switch the computer on himself

Similar Questions

• Why is my computer going himself in the middle of the night?

  After that he died during the day the computer turns himself at any point on a regular basis.  Some days it does not turn itself at all.  How can I stopthis occur?

  Hi edbths,
   
  This problem occurs if there is a scheduled task for the computer to shut down and restart at a specific time.

   

  Delete the scheduled task for this problem.

   

  Refer to the section "deleting scheduled tasks" in the following article to resolve this issue.

   

  How to modify the scheduled tasks in Windows XP

• Example: HPcompaq mintower7900: can not start the computer

  Hi all

  I need help from anyone who helps, when I try to start my computer by pressing the power button, the first time it starts and all the fun of but only run it for the fun of a few seconds then stops. When I remove the battery, CMOS and RAM for about 5 minutes and then put back them. When I start it starts well. When I try to restart, it restarts fine, but when I turn it on turn off it starts and all the fun of but only run it for a few seconds the amusements stops and nothing is visible on the screen.

  I tried to replace the RAM and CMOS, but it always behaves in the same way. My computer is HP Compaq 7900 Mini-Tower Core 2 duo. I'll be happy if my problem is solved.

  Finally, I found the solution. The problem was the switch, when I changed the switch, the computer was fine to start normally.

• roar of hard disk and the computer freezes for a few seconds

  My hard drive makes a sound whirring for a few weeks now and when I type in emails or messages like this, the computer freezes for a few seconds. Any ideas how to fix this?

  A desktop computer. Your problem could be overheating.

  You must remove the side panel right and remove dirt dust bunnies fans. Also, make sure that all the fans are working. Safety switch the computer off and pull the power cable before removing the side panel. You can then move the computer backon and check that the fans are working.

  Then, turn off the computer and some time for that cool. It is best to use a wrist band, which you set on the casing of the computer to you the earth before touching anything inside the envelope. You can buy one in a store of computer accessories. Static electricity can damage a motherboard if you don't take precautions.

  Then, you use a small brush to remove the sheep of dust around the fan on the processor. I used an electric razor, cleaning brush. I use an Air blower to clean the power supply fan. An air Duster is also useful fopr cleaning keyboards.

  Removal of the dust bunnies should reduce the noise that makes your computer. It can also reduce overheating, which can lead to errors of Blue Screen of Death.

  Another way to check the hard disk to see if it is overheating is to use HD Tune 2.55 (free):
  http://www.hdtune.com/download.html

  You have to scroll the page to see the freeware version.

• Have 2 printers on the computer and the PC will not print one when you switch to the other?

  Have 2 printers on the computer and the PC will not print one when you switch to the other?

  Having a printer at the office and one at home, but use the same PC for both? Unable to print at home after bring you it to the office (and vice versa)?

  If you USB, most of the time, the PC will recognize what printer is which. Sometimes PORTS does not commute. You can manually change the correct ports if necessary.

  CLICK ON THE MENU START

  1 devices and printers

  2 right CLICK on the printer

  3. choose the PRINTER PROPERTIES

  4. click on PORTS

  5. There will be a list of ports with one (checked marked). If it's on the wrong port, change to the right pair and choose APPLY.

  (NOTE: it must ALWAYS be on a USB port or a wireless connection.) Some ports wireless start with a #(adresse IP) or a SERIAL number)

  I hope this helps. Sometimes, you can create your own port if you have more questions.

• My Vista crashed and I've switched back to XP. Now I have 1mil more old files compressed that I can't get rid of and it slows down the computer. How can I get rid of these files

  My Vista crashed and I've switched back to XP. Now I have 1mil more old files compressed that I can't get rid of and it slows down the computer. How can I get rid of these files.

  Hello

  1 are. what type of files?
  2. when they are stored?

  3. What is the size of these compressed files?

  Try to perform the clean boot on the computer and check if that helps.

