table changes not recorded

Similar Questions

• Rich Table: entity validation fails, but the user can change the record! : O

  Hello
  I develop with JDeveloper 11.1.2.1.0 and I have the following problem. I have a rich table editable according to entity/view with a line entity level validator method that checks the consistency of rank according to custom rules.
  I noticed that if the validator fails, the error message is displayed correctly, but it is possible to move to a different folder and this causes a lot of problems. I need avoid recording of variation when this validator fails. I know there is a way to block navigation on an element using clientListener and javascript, but it's a different need because I don't want the user to change the recording while the validator fails.
  How can I do?
  Thank you
  
  Roberto

  Roberto R SCC wrote:
  I noticed that if the validator fails, the error message is displayed correctly, but it is possible to move to a different folder and this causes a lot of problems. I need avoid recording of variation when this validator fails. I > know there is a way to block navigation on an element using clientListener and javascript, but it's a different need because I don't want the user to change the recording while the validator fails.
  How can I do?

  When you change a line, it is the currentRow on the iterator. You do not want any line to become the currentRow.
  I would go to this topic, in this way: substitute the selectionListener table and the listener to custom selection, check if the current currentRow (the one you are editing) isValid (EntityImpl::isValid).
  Proceed with the treatment of the selection event only if it is validated... You could even show an error or a warning message asking the user to provide valid data and even commit the line before choosing another.
  (Sorry, don't have an example of a code of practice now)

• Im trying to buy photoshop but it keeps saying that its not available in my area. I am in the United States and in my area gets bad! I even updated to the United States, but it is not record the change!

  Im trying to buy photoshop but it keeps saying that its not available in my area. I am in the United States and in my area gets bad! I even updated to the United States, but it is not record the change!

  Hi Mariam,

  It seems that your ID Adobe was initially registered in Pakistan due to which it is not allowing you to make purchases in the United States.

  You can create a new Adobe ID, register in the United States and then it should allow you to make a purchase.

  Let us know if it works or not.

  Thank you

  Yann Arora

• Differentiate the tables changes and no changes do not

  Hello
  
  I am relatively new on (I've always been a sort of paper/felt for Whiteboard guy) formal data modeling tools.
  
  On my question/Scenario:
  
  I have a warehouse of data with a few hundred tables inside. When changes are made to the data warehouse, we're supposed to present an ER diagram preferably with tables in one color, tables be changed to a different color and the tables does not change does not to another more neutral color.
  
  Here is my current process
  
  (1) import of relevant existing tables in the data dictionary
  (2) create tables or change existing tables
  (3) change the type of array for the modified tables and dimension for new tables. The existing tables, I leave it as what.
  
  Success with this process generates a diagram that fits my purposes, but I have a hunch that I'm not using better methodology. What is a better way to do this using the oracle sql data model (version 3)

  What you certainly works, but a better approach would be to define new types of classification rather than use the Dimension or fact.

  Then go here:
  Tools-> preferences-> data-> diagram maker-> Types of Classification.

  Press the Green plus sign to add a new type.
  Add two new types: new and changed and assign each a unique color.
  Press 'OK' to save.

  Now, when you go back to the diagram, you will have two new types from.

• AF:table does not display the records to make the updating of the view object iter

  Hi Experts,
  
  I use JDeveloper 11.1.1.4 and I have a page that shows a view object records one particular reading as an af:table. When I run the page to everything first he shows all the data at all. But there are 2 folders when I run the query that only read the view object. In my page there is a link called "Refresh" which calls the operation "Execute" in the view of my view object iterator. When I click on this link the table shows two records. Why the table shows no files once when the page is rendered?
  
  Please help me.

  Hi user,

  Yes use component query to display criteria. Please let me know if something specific I need to check when I use the query component. If you have already faced this problem please help me to solve it.

  you are looking to do this,
  http://www.4shared.com/photo/B36OTSl9/check.html

  Published by: Les on November 22, 2011 12:26 AM

• How insert/DML data in the table when the data in the related table changes

  Hello guys!
  
