System of iDRAC settings profile attribute - thermal

Similar Questions

• 1000V - Importance of the ' system vlan "in port-profile

  Hi all

  Can someone help me understand the importance of the command "system vlan" in a profile of port?

  As I understand it, it was used to mark the criticisms of the system VLAN (package, data, etc.) to their config was pushed to vCenter so that they would continue to work the MSM should be down. Is this fair?

  All of the examples I have watch seems to just mark every VLAN (data VM even VLAN) as "system vlan" in their profiles of prot ethernet uplink. Now that is best practice?

  In addition, there is a reason to mark vEthernet with control panel ports vlan?

  See you soon,.

  P

  As you already wear that system vlan is to ensure access to the vlan vsm to go down and then the esxi host is reset. If the system vlan was not enabled host esxi would not be able to talk to the vsm, but this is only the case if the management port using the Cisco VDS and not a VSS or VDS.

  as I mainly use servers with only 2 ports 10 GB I use system VLAN for ESXi management / storage and vMotion and if the vCenter is a virtual machine, then also the vlan that uses. all other VLANS I don't not in the category system VLAN.

  I use also a VSM Layer 3 so no need to worry the VLAN the packet and data.  But I use that I have several farms esxi in a different subnets from the management and the 1000v in a subnet for network management.

  I hope this helps.

• Configure the IDRAC settings without having to restart the server

  We have a dell r610. I put an IP address in its idrac last night and ping it, then powered by the server. Today, I can't ping the IP address of the idrac. Put aside from getting to the site, restart the machine and go into the settings of idrac way, is there a way you can access these settings and make changes while the server is in place?

  Hello Roger

  Yes, as long as you have a way to access the system. If you have the operating system remotely, you can install OpenManage Server Administrator. OMSA has an iDRAC section where you can change the IP address of the iDRAC.

  OMSA installation also installs the RACADM tools, so you will be able to execute RACADM commands as well. You can use the RACADM commands to perform all the tasks that you can do so via the GUI, some which are not available in the GUI.

  When you get OMSA is installed, you can check the status of the components of the system. If you see any problems then I would suggest that your first troubleshooting step be restart iDRAC. You can restart the iDRAC independent of the system, there will be no interruption of service to the server when you restart the iDRAC. The command RACADM to restart the iDRAC is:

  racadm racreset

  The command RACADM to iDRAC default configuration is:

  racadm racresetcfg

  Thank you

• Cannot change network iDRAC settings 7

  Hello

  I am trying to set up alerts e-mail for a few servers and have encountered a problem with the network settings on the iDRAC. The problem is that the DNS settings is not configured correctly on most of the servers, which would require me to use the direct IP to my SMTP server, that I prefer not to even if it would work. I have also some machine with an incorrect host name value that before email alerts has been only a slight cosmetic problem in the interface.

  When I try to change the settings on the network tab in the iDRAC charging page interface with old settings just once I hit apply. There is a note on the top of the page that tells me that the NETWORK card must be reset to apply the settings, but settings will still apply after reset of the iDRAC together.

  Hi AlbinG,

  Can you give us more details

  1: what server do you use?

  2: iDRAC FW Version

  3: what setting all you changed on the iDRAC network page.

  4: do you have any VLAN configured on iDRAC?

  5: what operating system and browser you use to launch the iDRAC Web Interface?

  Any network on iDRAC7 setting will take 30 to 60 seconds to apply. Can you wait 60 seconds and refresh the page and see if the changes are applied. There is no need to reset the iDRAC to apply the setting.

• Why can't I just copy a profile to another system in the directory profiles and modified the ini file

  My main system crashed. I have a copy of the profile. When I move a copy of the profile in the profiles folder and edit the ini file to use the new name, I get a message that there is an instance of thunderbird running and I need to shut it down. I don't see any instance of thunderbird anywhere in the Task Manager. It happens just for me the fact that I am also in firefox may be the cause of the problem to a running instance. I'm under V31.7.0

  I tried to simply move the mail directory in the existing profile. The thing is that I don't see the old messages. I can see all of the subfolders of the Inbox on the left but not messages in the right pain. I can see new messages, but it's all in the Inbox and not filtered to the subfolder.