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  See the bottom of the articles that might help you resolve this problem.
  How to make a computer faster: 6 ways to speed up your PC
  http://www.Microsoft.com/atwork/maintenance/speed.aspx
  Slow PC? Optimize your computer for peak performance
  http://www.Microsoft.com/athome/Setup/optimize.aspx

• my program of creative suite 3 works on the computer of windows Home premium 64 bit? I need to switch computers because my current pc is windows xp

  my program of creative suite 3 works on the computer of windows Home premium 64 bit? I need to switch computers because my current pc is windows xp

  Yes, but you may need to use compatibility mode to install.

• The computer date went before a day, switched back and now Firefox will not record history.

  Hey guys! My brothers and sisters have decided to play a trick on me and changed my computer to the front of a week time (panic ensued). I changed it to the current date, 07/30/2104 21:18 (at time of writing), and now Firefox will not trace of my story. Just one day, I changed the time on the computer to the front and then Firefox will begin to record history. Changed, there again at the present time and also return one day and it will not save. Story work for Google Chrome and Internet Explorer.

  TL:Dr - Firefox became the TARDIS and stepped forward in time to save the history.

  Hello

  Some Firefox problems can be solved by performing a clean reinstall. This means that you remove Firefox program files, and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  More information on the resettlement of Firefox can be found here.

  WARNING: Do not use an uninstaller to third parties as part of this process. This could permanently delete your Firefox profile data, including but not limited to, extensions, cache, cookies, bookmarks, personal settings and passwords saved. They can be retrieved easily unless they have been backed up on an external device! See back up and restore the information contained in the profiles of Firefox.

  Please report to say if this helped you!

  Thank you.

• Unable to start the computer by using the power switch - y480

  Recently, I bought the Ideapad Y480.

  I could not start the computer using the power button. I had to use the oneKey recovery to start the computer and restart the system in the recovery menu to restart the computer.

  What should I do now?

  
  

• After downloading IE8; Smart screen filter not available; scroll locks; Restart computer warning on the computer to be switched on must restart; pop-up-stuck in tools has a red circle with a slash;

  After downloading IE8 the following has occurred and is ongoing.1. After the computer if initialization is complete it is a box indicating the computer must be restarted. 2. in the task bar, there is a white window with a red x'd circle outside. When you rest the mouse on the space of States of information; The SmartScreen filter can not check this website because the Microsoft online service is temporaily unavailable.3.Scrolling hang up issue where you are.4.Can is no longer display images or images on attachments to emails. 5 lost all my info auto-fill.

  Quote your full version of Windows (for example, WinXP SP3;) Vista 64 - bit SP2; Win7 RC. Win7) when you post in a forum or a newsgroup. Please do it in your next reply.

  The behavior persists after uninstalling IE8?

  How to uninstall or remove Internet Explorer 8
     http://support.Microsoft.com/kb/957700

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?  Who were these applications that run in the background when you installed IE8?

  A (another) Norton or McAfee application has already been installed on this machine (for example, a free trial version which is preinstalled when you bought it)?

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• I am meeting the computer is shut down or stopping himself?

  while I'm on my desk one another in a few minutes the computer suddenly stop. And what is the red line graph in the TASK MANAGER > PROCESS

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:

  Start the computer in safe mode and check if the same problem occurs:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Method 2:

  I suggest that you try to perform the clean boot and check:

  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• Not sure if the computer shuts down on himself after 20 minutes of inactivity.

  Original title: pc stops some way?

  problems with a dell Windows vista pc. When not used for 20 minutes, the PC seems somehow closing mode, it is to say screen turns off and does not respond to any tax, but fans of the pc can still hear running. Just don't know what it is any help would be great

  Thanks for your help

  Matt

  Hello

  ·         Since when are you facing this problem?

  ·         How do you start the computer again?

  I suggest you follow the steps mentioned below:

  Method 1:

  Disable power options sleep. Follow these steps and check if the issue persists:

  a. open Power Options by clicking the Start button, clicking Control Panel, clicking system and Maintenance, and then clicking Power Options.

  b. on the page select a power plan , click change plan settings under the plan selected.

  c. on the plan of the page change the settings, click change advanced power settings.

  d. the tab Advanced settings , buttons power and lid, expand the menu power start button, and then click setting, click the arrow and expand on sleep.

  e. click OKand then click save changes.

