causes more questions - have you never update Java to go back in and turn it off again.) Search
  other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look
  right. Allowed are usually OK and "unauthorized" are not always bad. If doubt about a program
  ask about it here.

  Could not be a free - SpyBHOremover - BHO - standalone program, needs no installation, download.
  unzip and run - all are not bad, but some can cause your question (toolbars are BHO).
  http://securityxploded.com/bhoremover.php

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  Also get Malwarebytes - free - use as scanner only.

  http://www.Malwarebytes.org/

  ------------------------------------------------------

  Maybe using Compatibility Mode will help you.

  Introduction of compatibility view
  http://blogs.msdn.com/ie/archive/2008/08/27/introducing-compatibility-view.aspx

  http://www.Microsoft.com/Windows/Internet-Explorer/features/easier.aspx

  Some Web sites are not displayed correctly or work correctly in Windows Internet
  Explorer 8
  http://support.Microsoft.com/kb/956197

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Scanning with HP all-in-one printer with fax and scan Windows in Windows 8

  When you install a printer driver in Windows 8, you can scan from your computer without having to install any additional software to HP. This is particularly useful if you want to or not does not require the full functionality software or if your printer does not have a driver to scan for Windows 8.

  Windows Fax and Scan uses a Microsoft Service called WIA (Windows Image Acquisition) to capture an image from the scanner and allow you to save without the need for additional drivers.

  In addition, Windows Fax and Scan cannot scan to PDF.

  Learn how to analyze with your all-in-one printer from HP using Windows Fax and Scan.

  If you have problems using Windows Fax and scan with Windows 8 make a post below. I hope this helps anyone looking for an alternative method of scanning in Windows 8.

• Pavilion 15 laptop: problems with stop and "standby" mode.

  I upgraded from windows 8.1 for windows 64 bit home 10. I had problems with stop and goes into sleep mode and cannot be resolved, then I reinstalled windows 10. Everything worked fine for a few moments, and then the same problem reappeared. I can't stop or put my PC into sleep mode, unless I have first of all to make a restart. After a reboot, I am able to stop or go to sleep mode without problem. If I try to do either without a restart, the screen goes black and the indicator light remains lit. The only way I can get it to start then press on and hold the power button and force a shutdown down, then press the power button to restart the upward. I have another PC, a wafer think that Lenovox has been upgraded to windows Windows 7 10. This PC work fine with windows 10, no problem at all. It's just the HP Pavilion 15 who has these questions. It makes me crazy.

  Look through the tool of troubleshooting possible solutions here:

  http://support.HP.com/us-en/document/c03383935

• Error with SwfLoader and field of application

  Hello

  I have a test with a SWFLoader loading of an application in a different application domain.

  Test with SWFLoader is ok during the loading of the application in the same application domain, but when I want a new Application domain, I have an error with a debug version of flahplayer message when I use the unload method.

  Is this a bug?

  Well, I can reproduce this.

  Have seen, as I can now reproduce outside of FlexUnit however. It seems the specific problem with the FU framework is when we add it to the container of UIImpersonator, the Manager of bridgeToFocus is never properly created internally.

  I can create the same circumstances in a regular application too if I followed a similar trend. Eager to focus on this more but maybe need a loop in other countries, so I don't think it's a quick fix.

  When you have time, please this file as a bug in jira FlexUnit. Adobe is off this week, it will be at least next week before I can get a review on some of my proposed corrections.

  Mike

• Photosmart 5520: Scan to email: server connection error 403 (with app and scan)

  I scanned to send several times than I can count, but a few days ago, I get nothing other than the error "connection server 403 error." I checked the forums and someone said to go into apps and download the application. It did not work. I rebooted and tried everything, which he expects. Yet, nothing. Is this error to do with something outside as the real servers HPs - or is this something internal that I can fix it? I went as far as I can without resetting to factory settings (which I am fearful because I recently had the country code has changed on this issue and do not want to return to the country of origin), someone has any suggestions other than what I've sifted through the forums already?

  Hey @fruitfly20,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I understand that you have some problems with the scan to E-mail on your Photosmart 5520. I can help with that.

  We can try I couldn't see you is to remove and enable web services. To do:

  1. On the printer, click web services icon that looks like a tablet with a phone beside her.
  2. Click settings.
  3. Click on delete Web Services.
  4. Click again on the Web Services.
  5. Click on accept and Yes.
  6. Try scanning to Email.

  I would like to know if it works. If it does please not then let me know and we can try something else. Even if it solves your problems, so please let other users of the forum know clicking on accept as Solution below my post.

  I hope this helps and I hope you have a nice day!

• Why do I get error 66 with cRIO and STM library after 6 hours

  I have a RT (for the cRIO-9004 controller) software and a host software (on my development computer) which Exchange data through the STM library. Everything works fine, but after about 6 hours, the host stops with a message 'error 66 in STM Read Msg.vi'. Why does this happen? I use LV 8.2 and the STM 1.0.32 library.