  I tried to activate the function of multiple profile but that doesn't seem to work.

  MY BAD
  It seems that I had something that was bad in the profile. I got the profile from a backup and now Thunderbird works fine.

  Sorry that I missed the problem earlier.

• Custom Sidebar settings / profile manager / El Cap

  Hello

  This has been a bug for some time bear.  Basically, I want to customize my file sidebar.plist for my managed network users.   Manager profile account settings 'finder '.  If I upload my sidebar.plist to the profile under custom settings manager, it seems to be ignored.

  Ive tried this on users and groups of devices.  Did anyone had success with this?

  Anyone running custom framed?  I would be very surprised if everyone is happy with the default view.

• Z220 CMT Workstation: restore the system to factory settings.

  Model: Hp Z220 CMT Workstation
  OS: Windows 7 Professional
  
  I'm trying to restore my computer to factory settings. I pressed ESC several times at the start to the top of the computer. Select the system restore, but the computer just hoot to Windows form. I can not connect to windows, because as some error loading windows.
  
  Is there another way for me to restore the system to factory with a clean Windows 7?

  > is there a way for me to get the recovery disk?

  Two ways:

  1. in Windows system work, running the same version (32-bit? 64-bit?), you can burn a disc of "recovery."

  2. find a friend with a 'detail' in the Windows 7 operating system DVD (remember this is the same 32-bit or 64-bit, your system) and borrow the DVD of him/her, or get him or her to burn a copy of it.

• Satellite L750-14R - network and system restore factory settings

  Hello

  I have a Toshiba Satellite L750-14R.
  He did some updates of windows, as a result, it that the wifi does not work, I had to plug in a cable to internet. Ive tried the system restore, but that has not solved. Now to work it won't work when I use the internet cable

  Try to do a restore to factory settings, ive now tried the button "0" at the start, but I get nothing it just starts up.

  I have Windows 8 on that but reinstated to the class shell Windows.
  I found in the operative setting a dubious wifi adapter, I rolled it back to the previous version, I can now see some possible wifi options, but still if I now add cable icant get all internet.

  I totally want to reset the settings to factory, but unable to do?

  Try to do a restore to factory settings, ive now tried the button "0" at the start, but I get nothing it just starts up.
  I totally want to reset the settings to factory, but unable to do?

  You said this system Win 8 lance on this laptop.
  As far as I know this laptop Satellite L750D-14R was pre-installed with Win 7 64 bit OS.
  This means that the HARD drive recovery process does not work because the contents of the HARD drive and partitions have been changed!

  To retrieve the computer laptop back to factory settings, you should the Toshiba Recovery disk/medium. If you have not created this disk then you can order it here:
  http://backupmedia.Toshiba.EU/

  In any case, I guess that the connection to the LAN does not work due to driver LAN problem.
  I recommend you to uninstall the network driver (in Device Manager) and download the latest driver LAN available from the Toshiba UE driver page.

  After installation of the driver LAN restart the laptop.

• Several user under Documents and Settings profiles

  I have several machines to Windows XP Pro SP3 with several user profiles in the Documents and Settings folder.  My pc is one of them.  I have tvavra, tvavra. ASL, tvavra. ASL.000 and tvavra.ComputerName.  I understand that some of the accounts are created when mistakes happen, but I would like to have a procedure to clean the files.  Most often the reason why these folders are created first is when a user logs on the machine of someone else, they should draw these records.  I recently needed to redistribute machines in a campaign of savings and if I can eliminate clutter, I'd be very happy to help.

  The old profiles that are not currently in use are safe to remove. You can find your current profile by opening the folder my documents on the start menu and search in the address bar. You can check in each to make sure there are no files which are necessary for the first.

• Cannot access my account and I am the administrator of the system. The user profile cannot be loaded

  I can't log into my account. I am the administrator of the system account, but he said: "the service user profile Service has no log on." User profile cannot be loaded. Any suggestions? I can connect to other accounts, but they are not administrative accounts.