  I came across a problem that I need to get fixed. Because I don't know how to start and get it resolved I wanted to ask you for your expertise.
  
  The scenario is as follows:
  
  I have a table 'a' in my 10g database and a view "ab" which combined table 'a' with 'b' table in a view. However, the 'b' table is a table in another schema Manager database. and accessible (read only right) via a database link.
  
  Now here it is: whenever the data changes in table "b", for example 2 new sets of data is inserted, I need to insert automatically the 2 values of these 2 sets of data in my table "a". Same procedure for update and delete in table "b".
  
  The action that inserts data into the table 'a' must be initialized in my database, I have limited access to the other. Can I somehow use a trigger my reviews of "ab" to insert data into the table "a"? Or is it possible to use the "change notification procedure database" using the view as the reference?
  
  Desperately need help and example of all suspicion/code greatly appreciated. I am very new to Oracle and not very fond of PL/SQL routines. So please be so kind as to give me more details.
  
  Thanks in advance - I hope you have any ideas how I can get this problem resolved.
  
  Sebastian

  >

  ... it does not, since the DDL operations are not permitted on the remote databases (ORA-02021). I can't create the trigger on a view either. :-(
  So what ways are left to insert data into the table 'a' when the related table changes?

  Please, help if you have an idea!

  Yes,
  You can't perform the DDL (create the trigger...) on remote databases as you can see...
  Try to create this trigger in the local database that will make DML (insert into...) on the remote database.

      CREATE OR REPLACE TRIGGER local_forward_pt_after_insert
       AFTER INSERT
           ON N2K_INV_PT
           FOR EACH ROW
  
       BEGIN
           -- Insert records into table "a"
           INSERT INTO TBL_PUNKTDATEN@remote_database_sid
            ( INT_NUMMER,
              STR_GEBIET
               )
           VALUES
            ( :new.INT_INV_PT_NR,
              :new.GEBIET );
       END;
  

  Thank you

  Good luck

• My Sony Handycam DCR-TRV950 flashes a yellow icon, C:31:23 and will not record or play.

  A year ago, the camera suddenly started flashing and beeps a yellow icon in the middle of the screen. C:31:23 flashes in the upper right corner above the minutes from the end. The camcorder will not record or play.

  If I remove and reseat or change the battery, and if I remove and reinsert or pass the minidisk, sometimes it'll save or play for a while before the beeps happen again.

  Sunny in Sun Valley

  Try to check the pin of pinch. Open the container of band and you can see the PIN pinch, is a small black roll about 1/4 in. wide and about 1 inch in height, see if she's down on the stem

• Tecra M5 does not record the date and time - battery RTC or CMOS checksum is inconsistent

  My Tecra M5 PTM50E reverend new does not record the date and time. I loaded RTC battery for 8 hours when electricity is on in the said user's manual. I don't know where is the problem. The BIOS settings are respect after power is on.

  When I change any value in the BIOS, the changes are saved properly but date & time system restored to their value 01/01/2000, 00:00 every time when I get out of turning off more of 2-3 min. Message "RTC battery is low or CMOS checksum is inconsistent.

  Press [F1] to set Date/time"does not appear when I power on the computer. Any suggestions?

  Hi guys

  Usually this problem appears only if the CMOS (real time clock) battery is empty or corrupted.
  The real time clock battery powers the internal clock in real time and calendar. It also maintains the system configuration. If the RTC battery is completely discharged, the system loses these data and the real-time clock. In this case, the message RTC battery is low or CMOS checksum is inconsistent appears.

  So I see only two possibilities:
  Either you will charge the battery for real-time clock, or you ask the technician for replacement.

  Generally, the battery must be completely charged after 8-9 hoers but try to connect the laptop to the power adapter for a long time.
  If it will not help solve the problem if you contact the ASP for the RTC battery replacement.