  Method 2:

  Update control and driver graphics card if the problem persists. Follow the steps in the link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Length of look at a time before the computer switches mode "Eve"

  original title: length of time to listen.

  My question is very similar to Marmota2, except that I do it only 2 minutes before I lose Visual but not to the screen saver, he falls asleep! It is a very recent problem. What is going on?

  Hello

  
  You did changes to the computer before the show?

  Method 1:
  You can increase the time to turn off the display and put the computer to sleep in power options.
  Check out the link:
  http://Windows.Microsoft.com/en-us/Windows7/products/features/power-management
  
  Method 2:
  You can try to change the power management and check if that helps. For more information on power management, follow the link below.
  http://Windows.Microsoft.com/en-us/Windows7/change-create-or-delete-a-power-plan-scheme

  See also the link for help:
  http://Windows.Microsoft.com/en-us/Windows7/change-screen-saver

• Switches to color when you restart the computer profile or wakes from sleep

  I bought a Dell Inspiron 1470 with Windows 7 at home as a backup of my MacBook Pro.  I used the Spyder2Express to calibrate my screen that works well.  After that I restarted my PC the color profile has been enabled for a few short seconds, but then returned to the default setting, which is horribly blue and too bright.

  I then removed the color profile created by my Spyder2Express and used Windows' built in the calibration of the monitor.  Yet once, it worked until I rebooted the computer, or he woke from sleep mode.

  I then wen to the control panel-->--> the color management advanced and assured the new profile is the default value of the system.  The problem still remained after the computer is restarted.

  The only solution I have found so far is if after I restarted my pc I go to Panel of--> of color management and select and clear the checkbox "use my settings for this device."  My profile will then return until I restart the next time.

  As a pro photographer, it is a question that is extremely disappointing.  I searched forums, web, called Dell directly and none of this was of no help.  Any thoughts?

  Hi Mike,.

  It seems that software Spyder2Express adds color profile after each reboot. We can check if really Spyder2Express is the origin of the problem
  
  Method 1:
  Uninstall Spyder 2 express and check if the return of the issue after each reboot.
  
  Method 2:
  Configure the computer to boot and then refine the boot entry that is causing the problem
  
  Step 1: Perform a clean boot:
  Note If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.
  a. log in the computer using an account with administrator rights.
  b. Click Start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.
  c. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  d. under the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)
  e. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all.
  Note following this step lets Microsoft services continue to operate. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.
  f. click OK and then click on restart.

  Step 2: Enable half the services
  
  a. click on the Services tab and then click to select the skin all the Microsoft services checkbox.
  b. Click to select half of the check boxes in the Service list.
  c. click OK and then click on restart.
   
  Solve the problem:
  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  Reset the computer to start as usual:
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  a. Click Start, type msconfig.exe in the start search box and press ENTER.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  On the general tab, click the Normal startup option, and then click OK.
  When you are prompted to restart the computer, click on restart.

  All the steps above to perform the clean boot is mentioned in the following article
  http://support.Microsoft.com/kb/929135

  Hope this helps,
  A Mir.

• switch the printer on the computer

  Re HP8600 Pro

  The Control Panel does not light and I can print only.  HP told me that it is a hardware problem which has not been addressed and was told to buy a new printer.  I know that it is possible to set the options of the Control Panel on the computer.  Can someone tell me how?  There has been no change in system, and I tried ALL of the suggestions that I could find.  I can't afford to buy a new printer, and it is less than two years.  Thank you for helping us to be a non-techie!  (I am not a student). ?

  Hi mek0,

  I'm going to assume you have Windows 7, here is a document for how Scan: Windows 7 with or without the HP software.

  You can do the scanning and the fax from the Printer Wizard so it's an icon that looks like the printer on your desktop.

  I hope this helps, let me know if you have any other questions.

  Thank you