The engineer and the contractor interface

Similar Questions

• Need help for reading in parallel on the same interface and writing XNET

  Hello. I need help to configure CAN interface to write and read from the same interface.

  I use NI PXI-8513/2. I use CAN1 as interface.

  My had TO send status messages CAN every 100ms. I have to read in order to return akntoowlege to keep DUT CAN interface happy and not make mistakes.

  So, I want to open Strim Session and readall frames in the loop. At the same time, I need to be able to write in a frame HAD at the time...

  I only need to read one picture at a time too, but since I know the ID, I can pull it from the stream.

  What I'm confusing all is how to put in place the same CAN1 interface to be able to write and read in parallel.

  I think I would get errors that interface is already in use.

  Since I'm new to CAN, I was read and write only when necessary. But, sometimes I was getting errors on my messages. Sometimes I get message, sometimes miss me. But, when I run CAN test criminal as sniffer he sends and written every time. I was told it's because it recognizes all messages.

  I opened to suggestions of how best to implement the interface.

  I guess I can use CAN2 and separator to work around this problem, but I would use an interface if possible.

  Thank you

  Hi Rus,

  The XNET hadrware takes care of most of the low level of detials for you. The reading and writing of the circuits are both connected to the bus at any time. When you write to the hardware it will try to put a frame on the bus at the first opportunity he can. If the frame loses arbitration material re - will attempt to send the frame up is successful. Reception equipment monitor activity on the bus, regardless of what it conveys. The material received will usually throw a framework that was sent by communication equipment, but there is an Echo property pass to circumvent this behavior too.

  Take a look at the example of the expedition: MAY-> NI - XNET-> Sessions-> multiple Sessions Intro-> CAN even exit entry framework Port unique Point.vi. Keep in mind that this example you will need to use a second CAN interface to recognize frames, it transmits. I would recoment against the example CAN output Frame Single Point which would mimic your ECU if you choose a type of cyclic frame running this example.

• to access the QML attached objects in C++ and best practices for the handling of the user interface in classes

  Hello

  I have in fact 2 queries

  (1) how can we access attachedobjects defined in QML in C++?

  (2) I'm loving development on Blackberry 10 C++ is one of my favorites. But I'm a bit lost when it comes to managing the user interface in classes. For example when we create the project through momentics we have a class called ApplicationUI. It manages all the (default) user interface commands, we in C++. as for example creating the document qml and setting as root user interface, etc. I am now working on an app that have NavigationPane as root, and then I continue to push pages (like the screens). But now the code for all pages is inside my ApplicationUI. What is the best practice to keep the UI for each page logic in a separte C++ class?

  I also develop for Android that a separate class for each activity, this code does not mingle for each activity. Please guide me how can I keep logic of user interface of each Page into a separate class of C++?

  regarding your second question:
  I think this is the simplest approach to keep all things in the UI in QML. You can easily put things into separate files.

  If you want to use c ++ to the user interface: can be done, too. just put it in separate classes and include those in your application class.

• How to distinguish the physical interface and logic (subinterface) interface to the Cisco router/Switch?

  Hi Expert,

  How to distinguish the physical interface and logic (subinterface) interface to the Cisco router/Switch? Can you please clarify a formal way for this so have?

  A physical interface is numbered with the same name of the interface when printing on the physical port. For example "GigabitEthernet 0/1" corresponds to port 1 of the 0 module (or the base unit).

  A logical interface can be a subinterface on a routed port and will have a point ("". "") preceding the number sous-interface (ex. GigabitEthernet 0/1.1). It can also be a loop or a virtual interface (on a router this could also include interfaces like the tunnel and virtual tunnel or VTI types). A switch may also have a VLAN logical interfaces (e.g. interface vlan 1) which are used as layer 3 virtual interfaces of type.

• Static and VPN on the external interface

  Hello

  Can someone tell me if it is possible (and if so, how) do vpn enabled on the external interface and to have something like:

  public static x.x.x.x interface (indoor, outdoor)

  IE: I have two addresses ip - one for the router an e0 on the pix. I create a static and lists of access to allow inbound http/https server inside but I also want to allow vpn hit e0 and work. My configs work if I use an ip address 3 for the static, but not if they share. I can imagine that the static method takes the vpn traffic before the pix can use it OR maybe as the pix has no route to the now (due to the static method) that it cannot answer?