• Graph of a table, but not all of the ranks of it?

  I'm graphic of a data table so that several waveforms appear on my graph of the waveform. The table has 500 lines, but I will not draw everyone, only the first row, 20th, 40th, 60th,..., 500th row. I was thinking of using a loop for to extract the lines, I need using the VI "subset of the table", but I don't know how to configure the inputs. In addition, if there is a better way, can someone let me know? Thank you!

  Had some access to LabVIEW. Something like that? For scalability, you probably want to replace the constant 500 with a function to get array size. That way if the size of your table changes, you will ensure you will always get all the data without modifying the code

  

• Built-in microphone does not record

  I have a Toshiba laptop with a built-in webcam and microphone.  For some reason, the microphone has stopped working - I can not record sound or having people hear me on Skype - if it says that it works correctly when I open Control Panel is. What should I do?

  Hi Eryx,

  You have made any changes to your computer recently?

  I suggest you to follow the steps and check if she dreams.

  Run Microsoft Fix - it for the link and if it helps.

  Diagnose and automatically fix problems audio and sound recording

• Why my microphone does not record any sound?

  So, I try to activate the sound of material & sound-> Sound-> record, succeed in that, then try to test. And my microphone does not record anything yet (I have the latest drivers), it is a headset and it is not silent. I've reconfigured it, it didn't work.

  So I tried a new micro, it worked too.
  Can you give me an answer to what is happening and how to fix it?

  Hello

  Did you change your computer before this problem?

  Try the following steps to cross check if the microphone is correct.

  a. Click Start, type mmsys.cpl in the search box and press ENTER.

  b. in the sound dialog box, click the recording tab.

  c. click Microphone, and then click Properties.

  Note: Make sure that the work appears under Microphone. If the job does not appear, click Microphone, and then click on set as default.

  d. in the properties of the Microphone dialog box, click the custom tab.

  e. turn on or off the amp Microphone check box.

  f. click the levels tab adjust the slider for the volume to the desired level and then click OK.

  g. click OK to close the sound dialog box.

  See also:

  Open the troubleshooting of Audio recording

  http://Windows.Microsoft.com/en-us/Windows7/open-the-recording-audio-Troubleshooter

  Connect one microphone, music player or other audio device to your computer http://windows.microsoft.com/en-US/windows7/Connect-a-microphone-music-player-or-other-audio-device-to-your-computer

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

• Windows Media Center does not record the calendar.

  Planning to record a program, but sometimes lapsed time up to the point where it does not record. I am running Windows 7 Home. Yes, I checked preferences but which differs only up to 15 minutes max.  I have reinstalled twice already. Why please?

  Hello

  (1) did you make any changes before the show?

  (2) what is the brand and model of the computer?

  Windows Media Center records the first home run HD programs or any which TV tuner installed. However, you may need to follow a few rules.

  -If you turn off your computer, Windows Media Center does not have a regular program. The computer must be turned on or "standby mode" to record a television show. The computer will not automatically in standby mode if Windows Media Center is open.

  
  -Make sure that you turn off the screen and lower or turn off the sound if you have one at the request of a record in the middle of the night and don't want to be disturbed.

  -Your scheduled recording may not save in the following situation: schedule you a recording in Windows Media Center to start in less than ten minutes, close Windows Media Center and put your computer into standby or hibernation mode immediately. Use or one of the following options to save your record programmed:

  a. do not close Windows Media Center before you put your computer on standby or hibernation.
  b. after having programmed a recording, wait a minute before you put the computer in standby or hibernation.

  I would have you refer to the article below:

  Why my TV did not show record in Windows Media Center?

  http://Windows.Microsoft.com/en-in/Windows7/why-didn

  Please let us know if that helps.

• WLC 2106 routing table do not fill

  Hey guys, I hope you can help with this one.