  Thanks in advance.

  Hi all,.

  would it not possible to send your project RT together in order to test it. Make sure that the SubVIs are included. Thank you! Perhaps one of the possible reasons for your error is that your VI uses 100% of the capacity of the CPU for communication over TCP/IP breaks down due to a leak of resources, because the priority of the screw is higher. Check the use of the CPU resources when running.

  Concerning

  Greg

• hp2540: error with Hp2540 series scanning AirPrint

  I'm trying to scan documents and I get the following text:

  Scan reported that an error HP2540 series is currently unavailable. Please check if it is connected or turned on and try again later

  I went into the settings and I couldn't do anything with computer scan but Webscan seemed available but I don't know what it is. I tried it, it seemed to scan but there is no option to save. So I do not know if it is scanned or where to find the documents. I did turn off the printer and turn it back on. This sometimes happens, and there is no rhyme or reason to when and why as far as I can tell.

  Any ideas on how to get it to work again?

  Hi @clenny,

  Welcome to the HP Forums!

  I understand that you can not scan with your printer HP Deskjet 2540 on Mac OS X. I'm happy to discuss this issue scan for you!

  A few questions for beginners:

  1. You are able to make copies with your printer? Copy the text or mixed Documents.
  2. What version of Mac OS X are you using? If you do not know the operating system you are using, please visit this site. Whatsmyos.
  3. How is the printer connected? USB or wireless?

  In the meantime, please consult this guide to scanning, 'inaccessible Scanner' or ' year error occurred while scanning "message for HP Deskjet 1510, 2540 Deskjet, Deskjet Ink Advantage 1510 and series printer Deskjet Ink Advantage 2545.

  Hope this helps, and hope to hear from you soon!

• Calibration shunt 9235 with 9144 in Scan Mode

  Hey everybody,

  I use two 9144 s and a 9074 and I am trying to create a routine calibration of shunt for 12 9235 s (4 per chassis). I found this article on how to shunt calibration with the 9144 and a 9237, but it does not work:

  http://digital.NI.com/public.nsf/allkb/12017868777480AE862579BA004F0877

  This is the error I get:

  Error 65723 appeared to node (arg 1) property in the Shunt Cal 9235's.vi
  Possible reasons:
  CompactRIO: This module cannot be configured when the engine of the controller is in its current mode.

  The thing I don't understand is that the modules on the 9074 calibrate correctly, but when I try to calibrate a channel on one of the 9144 s, I get this error. I couldn't find much about this error, I was wondering if someone could help me and point me in the right direction.

  I have attached my code. It is relatively simple, and I don't see where the problem would be. I have to manually set the mode of the 9144 something than what it is currently (i.e. Active configuration)?

  Thank you for your help,

  Seth

  Your system may start in Active mode by default. This mode does not allow to set the properties of your ECAT 9144 chassis. the chassis must be in configuration mode to enable the derivation property. See attached changed VI.

  DirkW

• Journ.E - error with Digitalclock and Gutenberg App of the virtual store

  Hello!

  I have a new Journ.E, model px1530u-1et1 name, with the latest firmware installed.
  I downloaded an installed the app clock and gutenberg digital online store.
  The two won´t works correctly.

  During the opening of gutenberg and the search for something, I get an error message when you try to open one of the search results (an unexpected error in gutenberg.exe - must close the program).

  When you try to open the digital clock application, only an error message is displayed (unexpected error in digitalclock.exe - must close the program).

  If another installation, or a reboot has any effect.
  Can someone help, please

  Greetings
  Holger

  There may be some problems of compatibility with these applications
  Maybe you put the Journ.E to factory settings and should try to install the two new

• More strange problem with keyboard and mouse on Satellite 1900

  Clicking on files or folders, I wonder to confirm the deletion of the clicked elements. The "Left shift" is interpreted as a backspace. I was afraid of a virus; but no viruses or spyware are present. I reformatted and reinstalled evrything; the problem persists. Everyone has known and resolved this strange problem.
  Thank you for the help.

  Hello

  It's very strange. Unfortunately I have no precise explanation. I suggest you check this with external keyboard to see if the keyboard is not defective.

• HP Pavilion g6-1232sl Notebook: error with Win7 and AMD Radeon HD 43 7400

  Hello

  After you have reinstalled Win7 64 on my HP Pavilion laptop 1232sl g6, I get error 43 with the AMD Radeeon HD 7400 Appliance.

  I have download and installed an update of the driver from the site of AMD, but this does not resolve the issue.

  Any suggestions?

  BTW, the reinstallation of Win7 the 'sleep' feature is no longer available (it is gray). Can it be related to error 43?

  Thank you

  Giovanni

  Hi@inascargio,

  Thank you for your response.  Yes, it is important to remove the existing drivers first and then restart the computer to make it work. Please try again and proceed exactly as I have laid out for you. As you already have the driver downloaded, you can omit the first step.