  Hope I'm making sense

  Thanks for the time spent on this

  see you soon

  Andy

  I think you want something like this:

  public static tcp (indoor, outdoor) interface http 10.10.10.10 http netmask 255.255.255.255 0 0 (where 10.10.10.10 is your web server)

  public static tcp (indoor, outdoor) interface https 10.10.10.10 https netmask 255.255.255.255 0 0

  access-list 101 permit tcp any host x.x.x.x eq 80 (where x.x.x.x is your IP interface)

  access-list 101 permit tcp any host x.x.x.x eq 443

  Access-group 101 in external interface

  It will be useful.

  Steve

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• WebVPN and anyconnect on the same interface

  Hello!!

  We have ASA 5520 firewall running with code.9.1 (2). We already have webvpn running on the firewall and has active users to use it. Now, the client came with a new requirement to configure firewalls on the same anyconnect. We have installed VPN more premium license.

  (1) is it possible to enable webvpn and anyconnect on the same interface. If Yes, what are the aspects we must consider to allow them both on the same interface?

  (2) how much webvpn and anyconnect vpn licenses should I do with my premium lincense?

  Please help on this.

  shver attached for reference.

  Best regards

  Sri

  Your peers licenses AnyConnect Premium gives you the right to access SSL VPN without customer and focused on the customer.

  Licensing is based on the concurrent users so regardless of the simultaneous dosing will work - as long as the number of connected does not exceed 100.

  Your site to site VPN IPsec does not count against this permission, but is rather against "Other peer VPNS" which does not require a separate license and is limited by the capacity of the ASA equipment (750 on your platform).

• To connect to the internal interface and access the LAN

  Hello

  I have the following problem, I have a Cisco 2811 router with a serial number and an ethernet interface. On the serial port, I have an address got from the ISP, but not a real IP address. It's a 30 ip only for communication ECCAS my site and the ISP and the ethernet I one of the addresses of my range. I have have need allow VPN connections on this address (ethernet one) and access hosts on the internal LAN.

  I am able to connect to the VPN, but I can't reach any host inside the LAN

  Is it possible to display relevant configuration

  crypto-address ethernet card must be present in the router.

  What also makes sh crypto isakmp her and sh crypto ipsec his give?

• How to get the ASA packets that come in and out on the same interface?

  Hi all

  How can I configure the ASA5520 routes the packets that come in and out on the same interface? I ve more than 1 network behind the camera of the SAA. It s separated by internal router. They can communicate with each other.

  I've seen it's PIX design problem. She applies to the platform of the ASA?

  Please advice.

  Thank you

  Nitass

  This golden rule remains immutable. the only exception is the vpn traffic. ASA for example (or pix v7) would act as a hub for traffic between two rays rediect vpn.

  regarding your question.

  Internet <-->asa <-->1 <-->lan router <-->lan 2

  assuming the host to lan 1 to asa as the gateway default, even asa has a static route to the internal router of the point for local network 2, the golden rule will reject this operation.

  one solution is to re - configure the dhcp on the LAN 1 scope and make the internal router as the default gateway; and the internal router has the asa as the default gateway.

• Public and private IPs on the same Interface by using NAT Exemption/policy NAT

  I'm looking for some feedback on whether my thoughts on the installation program will run.

  Equipment: PIX 515E 6.2 (2)

  Scenario:

  The inside interface of the PIX will host 3 blocks of addresses IP - 24 public 2 blocks and 1 private/16 block. (All IP addresses have been replaced by dummy blocks.)

  Blocks of audiences:

  * 192.168.10.0/24

  * 192.168.20.0/24

  Block of private:

  * 10.50.0.0/16

  Traffic from the public 2/24 blocks should go through the firewall without address translation.

  The two blocs of the public will be able to receive connections initiated from the Internet.

  Public blocks will need to be able to send and receive traffic on a static VPN tunnel to our headquarters without subject to address translation

  Traffic leaving the sector private/16 block should be subjected to PAT before passing through the firewall.

  Private/block 16 will not receive incoming traffic from the Internet (other than responses to outbound connections initiated from within the private block).

  However, the private block will also have to be able to send and receive traffic on a static VPN tunnel to our headquarters * without * subject to address translation (i.e. hosts on our corporate network must be able to initiate connections to the private block and vice versa).