  I just tried to set up a WLC 2106 and everything seems OK however the routing table is not filled (even directly connected and default route). Currently, I have it plugged into a switch and an AP and they are all two visible in ARP and CDP, but I only ping is peripheral.

  (Cisco Controller) > show the summary

  Number of roads... 0

  Destination Netmask Gateway network

  -------------------    -------------------   -------------------

  (Cisco Controller) > show cdp neighbors detail

  -------------------------

  Device ID:-swt00.asggroup.com.au

  Enter address (s): 10.33.17.62

  Platform: cisco WS-C3750G-48TS, capacity: Switch IGMP router

  Interface: Fastethernet0/0/1, ID of Port (outgoing port): GigabitEthernet1/0/48

  Hold time: 174 s

  Version:

  Cisco IOS software, software C3750 (C3750-IPSERVICESK9-M), Version 12.2 SEE2 (25), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc., Compiled Saturday 28 July 06 12:55 by yenanh

  version of the proclamation: 1

  -------------------------

  Device ID: AP1cdf.0f95.732c

  Enter address (s): 10.33.17.10

  Platform: cisco AIR-LAP1142N-N-K9, capacity: Trans-pont

  Interface: Fastethernet0/0/7, ID of Port (outgoing port): GigabitEthernet0

  Hold time: 155 s

  Version:

  Cisco IOS software, C1140 Software (C1140-K9W8-M), Version 12.4 (21 a) JHB1 - VERSION of the SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc., Compiled Thursday, Aug 11, 10 at 15:45 by prod_rel_team

  -Other - or ITU (q)

  version of the proclamation: 1

  Configuration of the interface

  Name of the interface... ap-Manager

  MAC address... 58.8 d: 09:93:f1:c0

  IP Address....................................... 10.33.17.2

  IP Netmask....................................... 255.255.255.192

  IP Gateway....................................... 10.33.17.62

  State IP NAT outside... People with disabilities

  External IP NAT... 0.0.0.0

  VLAN............................................. 17

  Port of physics... 1

  Primary DHCP server... 10.33.17.1

  Secondary DHCP server... Not configured

  Option DHCP 82... People with disabilities

  ACL.............................................. Not configured

  AP Manager....................................... Yes

  Comments interface... NO.

  ... Management interface

  MAC address... 58.8 d: 09:93:f1:c0

  IP Address....................................... 10.33.17.1

  IP Netmask....................................... 255.255.255.192

  IP Gateway....................................... 10.33.17.62

  State IP NAT outside... People with disabilities

  External IP NAT... 0.0.0.0

  VLAN............................................. 17

  Quarantine-vlan... 0

  Port of physics... 1

  Primary DHCP server... 10.33.17.1

  Secondary DHCP server... Not configured

  Option DHCP 82... People with disabilities

  ACL.............................................. Not configured

  AP Manager....................................... NO.

  Comments interface... NO.

  Any help would be greatly appreciated
  Mark

  Hello

  Removes the brand management and interface of the AP on the WLC Manager and put the management and the Manager of the Ap in the vlan Switchports native...

  example of...

  the command is...

  WLC > config interface management vlan 0

  WLC > config interface vlan ap-Manager 0

  On the switch...

  switchport mode trunk

  switchport trunk dot1q encap

  switchport trunk vlan native 17

  end

  I assumed the management and Manager of the AP are in vlan 17. make the corresponding changes if not 17.

  Let me know if we can t oping after making the above changes...

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• How to add data to the table changed in sql developer at Apex and vice versa

  Hello

  I had tables of database with sql developer. But now, I have modified the database (new tables added + changed the data in the tables). However, in the Apex, I the old database. Is it possible to get the new Apex database with the data of the table changed so this database in both places (sql and apex developer) is exactly the same... Also the other way around.

  Thank you

  The database schema that contains the tables, is it associated with the workspace even you are searching through the APEX product t development?  Why I'm asking is, if they are the same schema, the tables that you MODIFIED should be appear in the sql for APEX workshop part.  Now reports and forms will NOT see the changes (unless you have actually added or updated definitions for column).