  ·                         Restore point:

  Do in Mode safe, if necessary.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  See you soon.

  Mick Murphy - Microsoft partner

• Group of system cache emptied auto Extended attributes/Custom Sections (prodikaadmin) account

  
  We knew that person logged in as that of our prodikaadmin system account, but in the regular Cache Flush line waiting, it shows empty prodikaadmin the cache of extended attributes/Custom Sections. I want to check if this could be automatically triggered if you rinse manually or we have concern for safety.

  I think it started with 6.1 or 6.11 but yes, the Portal do, Admin and expanded Sections attributes/Custom auto-cache hunting now.

  Hope that helps.

• Desktop PC: how to restore my system to factory settings

  I need to restore my PC to the original factory settings, how do I do this?

  Thank you

  Bill

  HP Recovery Manager can be accessd in the Start Menu or by pressing the F11 key immediately after switch on/off the PC. Recovery Manager is used to reinstall specs_also of plant used to manufacture the defined recovery disk.

  HP has documents explaining the process for... Vista, Windows 7, Windows 8 and Windows 10 found here:

  http://support.HP.com/us-en/document/c00006110

• Laptop: how to restore my system to factory settings

  I need to restore my PC to the original factory settings, how do I do this?

  Thank you

  Bill

  HP Recovery Manager can be accessd in the Start Menu or by pressing the F11 key immediately after turning off the computer. Recovery Manager is used to reinstall specs_also to factory used to make recovery media.

  HP has documents explaining the process for... Vista, Windows 7, Windows 8 and Windows 10 found here:

  http://support.HP.com/us-en/document/c00006110

• System preferences network settings

  I can't open my network preferences.

  I get the following error:

  Dutch: Het voorkeurenpaneel 'Netwerk' kan niet worden loading

  English: Failed to load control panel preferences 'network '.

  Screenshot: http://puu.sh/mtGN1.png

  Any idea what would cause this?

  Please triple - click anywhere in the line below on this page to select:

  /Library/Preferences/SystemConfiguration

  A right click or Ctrl-click on the line and select

  Services ▹ Open

  the contextual menu.* should open a folder named "SystemConfiguration. Move the contents of this folder to the trash, except the file with this name:

  com.apple.Boot.plist

  Let this file where it is.

  You may be prompted for administrator login password. Restart the computer and test.

  If there is no change, restore each of the items that you have deleted from a backup, crushing the that may have been created in its place.

  If the problem is resolved, you may need to recreate some of your settings in the network preferences panes and energy saving.

  * If you do not see the item context menu copy the selected text in the Clipboard by pressing Control-C key combination. In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

• c:/documents and settings / * profile name * in accessible___access not denied

  What does the message above?

  Ruby101,

  Welcome to the Microsoft Answers community.

  This problem occurs because the security of the user ID has changed. Even if you use the same user name and password, your security ID no longer matches the security ID of the owner of the folder that you cannot open.

  To resolve this problem, you must turn off Simple file sharing, and then take ownership of the folder:

  1. disable the option Simple file sharing:

  a. click Startand then click my computer.

  b. on the Tools menu, click on Folder Optionsand then click the view tab.

  c. under Advanced settings, clear the use simple file (recommended) sharing and then click OK.

  2 right click on the folder you want to take control and then click Properties.

  3. click on the tab Security and then click OK in the Security message, if an unknown device appears.

  4. click on Advancedand then click the owner tab.

  5. in the name list, click your user name, administrator , if you are logged in as administrator, or click the Administrators group.

  If you want to take ownership of the contents of this folder, click to select the check box Replace owner of subcontainers and objects .

  6. click on OK.

  You may receive the following error message, where folder is the name of the folder you want to take care of:

  You are not allowed to read the contents of directory folder. Do you want to replace the the directory permissions with permissions granting you full control? All permissions will be replaced if you press Yes.

  7. click on Yes.

  8. click on OKand then reapply the permissions and security settings that you want for the folder and the contents of the folder.

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.