  The inside interface of the PIX will be connected to a Catalyst 3xxx series layer 3 switch, which will be responsible for routing all internal (so the PIX will never be routing of traffic on the interface, it was received).

  My ideas on how to implement are:

  * Use the exemption of NAT to exempt public address translation blocks. This will allow incoming and outgoing connections through the firewall.

  * Use the exemption of NAT to exempt the block private NAT when connecting to our head office on the VPN tunnel.

  * Use policy NAT w / PAT to translate the block private connecting to all other hosts.

  I have translated these thoughts in the following configuration snippet.

  Because the NAT exemption is processed before policy NAT in the evaluation of the NAT rules, I believe that this should allow the public IP blocks treat incoming/outgoing traffic without translation, while submitting the private translation block (except during handling of incoming/outgoing connections to our network of corporate office).

  Can someone confirm my assumptions about this?

  # ----------------------------------------------------------------------

  traffic of # which should be exempted from translation

  permit ip 192.168.10.0 access list nat_exempt 255.255.255.0 any

  nat_exempt 192.168.20.0 ip access list allow 255.255.255.0 any

  nat_exempt ip 10.50.0.0 access list allow 255.255.0.0 10.100.0.0/16

  traffic of # which should be the subject of translation

  policy_nat ip 10.50.0.0 access list allow 255.255.0.0 any

  # Suppose 192.168.5.1 is the address to use for PAT

  Global (outside) 1 192.168.5.1

  NAT (inside) 0-list of access nat_exempt

  NAT (inside) 1 access-list policy_nat

  # assumes that 192.168.10.7 is the IP address of the inside layer 3 switch

  Route inside 192.168.10.0 255.255.255.0 192.168.10.7 1

  Route inside 192.168.20.0 255.255.255.0 192.168.10.7 1

  Route inside 10.50.0.0 255.255.0.0 192.168.10.7 1

  #assume the following configuration sections appear elsewhere: static tunnel VPN, ACL, ifconfig, etc..

  # ----------------------------------------------------------------------

  Yes, this will work, even if you don't need political NAT for the 10.50.0.0 network. For PAT the 10.50.0.0 network when to anywhere (except via VPN) just do:

  Global 1 192.168.15.1 (outside)

  NAT (inside) 1 10.50.0.0 255.255.0.0

  As I said, you have works perfectly, the above is just an easier way to do it.

• Site-to-site and VPN Client on the same interface

  Hello

  Maybe it's a simple qeustion, and I also know it can be done on a SAA.

  But is it possible to have ipsec-l2l tunnels and external client ipsec VPN on the same interface on a router? If so someone can give me a link on how to do it because I can't find 1.

  Thank you

  Here you go:

  http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a00809c7171.shtml

  Hope that helps.

• How to intercept the sockettimeout exception message and display in the user interface of the view?

  Hi my jdev - 11.1.1.7 version

  I ask a socket connection in my AM and I want to catch the exception of the sockettimeout of t and display the error message in the user interface of the view layer.

  I use customException class that extends DCErrorHandlerImpl, but if we use try catch, then exceptions doesnot reach customclass.

  How to catch exceptions and return to view the layer if we use the operation binding. ?

  Because you call the operation via the link layer, which is perfectly fine, you do not get an exception at all. Exceptions thrown in methods called via the link layer are captured by the framework and transferred to the appellant in the operation binding.

  For that, you get the list of errors after the call returns and add them as messages of faces

  execute the method

  Method.Execute ();

  List errors = method.getErrors ();

  If (! errors.isEmpty ()) {}

  handle errors errors here is a list of exceptions!

  We only get the first

  E receive = errors.get (0);

  FacesMessage msg = new FacesMessage (FacesMessage.SEVERITY_ERROR, e.getMessage (), "");

  FacesContext.getCurrentInstance () .addMessage (null, msg);

  }

  no error return to normal work

  Timo

• Error message is "launch the user interface and to reinstall the application" after executing the quick backup.

  Original title: speedy

  My pc tells me to open the settings of the user interface on my windows laptop 8. I currently have

  has ran a quick backup, and now iiiimy pc asks me to open the user interface and I have to reinstall the application

  not known were and how to find what to do.