  Can you explain what exactly you were doing the SQL Developer to the tables in your schema?

  Thank you

  Tony Miller
  Los Alamos, NM

• transformation script changes not saved in design

  Hello

  I made several scripts processing to change my relational model to the Data Modeler.

  One of the scripts defined abbreviations of table for all the table based on the PK constraint. (I'm importing the model of my data dictionary which has PK constraints defined as {abbr} _PK)

  After I "Apply of Scripts of Transformation Custom", I see that all tables have now an abbreviation of the table.

  However, if I save my design, close and reopen it, all abbreviations are empty again.

  I did a few tests and manually fill the field of abbreviation Table changes be saved.

  If I check the table XML files, I can clearly see that the table for which I manually added the acronym has a < short > tag, which is not what I filled auto with the transfer script.

  I noticed a similar behavior for scripts that I use to fill the parameters of Auto_inrement and others. After I run the script, I can see all the values filled in my template, but is not be saved and I lose all the changes made after closing my model.

  I noticed that the changes be saved if I choose Save as and save my template in a new directory (however to register as in the same directory create a SVN error).

  Is there something I should add to my .js script that changes be saved?

  Is this a bug?

  Does anyone else have these issues?

  I use Data Modeler 4.1 early adapter on a win machine 7.

  An example of .js script I use:

  //******************************************************************************

  //

  NAME: set_table_abbreviation

  AUTHOR: NVDA - NIAUW

  OBJECTIVE: use this script to define abbreviations of table in the physical model for each table

  VERSION: 1.0

  //

  PREREQUISITES:

  -Table with PK constraint and name constraints = {table abbr} _PK - as it is in the designer

  //

  //******************************************************************************

  load compatibility to 4.1 data maker script (ea)

  Load("Nashorn:mozilla_compat.js");

  import Java packages

  importPackage (javax.swing);

  //----------------------------------------------------------

  Global declarations

  //----------------------------------------------------------

  var msg ="";

  //----------------------------------------------------------

  Main body

  //----------------------------------------------------------

  find all tables in datamodel in table

  tables = model.getTableSet () .toArray ();

  loop over the tables and do something with it

  for (var t = 0; t < tables.length; t ++) {}

  If (! table [t] .getAbbreviation ()) {}

  var abbr = setAbbrv ([t] tables);

  If (abbr! == ") {}

  tables [t] .setAbbreviation (abbr);

  tables [t] .setCommentInRDBMS ("abbreviation table: ' + abbr");

  MSG += "table" table [t] .getName () + 'got abbr' abbr + "\n";

  }

  }

  }

  inform about what happened

  If (msg! == ") {}

  JOptionPane.showMessageDialog (null, msg);

  } else {}

  JOptionPane.showMessageDialog (null, ' no table (without abbr) found.) ») ;

  }

  //----------------------------------------------------------

  Functions

  //----------------------------------------------------------

  FUNCTION: setTbleAbbrv

  //----------------------------------------------------------

  function setAbbrv (table) {}

  var = abbr "

  var s = table.getPKeys () .toArray ();

  for (var t = 0; t < constr.length; t ++) {}

  cast to string

  var strConstr = constr. [t] + '.';

  If (strConstr.match(/_PK./)) {}

  abbr = strConstr.replace var ('_PK' ");

  }

  }

  If (abbr = ") {}

  MSG += "table" + table.getName () + "is not a PK constraint. \n » ;

  }

  back to abbr;

  }

  FUNCTION: read

  //----------------------------------------------------------

  function read (pMessage) {}

  var input = JOptionPane.showInputDialog (pMessage);

  return entry;

  }

  Hello

  in the loop where you treat the tables, do the following:

  tables [t] .setDirty (true);

  This will mark the object as being edited and saved during the registration of the design.

  Joop