  Hello

  Please contact Microsoft Community. I've surely you will help solve this problem.

  To better understand the issue, let me know if you get this error when executing quick backup?

  If you get this error message when running fast backup software, you can visit the article to uninstall and reinstall the software.

  http://TechSupport.SpeedyPC.com/system/templates/selfservice/speedybackup/#Portal/1013/article/8478/how-do-I-uninstall-and-reinstall-the-program

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• doubt Doc ID 1618305.1 how to install and configure the user interface for content with WebCenter content 11.1.1.8.0

  doubt Doc-ID 1618305.1 How to install and configure the user interface with WebCenter content 11.1.1.8.0 content

  The portal_domain field contains;

  AdminServer (admin) and Enterprise Manager, (port 7001)

  IBR_server1, (port 16250)

  UCM_server1, (port 16200)

  WC_Spaces1, (port 8888).

  On the same machine, I have another weblogic, admin and for the ITS.

  The case is that continued to develop for the upgrade to the new skin WebCenter content.

  That's my goal.

  Then I did some research and came to the following notes in support.

  1 - how to install and configure the UI content with WebCenter content 11.1.1.8.0 and 11.1.1.9.0 (Doc ID 1618305.1()

  https://support.Oracle.com/epmos/faces/DocContentDisplay?_afrLoop=290841671406625 & ID = 1618305.1 & _afrWindowMode = 0 & _adf. CTRL-State = c7eq7vwdt_216

  and

  2 - update of the 11.1.1.8.0 UI content after you apply the Patch of Bundle WebCenter content 3 (MLR 3) or higher (Doc ID 1617477.1()

  https://support.Oracle.com/epmos/faces/DocContentDisplay?_afrLoop=291485823387355 & ID = 1617477.1 & _afrWindowMode = 0 & _adf. CTRL-State = c7eq7vwdt_245

  The UCM_server1 has the following House / app / oracle / Middleware / Oracle_ECM1 /.

  And the list of patches;

  ===================================================================================================

  Installed products of higher level (1):

  Oracle WebCenter content management install 11.1.1.8.0

  There are 1 products in this House of Oracle.

  Installed products (40):

  Cloning of the 11g Application Server 11.1.1.8.0 component

  Enterprise Manager Application Server Integrator Plugin - Management Service Support11.1.1.7.0

  FMW Control Plugin for Oracle inbound refinery 11.1.1.8.0

  FMW Control Plugin for Oracle WebCenter Capture 11.1.1.8.0

  Component install SDK 11.1.0.9.0

  Oracle Application Server Configuration 11.1.1.7.0

  Part of Oracle 11.1.1.7.0 Bali

  Oracle 11.1.1.8.0 capture

  Common files Oracle WebCenter content management 11.1.1.8.0

  Oracle Content Server 11.1.1.8.0

  Content of Oracle 11.1.1.8.0 Server component

  Content access Content Server Oracle 11.1.1.8.0

  Access to the contents of the Oracle Content Server 11.1.1.8.0 files

  Oracle Content Server Core 11.1.1.8.0

  Oracle 11.1.1.8.0 server content distribution

  Oracle extended Windowing Toolkit 11.1.1.7.0

  Oracle Fusion Middleware Admin Config 11.1.1.6.0

  Oracle Help for Java 11.1.1.7.0

  Oracle Help for the Web - UIX 11.1.1.7.0

  Oracle Help for the Web Shared Library 11.1.1.7.0

  Oracle Help share library 11.1.1.7.0

  Ice browser Oracle 11.1.1.7.0

  Oracle IRM                                                           11.1.1.6.0

  Oracle extended JFC Windowing Toolkit 11.1.1.7.0

  One-time correction of Oracle 11.1.0.9.9 installer

  Oracle outside in technology 8.4.0.0.0

  Oracle Remote Client of Intradoc 11.1.1.8.0

  Component of Oracle 11.1.1.7.0 rules

  Oracle SOA 11.1.1.7.0 workflow

  Universal Oracle install 11.1.0.9.0

  Oracle Upgrade Wizard 11.1.1.8.0

  Oracle Upgrade Wizard 11.1.1.8.0

  Upgrade Oracle WebCenter content management 11.1.1.8.0 Assistant

  Oracle WebCenter Capture 11.1.1.8.0

  Oracle Webcenter content - rights 11.1.1.7.0 documentalist

  Oracle WebCenter content - Universal Content Manager 11.1.1.8.0

  Oracle WebCenter content management install 11.1.1.8.0

  Oracle WebCenter content 11.1.1.8.0 management product suite

  Oracle WebCenter content: Imaging 11.1.1.8.0

  OracleAS Documentation 11.1.1.8.0

  There are 40 products installed in this House of Oracle.

  Interim plates (2):

  Patch 18188143: applied the sea Mar 19 17:37:32 BRT 2014

  Patch ID: 17263162

  Created February 5, 2014, 12:56:41 pm

  Bugs fixed:

  15872313, 17184457, 17515691, 16633496, 14317920, 15991141, 16892410

  14071471, 17929776, 13414481, 16042293, 17018964, 17627211, 16768600

  16037162, 14521663, 17768056, 14738077, 16460053, 17567819, 17806416

  15905591, 16080297, 17569908, 17043756, 18139768, 17211093, 17805499

  16418434, 16828356, 16671687, 17039391, 16698130, 17943394, 17632731

  17560900, 14246603, 15941347, 16045712

  Location of patch in the inventory:

  / app/Oracle/middleware/Oracle_ECM1/Inventory/oneoffs/18188143

  Patch location in the storage area:

  /app/Oracle/middleware/Oracle_ECM1/.patch_storage/18188143_Feb_5_2014_12_56_41

  Patch 18088049: applied the sea Mar 19 17:35:58 BRT 2014

  Patch ID: 17182855

  Created February 16, 2014 20:35:48 hrs PST8PDT

  Bugs fixed:

  17919101, 17894065, 17884570, 17883868, 17883112, 17854549, 17835742

  17832305, 17819213, 17812338, 17789722, 17783376, 17778867, 17761746

  17740542, 17733871, 17698852, 17658821, 17642431, 17636186, 17622384

  17616664, 17616611, 17616489, 17613656, 17608703, 17589960, 17581458

  17574153, 17567413, 17565564, 17558210, 17558068, 17546505, 17545841

  17540480, 17528590, 17514070, 17511368, 17511271, 17511089, 17501678

  17500375, 17475733, 17449617, 17421368, 17417817, 17416821, 17416807

  17416771, 17416377, 17416343, 17402732, 17401071, 17401052, 17397875

  17393920, 17393892, 17369286, 17368525, 17368096, 17362858, 17362130

  17354877, 17353764, 17352746, 17335303, 17335290, 17330493, 17324707

  17323595, 17323038, 17317268, 17314494, 17313064, 17313052, 17313000

  17312990, 17312933, 17312863, 17312366, 17298386, 17295962, 17290804

  17285105, 17270986, 17261952, 17255019, 17219134, 17216119, 17206903

  17201035, 17200854, 17199763, 17187804, 17185539, 17171852, 17171818

  17164502, 17160600, 17153780, 17074852, 17050451, 17049175, 17026301

  17008220, 17007746, 17007534, 17006378, 16999307, 16999291, 16991380

  16980256, 16980207, 16980196, 16979042, 16961904, 16958142, 16954858

  16941623, 16936055, 16936048, 16936036, 16936020, 16936006, 16935987

  16935976, 16921682, 16908287, 16858148, 16815976, 16796213, 13931337

  17424037, 17006115, 17171834

  OPatch succeeded.

  ==============================================================================================

  And contains the following configurations in config.cfg

  ==============================================================================================

  SocketAddressHostSecurityFilter = 127.0.0.1 | 0:0:0:0:0:0:0:1 | 192.168.1. * | 10.62.1.79

  xPortalSecurityPropagate = true

  Web server = javaAppServer

  AllowUpdateForGenwww = 1

  SearchIndexerEngineName = OracleTextSearch

  IndexerDatabaseProviderName = SystemDatabase

  AdditionalEscapeChars = -: #.

  FileEncoding = UTF8

  MaxQueryRows = 2000

  DisableAuthorizationTokenCheck = true

  IntradocServerPort = 4444

  SchemaPublishInterval = 604800

  SSAllowDelayedProjectWrites = true

  IdcServerThreadQueryTimeout = 120

  DisableQueryTimeoutSupport = false

  MaxSearchConnections = 20

  #Cache

  UseSearchCache = false

  #

  #AdditionalEscapeChars = _: #, -: {-}, has: A, GOLD: GOLD, CAN: CAN, AND: AND at the END:

  # Accesing a content item on a mapped Web URL (WebUrlMap) fails with the error: "unable to retrieve the content. Security access denied» (Doc ID 1639028.1()

  MaxAccountsInSecurityClause = 300

  # end (Doc ID 1639028.1()

  #Search fails for external users in WCC after upgrade to 11.1.1.8.0 (Doc ID 1676468.1()

  DoCaseInsensitiveAcctSearch = false

  # end (Doc ID 1676468.1()

  #MigrationFormatForfApplicationGUID = dCollectionName:dCollectionGUID

  ==============================================================================================

  To my UCM_Server1 content WebCenter.

  As I already have a WebCenter content I have to follow the second part of the note

  How to install and configure the UI content with WebCenter content 11.1.1.8.0 and 11.1.1.9.0 (Doc ID 1618305.1).

  Install and configure content WebCenter ADF WebUI against WebCenter Content Server

  Step 1) install the MDS schema

  (Step 2), install the Weblogic Server

  11 GR 1 material step 3) DOWNLOAD and install Oracle Application Development Framework (11.1.1.6.0) in the new WebUI WLS Middleware House, found here

  Step 4) Download and apply Patch 16, 546 129.

  Step 5) Download and apply Patch 16, 546 157.

  Step 6) download and apply the Patch and then 19,469,801, 18,102,108 Patch

  Step 7) copy the wccadf files in the field of user interface

  Step 8) Oracle on demand services (MDS) metadata registry

  Step 9) Place the WebCenter content domain user interface model

  Step 10) run the Setup Wizard on the new home of Middleware WebUI to create the new domain

  Step 11) updated the Oracle ADF of shared libraries

  Step 12) start the domain WebUI administration server

  Step 13) Save target Managed Server with the MDS repository and create the metadata partition

  Step 14) start the server managed WebUI.

  Step 15) associate UI WebCenter content to Content Server.

  Step 16) reboot the WebUI ADF server managed.

  Step 17 access the WebUI

  Step 18) complete the Configuration of the workflow

  Step 19) apply the latest Patch Bundle content UI of WebCenter

  MY DOUBT IS:

  To read the steps that I understood, to 19, with success, in the end, I will have an another WebLogic with a domain name and its respective EM.

  I have two servers weblogic?

  portal_domain (explained above) and a new wccui_domain wls and domain.

  This fix it?

  Two WLS to keep WebCenter portal and content, and other elements.

  Because I'm not able to do with the WLS even where I UCM_server1 today?

  Thanks for all suggestions and criticism.

  To read the steps that I understood, to 19, with success, in the end, I will have an another WebLogic with a domain name and its respective EM.

  I have two servers weblogic?

  portal_domain (explained above) and a new wccui_domain wls and domain.

  This fix it?

  Two WLS to keep WebCenter portal and content, and other elements.

  Because I could not do with the WLS even where I UCM_server1 today?

  Yes, up to 11.1.1.9.0, you will need to install a new wls House (new wls server admin) and then configure WCC ui there. User interface and COE will not work in the same field. You can have the portal and content under the same House of wls and install a new one for the user interface.

  This is due to a problem with ADF and WCC libraries.

  With 12 c, this dependence is not there, and you can install / configure all 3 (Portal, content and adf ui) applications on the same domain.

• Is it possible to resize the text and icons in the user interface?

  I'm on a Windows 10, 15.6 screen laptop "4 k. The menu bar along the top is sized very well, most of the time. However, all the icons and the text to actually work on fuse are too small for me to look at and click on without having a fight.

  Are there ways to manipulate the proportions of the UI? Thank you!

  Hi Brandon!  Great question!  Unfortunately for the insight we have not a scalable user interface, but it's certainly something that we will keep in mind for future releases.  Now this is resolution dependent so you need reduce the resolution setting (we've only really tested until about 2 k ~ monitors).  The user interface is pretty basic at the moment, but there are a few changes, you can do it.  Here is a link to the user guide on the user interface customizations for details - but you can change the position of the toolbars by clicking the separation Strip and you can change the width of the canvas/editor fracture by dragging on the edge of the editor Panel.